ASTM D1309-1993(2010) Standard Test Method for Settling Properties of Traffic Paints During Storage《贮藏期间交通标志用色漆的沉淀特性的标准试验方法》.pdf

上传人:medalangle361 文档编号:509616 上传时间:2018-12-01 格式:PDF 页数:2 大小:54.75KB
下载 相关 举报
ASTM D1309-1993(2010) Standard Test Method for Settling Properties of Traffic Paints During Storage《贮藏期间交通标志用色漆的沉淀特性的标准试验方法》.pdf_第1页
第1页 / 共2页
ASTM D1309-1993(2010) Standard Test Method for Settling Properties of Traffic Paints During Storage《贮藏期间交通标志用色漆的沉淀特性的标准试验方法》.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation: D1309 93 (Reapproved 2010)Standard Test Method forSettling Properties of Traffic Paints During Storage1This standard is issued under the fixed designation D1309; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year

2、 of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers a laboratory procedure forsimulating in 2 weeks the settling that might occur in trafficpa

3、int during approximately 12 months normal storage.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibi

4、lity of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use. For a specifichazard statement, see Note in 5.2.2. Referenced Documents2.1 ASTM Standards:2D869 Test Method for Evaluating Degree of Settli

5、ng ofPaint3. Significance and Use3.1 Paints, if not formulated or processed properly, or both,may settle excessively. This test method is an attempt tosimulate the conditions that would accelerate settling of thepigment in order to evaluate settling properties within 2 weeks.The variables of this te

6、st method in conjunction with the verysubjective method of evaluating the degree of settling (TestMethod D869) raise questions as to the usefulness of the resultsfor specification compliance.4. Apparatus4.1 ContainerStandard 500-mL (1-pt), friction top canpaint container 85.5 6 1.5 mm (338 6116 in.)

7、 in diameter and98.5 6 1.5 mm (378 6116 in.) in height.4.2 Spatula, weighing 45 6 1 g with square-end blade 125mm (434 in.) in length and approximately 20 mm (1316 in.) inwidth. A suitable spatula may be prepared by cutting the tipfrom an ordinary 125-mm (5-in.) flexible steel laboratoryspatula to t

8、he specified length.4.3 Freezer, maintained at from 21 to 23.3C ( 5 to 10F).4.4 Oven, maintained at 71 6 1C (160 6 2F).4.5 Lid Clips.5. Procedure5.1 Thoroughly mix the paint to be evaluated to a homoge-neous consistency. Transfer enough of the paint to a 500-mL(1-pt) paint can to fill it to within 1

9、3 mm (12 in.) of the top.Close the can tightly, securing the lid with four clips, andsubject it to the following exposure cycle.5.1.1 Monday through Friday:5.1.1.1 Place in freezer at 8:00 a.m.5.1.1.2 Transfer to oven at 10:00 a.m.5.1.1.3 Transfer to freezer at 2:00 p.m.5.1.1.4 Transfer to oven at 4

10、:00 p.m.5.1.2 From 4:00 p.m. Friday until 8:00 a.m. Monday:5.1.2.1 Place in the oven at 4:00 p.m. Friday.5.1.2.2 At 8:00 a.m. Monday morning, after the can hasbeen in the oven over a weekend, place it in the freezer andcontinue the cycles described above for another 7 days. Eachtime the can of paint

11、 is removed from the oven give it onesharp “spank” on the table top. The spank consists of a shortrapid jar of the bottom of the can of paint against the top of thetable. The violence of the jar is such that if the bottom of thecan of paint were spanked against the platform of a scaleinstead of a ta

12、ble top the scale would register approximately2.27 kg (5 lb) weight.5.2 At the completion of the exposure, allow the paint tocool at room temperature for 4 h and determine the degree ofsettling in accordance with Test Method D869.NOTE 1Open cans slowly and carefully to allow release of residualvapor

13、 pressure.1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.44 on Traffic Coatings.Current edition approved Dec. 1, 2010. Published December 2010. Originallyapproved in 1954.

14、 Last previous edition approved in 2004 as D1309 93 (2004).DOI: 10.1520/D1309-93R10.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary p

15、age onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6. Report6.1 Report the “accelerated settling rating” in accordancewith the degree of settling scale given in the Procedure sectionof Test Method D869.7. Precisio

16、n and Bias7.1 Due to the poor precision of Test Method D869,ifitisused in a specification, the maximum deviation from thesettling limits specified should be agreed upon between thepurchaser and the seller.7.2 BiasBias cannot be determined.8. Keywords8.1 paint testing; settling test; traffic paintAST

17、M International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are en

18、tirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsa

19、nd should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee

20、on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D1309 93 (2010)2

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > ASTM

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1