ASTM C834-2014 Standard Specification for Latex Sealants《乳胶密封剂的标准规格》.pdf

上传人:medalangle361 文档编号:508478 上传时间:2018-12-01 格式:PDF 页数:3 大小:71.37KB
下载 相关 举报
ASTM C834-2014 Standard Specification for Latex Sealants《乳胶密封剂的标准规格》.pdf_第1页
第1页 / 共3页
ASTM C834-2014 Standard Specification for Latex Sealants《乳胶密封剂的标准规格》.pdf_第2页
第2页 / 共3页
ASTM C834-2014 Standard Specification for Latex Sealants《乳胶密封剂的标准规格》.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation: C834 14Standard Specification forLatex Sealants1This standard is issued under the fixed designation C834; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the

2、 year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This specification covers one component latex sealantsused for sealing joints in bui

3、lding construction.1.2 A sealant meeting the requirements of this specificationshall be classified by the manufacturer to be one of the typesand grades defined in Section 4.1.3 The values stated in SI units are to be regarded as thestandard. The inch-pound in parenthesis are provided forinformation

4、purposes only.1.4 The following precautionary caveat pertains only to thetest method portion, Section 10, of this Specification:Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appro

5、priate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.NOTE 1Currently, there is no ISO standard similar to this specifica-tion.2. Referenced Documents2.1 ASTM Standards:2C717 Terminology of Building Seals and SealantsC732 Test Method for Aging Effe

6、cts of Artificial Weatheringon Latex SealantsC734 Test Method for Low-Temperature Flexibility of LatexSealants After Artificial WeatheringC736 Test Method for Extension-Recovery and Adhesion ofLatex SealantsC1183 Test Method for Extrusion Rate of Elastomeric Seal-antsC1193 Guide for Use of Joint Sea

7、lantsC1241 Test Method for Volume Shrinkage of Latex SealantsDuring CureD2202 Test Method for Slump of SealantsD2203 Test Method for Staining from SealantsD2377 Test Method for Tack-Free Time of Caulking Com-pounds and Sealants3. Terminology3.1 DefinitionsDefinitions of the following terms apply tot

8、his specification and are found in Terminology C717: adhesivefailure (adhesion loss), cure, joint, latex sealant, sealant,shrinkage (volume), standard conditions, and substrate.4. Classification of Sealants4.1 A sealant qualifying under this specification shall beclassified by type and grade as foll

9、ows:4.1.1 Type OPAn opaque sealant containing color pig-ments or extender pigments, or both, that has no more than30 % volume shrinkage (see 10.1.3).4.1.2 Type CA clear or translucent sealant that has nomore than 50 % volume shrinkage (see 10.1.3).4.1.3 Grade 18CA sealant that meets the requirements

10、for low temperature flexibility (see 7.1) when tested at 18C(0F).4.1.4 Grade 0CA sealant that meets the requirements forlow temperature flexibility (see 7.1) when tested at 0C (32F).4.1.5 Grade NFA sealant that does not meet the require-ments for low temperature flexibility of Grade 0C (see 4.1.4).5

11、 Materials and Manufacture5.1 The sealant shall be composed of latex formulated withappropriate fillers, pigments, and chemical additives to result inconformance to this specification.5.2 All material and workmanship shall be in accordancewith good commercial practice. The producer is permitted awi

12、de latitude in choice of raw materials for making theseproducts. Consequently, there is no implication that the com-pounds are equivalent in all physical properties.5.3 The manufacturing process shall be such as will ensurea homogeneous mix, free of defects that would affectserviceability, and provi

13、de a consistency suitable for immedi-ate application.1This specification is under the jurisdiction of ASTM Committee C24 onBuilding Seals and Sealants and is the direct responsibility of Subcommittee C24.10on Specifications, Guides and Practices.Current edition approved June 1, 2014. Published July

14、2014. Originally approvedin 1976. Last previous edition approved in 2010 as C834 10. DOI: 10.1520/C0834-14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the stand

