1、Designation: C324 01 (Reapproved 2014)Standard Test Method forFree Moisture in Ceramic Whiteware Clays1This standard is issued under the fixed designation C324; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revis
2、ion. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of freemoisture in ceramic whiteware clays. Whiteware clays may beshipped as a bulk sh
3、ipment in lumps, a bulk shipment ofshredded or coarsely ground clay, or in bagged lots of groundor airfloated clay. Directions are given in this test method forobtaining representative samples of the clay shipment to beused in subsequent tests for the properties of the clay in theshipment.1.2 This s
4、tandard does not purport to address all of thesafetyconcerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1
5、 ASTM Standards:2C332 Specification for Lightweight Aggregates for Insulat-ing Concrete3. Sampling3.1 The sample shall be obtained in accordance with Speci-fication C332. The sample submitted for testing shall weigh notless than 1000 g and shall be kept in an airtight container toprevent loss of wat
6、er before testing.4. Procedure4.1 Remove the sample of clay from its container. Weighabout 500 g of the sample to the nearest 0.1 g. Spread out theweighed portion of the sample in a weighed shallow metal orporcelain container, and dry at 100 to 110C for 24 h in adrying oven. Reweigh the dried clay,
7、as quickly as possible, tothe nearest 0.1 g.5. Calculation5.1 Calculate the percentage of free moisture to the nearest0.1 % as follows:Free moisture, dry weight basis, % 5 A 2 B!/B# 3 100 (1)Free moisture, wet weight basis, % 5 A 2 B!/A# 3 100 (2)where:A = “as-received” weight of the portion of the
8、sample usedandB = weight of sample after drying.6. Keywords6.1 ceramic whiteware clays; free moistureASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that det
9、ermination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved o
10、r withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel th
11、at your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints
12、 (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM w
13、ebsite (www.astm.org/COPYRIGHT/).1This test method is under the jurisdiction ofASTM Committee C21 on CeramicWhitewares and Related Products and is the direct responsibility of SubcommitteeC21.04 on Raw Materials.Current edition approved Jan. 1, 2014. Published February 2014. Originallyapproved in 19
14、53. Last previous edition approved in 2001 as C324 01(2007). DOI:10.1520/C0324-01R14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1
