1、Designation: D227/D227M 03 (Reapproved 2018)Standard Specification forCoal-Tar-Saturated Organic Felt Used in Roofing andWaterproofing1This standard is issued under the fixed designation D227/D227M; the number immediately following the designation indicates the yearof original adoption or, in the ca
2、se of revision, the year of last revision. A number in parentheses indicates the year of last reapproval.A superscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.This specificati
3、on replaces Federal specification HH-R-595, Type 15C.1. Scope1.1 This specification covers coal-tar-saturated organic feltintended to be used with coal-tar pitches conforming to theappropriate requirements of Specification D450/D450M in theconstruction of built-up roofs and in the construction ofwat
4、erproofing systems.1.2 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used independently of the other. Combiningvalues from the two systems may result in n
5、on-conformancewith the standard.1.3 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade O
6、rganization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D146/D146M Test Methods for Sampling and TestingBitumen-Saturated Felts and Woven Fabrics for Roofingand WaterproofingD450/D450M Specification for Coal-Tar Pitch Used inRoofing, Dampproofing, and Waterp
7、roofingD1079 Terminology Relating to Roofing and Waterproofing3. Terminology3.1 DefinitionsFor definitions of terms used in thisspecification, refer to Terminology D1079.4. Materials and Manufacture4.1 In the process of manufacture, a single thickness of dryfelt shall be saturated with refined coal-
8、tar from which some ofthe more volatile constituents have been removed.4.2 The felt shall be produced principally from organicfibers or mixtures thereof. The surface of the felt shall beuniform and relatively smooth. Upon splitting or tearing on thebias, the felt shall appear reasonably free of lump
9、s and particlesof foreign substances.5. Physical Requirements5.1 The material shall conform to the physical requirementsprescribed in Table 1.5.2 The finished product shall not crack nor be so sticky asto cause tearing or other damage upon being unrolled attemperatures between 10 and 60C 50 and 140F
10、.6. Workmanship, Finish, and Appearance6.1 The felt shall be saturated and shall show no unsaturatedspots at any point upon cutting 50-mm 2-in. wide strips atrandom across the entire sheet and splitting them open to theirfull length.6.2 The surface of the felt shall not be coated or coveredwith talc
11、 or other substances that would tend to interfere withadhesion between the felt and the plying cement.6.3 The finished material shall be free of visible externaldefects such as holes, ragged or untrue edges, breaks, cracks,tears, protuberances, and indentations.7. Sampling and Test Methods7.1 Sample
12、 the material and determine the properties enu-merated in this specification in accordance with Test MethodsD146/D146M.8. Inspection8.1 InspectionInspection shall be in accordance with therequirements of this specification.1This specification is under the jurisdiction of ASTM Committee D08 onRoofing
13、 and Waterproofing and is the direct responsibility of Subcommittee D08.04on Felts, Fabrics and Bituminous Sheet Materials.Current edition approved Sept. 1, 2018. Published October 2018. Originallyapproved in 1925. Last previous edition approved in 2011 as D227/D227M 03(2011)1. DOI: 10.1520/D0227_D0
14、227M-03R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Driv
15、e, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations iss
16、ued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.18.2 Inspection AlternativesAlternative inspection require-ments shall be determined by and as agreed upon between thepurchaser and the supplier.9. Rejection and Resubmittal9.1 Failure to ConformFailure to conform to any
17、 of therequirements as stated in this specification constitutes groundsfor rejection.9.2 Rejection RedressThe supplier shall have the right toinspect the rejected materials. The supplier and the purchasershall agree to the quantity of rolls deemed unacceptable. Thesupplier shall then have the right
18、to submit the same number ofnew rolls as replacement.10. Packaging and Package Marking10.1 Unless otherwise agreed upon between the supplierand purchaser, each package shall be plainly marked with thesuppliers name, the product brand, theASTM designation, andtype of bitumen if not evident in the lab
19、el name of the product.10.2 The rolls shall be securely wrapped or banded in amanner that completely encircles the roll and will preventslipping or unrolling.10.3 No roll shall contain more than two pieces, and nomore than 3 % of the rolls in any lot shall contain two pieces.If a roll contains a man
20、ufacturing splice, the splice shall beclearly marked.11. Keywords11.1 built-up roofs; coal tar saturated; membrane; organicfelt; waterproofingASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of thi
21、s standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five yea
22、rs andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical commit
23、tee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 1942
24、8-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the sta
25、ndard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 1 Physical Requirements for Coal-Tar-Saturated Organic FeltWidth of roll, mm in. 914 36 0.7 %AArea of Roll as agreed upon between the purchaser and the sellerNet mass of s
26、aturated felt, min, g/m2lb 100 ft2 635 13Moisture, at point of manufacture, max %B4.3Average breaking strength, min, kN/m lbf/in. of widthCLongitudinal (with the fiber grain) 5.3 30Transverse (across the fiber grain) 2.6 15Pliability, 13 mm 12 in. radius bend at 25C 77F no failuresMass of desaturate
27、d (unsaturated) felt, min, g/m2lb 100 ft2D254 5.2Mass of saturant (coal-tar), min, g/m2lb/100 ft2E356 7.3AOther widths may be agreed upon between the purchaser and the seller.BAt time of manufacture, products with higher moisture content at time of installation may cause hot materials to foam, creat
28、ing interply voids that may result in blisters.CIf specimens fail to conform to the requirements for breaking strength after conditioning for 2 h, a retest shall be made on specimens conditioned for 72 h. The materialshall be accepted or rejected on the basis of the retest.DThe moisture-free felt sh
29、all meet this requirement prior to saturation. Coal-tar-saturated felt cannot be thoroughly desaturated by any known means; only an approximatevalue may be obtained through desaturation.EThe mass of the saturant shall be not less than 1.4 times the mass of the desaturated (unsaturated) dry felt.D227/D227M 03 (2018)2