15、ards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States16. General Requirements6.1 The sealant in the original unopened container shallmeet the requirements of this specification for at least 12mo

16、nths from the date of manufacture when stored at atemperature neither below 5C (41F) nor exceeding 26.7C(80F).6.2 After 21 days cure at standard conditions, the color ofthe sealant shall be that color that has been agreed uponbetween the purchaser and the supplier.6.3 The sealant is intended for app

17、lication to clean substratesurfaces only.7. Physical Properties7.1 The sealant shall conform to the physical requirementsspecified in Table 1 according to type and grade.8. Significance and Use8.1 This specification covers two types and three grades oflatex sealants as described in Section 4 that ar

18、e formulated forgeneral caulking and sealing operations in building construc-tion. It should be recognized by the user that not all sealantsmeeting this specification are suitable for all applications andall substrates. It is essential, therefore, that the type and gradebe specified for proper descr

19、iption of a sealant. Test methodsrelate to special standard substrates of glass, wood and alumi-num. If tests are required using substrates in addition to orother than standard, they should be so specified for testing.8.2 Refer to Guide C1193 for information on the proper useof sealants meeting this

20、 specification.9. Sampling9.1 The sealant to be tested for conformance to this speci-fication shall be taken directly from a randomly selectedcontainer as commercially supplied by the manufacturer.10. Test Methods10.1 Perform all of the following tests at standard condi-tions. Condition sealant samp

21、les for at least5hatstandardconditions before any tests are conducted.10.1.1 Extrudability After AgingTest Method C1183, Pro-cedure B.10.1.2 Artificial WeatheringTest Method C732 (500 hexposure).10.1.3 Volume ShrinkageTest Method C1241.10.1.4 Low-Temperature FlexibilityTest Method C734(500 h Artific

22、ial Weathering exposure). For 0C sealants, thetest method is modified to perform the bend at 0 6 1C (32 62F).NOTE 2The exposure times for the accelerated weathering tests usedin this specification are meant to ensure a minimum level of performanceand cannot be used to estimate service life in any pa

23、rticular location.10.1.5 Extension-Recovery and AdhesionTest MethodC736.10.1.6 SlumpTest Method D2202 modified to advance theplunger to its maximum extent, leaving a solid cylinder ofsealing compound 38 mm (112 in.) in diameter and 10 mm (38in.) thick, ready to flow down the face of the instrument.1

24、0.1.7 StainingTest Method D2203.10.1.8 Tack-Free TimeTest Method D2377 modified toexpose the specimen for 1 h before applying polyethylene stripfor Type OP and modified to expose the specimen for 24 hbefore applying the polyethylene strip for Type C sealants.11. Packaging11.1 Unless otherwise specif

25、ied in the contract or order, thematerial shall be packaged in standard commercial containersso constructed as to ensure acceptance by common or othercarrier for safe transportation at the lowest rate to the point ofdelivery.11.2 Shipping containers shall be marked with the name,grade, and quantity

26、of the material contained therein, as definedby the contract or order under which shipments are made. Thename of the manufacturer, the lot and batch number of thecontract order, and the date of manufacture shall also beshown.12. Keywords12.1 latex sealantTABLE 1 Physical RequirementsTest Requirement

27、sASTMTest MethodExtrudability 2 g/s, minimum C1183, Proce-dure BArtificial weathering: 500 h C732Wash-out none, after weatheringSlump none, after weatheringCracking none, after weatheringDiscoloration as acceptable to purchaserAdhesion loss 25 % max (estimated on the basisof a total possible bond ar

28、eaof 45.16 cm2(7 in.2)Volume shrinkage:Type OP 30 % max C1241Type C 50 % maxLow-temperature flex-ibility:After 500 h Artificial Weathering expo-sureGrades 18 and 0 no cracking through to substrate oradhesion lossC734AGrade NF noneRecovery 75 % min (average of all specimens) C736Adhesion loss 25 % or

