ASTM C475 C475M-2017 Standard Specification for Joint Compound and Joint Tape for Finishing Gypsum Board 《精修石膏板用添缝混合料和填缝带料的标准规格》.pdf
《ASTM C475 C475M-2017 Standard Specification for Joint Compound and Joint Tape for Finishing Gypsum Board 《精修石膏板用添缝混合料和填缝带料的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM C475 C475M-2017 Standard Specification for Joint Compound and Joint Tape for Finishing Gypsum Board 《精修石膏板用添缝混合料和填缝带料的标准规格》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: C475/C475M 17Standard Specification forJoint Compound and Joint Tape for Finishing GypsumBoard1This standard is issued under the fixed designation C475/C475M; the number immediately following the designation indicates the yearof original adoption or, in the case of revision, the year of
2、 last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope*1.1 This specification covers all-
3、purpose, taping and finish-ing joint compounds, paper joint tape, and glass-mesh jointtape.1.1.1 The joint materials used in this standard are designedto be used with gypsum board installed in accordance withSpecification C840.1.2 This specification also covers the minimum require-ments for an assem
4、bly of taping and all-purpose compound andjoint tape.1.3 The text of this specification references notes andfootnotes that provide explanatory material. These notes andfootnotes (excluding those in tables and figures) shall not beconsidered as requirements of the specification.1.4 The values stated
5、in either inch-pound or SI (metric)units are to be regarded separately as standard. Within the text,the SI units are shown in parentheses. The values stated in eachsystem shall be used independent of the other. Values from thetwo systems shall not be combined.1.5 This international standard was deve
6、loped in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Doc
7、uments2.1 ASTM Standards:2C11 Terminology Relating to Gypsum and Related BuildingMaterials and SystemsC474 Test Methods for Joint Treatment Materials for Gyp-sum Board ConstructionC840 Specification forApplication and Finishing of GypsumBoardD123 Terminology Relating to TextilesD3882 Test Method for
8、 Bow and Skew in Woven andKnitted FabricsF1615 Specification for Cautionary Labeling for Five-Gallon Open-Head Plastic Containers3. Terminology3.1 DefinitionsDefinitions shall be in accordance withTerminology C11.3.2 Definitions of Terms Specific to This Standard:3.2.1 glass-mesh joint-tape, na stri
9、p of multidirectionalglass yarn material designed to reinforce the joint between twogypsum boards.3.2.2 joint tape, na strip of material used to conceal andreinforce the joint between two gypsum boards.3.2.3 joint tape, self-adhering, na joint tape manufacturedto adhere directly to the substrate.3.2
10、.3.1 DiscussionTapes having this quality do not requiremechanical or embedment means of attachment to the sub-strate.3.2.4 paper joint tape, na strip of paper reinforcingmaterial designed to be embedded in the joint compound and toreinforce the joint between two gypsum boards.3.2.5 skewness, nas def
11、ined in Terminology D123.4. Physical Properties4.1 GeneralThe physical properties shall be determined inaccordance with Test Methods C474, except as noted.4.2 Joint Compounds.4.2.1 Check CrackingNo cracks in the thinner half of thewedge and no deep fissure cracks in the thicker half of thewedge.4.2.
12、2 PutrefactionNo putrefaction in less than four days.4.2.3 ShrinkageNot more than 35 % by volume.4.3 Joint Tape:1This specification is under the jurisdiction of ASTM Committee C11 onGypsum and Related Building Materials and Systems and is the direct responsibilityof Subcommittee C11.02 on Specificat
13、ions and Test Methods for Accessories andRelated Products.Current edition approved Oct. 1, 2017. Published November 2017. Originallyapproved in 1961. Last previous edition approved in 2015 as C475/C475M 15.DOI: 10.1520/C0475_C0475M-17.2For referenced ASTM standards, visit the ASTM website, www.astm.
14、org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C
15、700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the
16、World Trade Organization Technical Barriers to Trade (TBT) Committee.14.3.1 The following tests are required of all joint tape:4.3.1.1 WidthShall be not less than 178 in. (48 mm) normore than 214 in. (60 mm). The width of an individual rollshall vary not more than 6132 in. (1 mm).4.3.1.2 ThicknessSh
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMC475C475M2017STANDARDSPECIFICATIONFORJOINTCOMPOUNDANDJOINTTAPEFORFINISHINGGYPSUMBOARD 石膏板 用添缝 混合

链接地址:http://www.mydoc123.com/p-466691.html