1、Designation: D 2118 05 (Reapproved 2009)Standard Practice forAssigning a Standard Commercial Moisture Content forWool and its Products1This standard is issued under the fixed designation D 2118; the number immediately following the designation indicates the year oforiginal adoption or, in the case o
2、f revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice recommends that a single value be adoptedfor the commercial moisture content of
3、wool in any of thefollowing forms:1.1.1 Scoured,1.1.2 Carbonized and neutralized,1.1.3 Noils, uncarbonized,1.1.4 Top, oil or dry combed,1.1.5 Yarn, worsted,1.1.6 Yarn, woolen,1.1.7 Yarn, hand knitting, or1.1.8 Fabric.1.2 LimitationsGrease wool, pulled wool, and wool withpH below 5.0 are excluded fro
4、m this practice.1.3 This standard does not purport to address the safetyconcerns, if any, associated with its use. It is the responsibilityof the user of this standard to establish appropriate safety andhealth practices and determine the applicability of regulatorylimitations prior to use.2. Referen
5、ced Documents2.1 ASTM Standards:2D 123 Terminology Relating to TextilesD 584 Test Method for Wool Content of Raw WoolLaboratory ScaleD 1909 Standard Table of Commercial Moisture Regainsfor Textile FibersD 2720 Practice for Calculation of Commercial Weight andYield of Scoured Wool, Top, and Noil for
6、Various Com-mercial CompositionsD 4845 Terminology Relating to Wool3. Terminology3.1 For definitions of textile terms used in this practice:carbonized and neutralized wool, commercial moisture con-tent, wool, refer to Terminology D 4845.3.2 For the definition of wool and other textile terms used int
7、his practice, refer to Terminology D 123.4. Significance and Use4.1 The purpose of this practice is to bring about uniformityof commercial moisture standards in all ASTM specificationsrelating to wool and its products.4.2 This practice provides a recommended single value fora standardized commercial
8、 moisture content for wool and itsproducts. This avoids difficulties encountered in calculating theamount of moisture-free fiber present in a given mass of woolin any one of the forms listed in 1.1.1 to 1.1.8 due to tradepractices which recognize various commercial moisture allow-ance values used by
9、 certain segments of the trade. (See TestMethod D 584, Section 3.5, Table D 1909, Note E, and theTables in Practice D 2720).4.3 The recommended commercial moisture content shouldbe used where it is desirable to avoid problems in determiningmoisture-free fiber content when the form of the wool ischan
10、ged. For example: from scoured wool (12.0 % moisturecontent) to worsted yarn, dry spun (13.04 % moisture content).5. Recommended Commercial Moisture Content5.1 Use 12.0 % as the commercial moisture content forwool and its products.NOTE 1For other commercial regain values commonly used for woolin var
11、ious forms, refer to Table 1 in Table D 1909, Table 1 in PracticeD 2720, and Note 1 in Test Method D 584.5.2 The value of 12.0 % has been assigned as the commer-cial moisture content for the following reasons:5.2.1 A moisture content of 12.0 % is approximately equalto 13.6 % moisture regain which ha
12、s been listed as theAmerican Moisture Regain specification for scoured wool.31This practice is under the jurisdiction ofASTM Committee D13 on Textiles andis the direct responsibility of Subcommittee D13.13 on Wool and Felt.Current edition approved July 1, 2009. Published August 2009. Originallyappro
13、ved in 1961. Last previous edition approved in 2005 as D 2118 05.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM webs
14、ite.3American Wool Handbook, Second edition, Table 17, p. 157.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.2.2 A moisture content of 12.0 % is the basis for theassessment of duty on the importation of raw wool into theU.S.4ASTM
15、International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are enti
16、rely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand
17、 should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on
18、 Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).4Tariff Schedules of the United States of America, Schedule 3, Part 1, SubpartC, Headnote 1(c).D 2118 05 (2009)2