29、 19.35 cm2(3 in.2) max (oftotal bond area of all specimens)C736Slump 4 mm (0.15 in.) max(on each specimen)D2202BStain index 3 max D2203Tack-free time no material adhering to plastic strip D2377CColor as acceptable to purchaser 6.2ASee 10.1.4 for modification of this test method for 0C.BSee 10.1.6 fo

30、r modification to this test method.CSee 10.1.8 for modification to this test method.C834 142ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determinatio

31、n of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdra

32、wn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your c

33、omments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single

34、or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 143

展开阅读全文
相关资源
猜你喜欢
  • BS ISO 7764-2006 en_6592  Iron ores - Preparation of predried test samples for chemical analysis《铁矿石.化学分析用预干燥试样的制备》.pdf BS ISO 7764-2006 en_6592 Iron ores - Preparation of predried test samples for chemical analysis《铁矿石.化学分析用预干燥试样的制备》.pdf
  • BS ISO 7770-2009 en_5958  Textiles - Test method for assessing the smoothness appearance of seams in fabrics after cleansing《纺织品.去污后织物接缝表面平滑度评定的试验办法》.pdf BS ISO 7770-2009 en_5958 Textiles - Test method for assessing the smoothness appearance of seams in fabrics after cleansing《纺织品.去污后织物接缝表面平滑度评定的试验办法》.pdf
  • BS ISO 7780-1998 en_1548  Rubber and rubber latices - Determination of manganese content - Sodium periodate photometric methods《橡胶和橡胶乳液.锰含量测定.高碘酸钠光度测定法》.pdf BS ISO 7780-1998 en_1548 Rubber and rubber latices - Determination of manganese content - Sodium periodate photometric methods《橡胶和橡胶乳液.锰含量测定.高碘酸钠光度测定法》.pdf
  • BS ISO 7789-2008 en_2844  Hydraulic fluid power Two- three- and four-port screw-in cartridge valves Cavities《液压传动.二通、三通和四通螺纹式插装阀.插装孔》.pdf BS ISO 7789-2008 en_2844 Hydraulic fluid power Two- three- and four-port screw-in cartridge valves Cavities《液压传动.二通、三通和四通螺纹式插装阀.插装孔》.pdf
  • BS ISO 78-2-1999 en_8154  Chemistry - Layout for standards - Methods of chemical analysis《化学.标准的格式.化学分析方法》.pdf BS ISO 78-2-1999 en_8154 Chemistry - Layout for standards - Methods of chemical analysis《化学.标准的格式.化学分析方法》.pdf
  • BS ISO 7800-2012 en_1260  Metallic materials Wire Simple torsion test《金属材料.线材.单向扭转试验》.pdf BS ISO 7800-2012 en_1260 Metallic materials Wire Simple torsion test《金属材料.线材.单向扭转试验》.pdf
  • BS ISO 7802-2013 en_5373  Metallic materials Wire Wrapping test《金属材料.线材.缠绕试验》.pdf BS ISO 7802-2013 en_5373 Metallic materials Wire Wrapping test《金属材料.线材.缠绕试验》.pdf
  • BS ISO 7832-2014 en_6271  Cinematography Photoelectric output factor of photographic-type audio-level test films Measurement and calibration《电影技术 光学型音频级试验胶片的光电输出率 测野和校准》.pdf BS ISO 7832-2014 en_6271 Cinematography Photoelectric output factor of photographic-type audio-level test films Measurement and calibration《电影技术 光学型音频级试验胶片的光电输出率 测野和校准》.pdf
  • BS ISO 7839-2006 en_3350  Textile machinery and accessories - Knitting machines - Vocabulary andclas sification《纺织机械和附件.针织机械.词汇和分类》.pdf BS ISO 7839-2006 en_3350 Textile machinery and accessories - Knitting machines - Vocabulary andclas sification《纺织机械和附件.针织机械.词汇和分类》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > ASTM

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1