ASTM D2203-2001(2018) Standard Test Method for Staining from Sealants《密封剂着色的标准试验方法》.pdf
《ASTM D2203-2001(2018) Standard Test Method for Staining from Sealants《密封剂着色的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM D2203-2001(2018) Standard Test Method for Staining from Sealants《密封剂着色的标准试验方法》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D2203 01 (Reapproved 2018)Standard Test Method forStaining from Sealants1This standard is issued under the fixed designation D2203; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in
2、 parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers a laboratory procedure fordetermining whether a sample of sealant will cause staining ofthe substrate when in the contac
3、t with masonry, concrete, orstone (marble, limestone, sandstone, granite, etc.).1.2 The values stated in SI (metric) units are to be regardedas the standard. The values given in parentheses are providedfor information only.1.3 This standard does not purport to address all of thesafety concerns, if a
4、ny, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.NOTE 1Currently there is no ISO standard similar to this test method.1.4 Thi
5、s international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade
6、(TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2C510 Test Method for Staining and Color Change of Single-or Multicomponent Joint SealantsC717 Terminology of Building Seals and Sealants3. Terminology3.1 DefinitionsRefer to Terminology C717 for definitionsof the following terms used in this
7、 test method: compound,sealant, substrate.4. Significance and Use4.1 Staining of a building is an aesthetically undesirableoccurrence. This test method evaluates the likelihood of asealant causing an early stain on a porous substrate, when thestain is caused by gross exudation from the sealant. This
8、 testmethod does not predict staining caused by other factors.4.2 See also Test Method C510.5. Apparatus and Materials5.1 Convection Oven, having a temperature controlled at104.5 6 3C (220 6 5F).5.2 Brass Ring, 19 mm (34 in.) inside diameter, 19 mm (34in.) high, walls at one end beveled to a minimum
9、 diameter.5.3 Filter Paper, ten sheets, high-grade, rapid, qualitative 9cm in diameter.35.4 Aluminum Foil, household-type, 25.4 mm (1 in.) square.5.5 Weight, 300-g.5.6 Spatula, small, thin, steel.5.7 Glass Plate, at least 100 by 100 mm (4 by 4 in.).5.8 Desiccator, with drying agent.6. Sampling6.1 Ta
10、ke the test specimen from a previously unopenedcontainer and thoroughly mix before using, if required forhomogeneity.7. Conditioning7.1 Condition the sample in a closed container for at least 5hat236 2C (73.4 6 3.6F).8. Procedure8.1 Dry the filter papers for 5 to8hinanoven maintainedat 104.5 6 3C (2
11、20 6 5.4F).At the end of the drying period,remove from the oven and store in a desiccator until cool.8.2 Remove ten filter papers from the desiccator, staplethem together, and place them on a glass plate. Set the brassring with beveled edge down on the center of the filter papers.1This test method i
12、s under the jurisdiction ofASTM Committee C24 on BuildingSeals and Sealants and is the direct responsibility of Subcommittee C24.20 onGeneral Test Methods.Current edition approved Jan. 1, 2018. Published January 2018. Originallyapproved in 1963. Last previous edition approved in 2011 as D2203 01(201
13、1).DOI: 10.1520/D2203-01R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3This test method is based on the
14、 use of Whatman No. 1 filter paper,manufactured by Whatman, Inc., 9 Bridewell Place, Clifton, NJ 07073.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recogni
15、zed principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.1Fill the ring flush with thoroughly mixed sealant, taking care toi
16、ncorporate as little air as possible with the compound. Place a25.4-mm (1-in.) square piece of aluminum foil on top of thering, and the 300-g weight on top of that.8.3 Allow the filled ring to stand for 72 h at 23 6 2C (73.46 3.6F). Then slide a spatula under the brass ring and removethe ring and co
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD220320012018STANDARDTESTMETHODFORSTAININGFROMSEALANTS 密封剂 着色 标准 试验 方法 PDF

链接地址:http://www.mydoc123.com/p-511194.html