1、Designation: D269 97 (Reapproved 2015)Standard Test Method forInsoluble Matter in Rosin and Rosin Derivatives1This standard is issued under the fixed designation D269; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of las
2、t revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the amountof insoluble matter in rosin and rosin derivatives as describedin
3、Terminology D804.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesafety problems, if any, associated with its use. It is theresponsibility of the user of this standard
4、 to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D804 Terminology Relating to Pine Chemicals, IncludingTall Oil and Related ProductsE11 Specification for Woven Wire Test Sieve Clo
5、th and TestSieves3. Significance and Use3.1 Rosin, particularly gum and wood rosin, occasionallycontains small amounts of contamination such as sand, dirt orbark. Rosin derivatives occasionally contain traces of insolublematerial as a result of the raw materials used in their productionor they may b
6、e generated during the production process. In allinstances the presence of such insoluble material should beminimal. This test method describes a rapid and reliableprocedure for determining the amount of such insoluble matter.It is based on the knowledge that rosin and most of itsderivatives are sol
7、uble in numerous organic solvents whereasmost common contaminants are not. It is especially useful forinternal quality control rather than sales specifications.4. Apparatus4.1 Beaker, 800 mL.4.2 Magnetic Stirring Hot Plate with Polytetrafluoroethyl-ene (PTFE) Stirbar, or hot plate with manual stirri
8、ng rod.4.3 Precut Stainless Steel Circular Screen, 325 mesh with0.0014-in. wire diameter. (44-m openings) as described inSpecification E11.4.4 Two-Piece Filter Apparatus, appropriate to hold thestainless steel screens without leaking.4.5 Analytical Balance, capable of weighing 0.0001 g.4.6 Laborator
9、y Tweezers.4.7 Forced Draft Oven.5. Reagents5.1 Clean Toluene, Hexane, Mineral Spirits, or other suit-able solvent for the specific material to be checked in, asagreed upon between the customer and the supplier.6. Procedure6.1 Rinse the pre-cut screen thoroughly with the solvent toclean it before us
10、e.6.1.1 Dry the clean screen at 105 to 110C for 30 min, coolin a desiccator, and weigh.6.1.2 Record the weight of the dry screen to the nearest0.0001 g.6.1.3 Place the screen in the filter apparatus and secure it toprevent leakage.NOTE 1Always use tweezers when handling the pre-cut screen.6.2 Weigh
11、100 6 0.1 g of freshly powdered material to betested into an 800-mL beaker. Add 150 mL of solvent. Place aPTFE-coated magnetic stir bar into the beaker, and place thebeaker on a hot plate. Heat and stir the material until it iscompletely dissolved. Do not boil the solvent.6.3 Immediately pour the so
12、lution through the screen. Rinsethe beaker and filter apparatus three times with additional hotsolvent.6.4 Disassemble the filter apparatus, remove the screen, andplace it in a forced draft oven, contaminated side up. Dry thescreen to constant weight at 105 to 110C. (1 h is usually1This test method
13、is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.34 on Pine Chemicals and Hydrocarbon Resins.Current edition approved Dec. 1, 2015. Published December 2015. Originallyapproved in 1927. Last p
14、revious edition approved in 2011 as D269 97 (2011).DOI: 10.1520/D0269-97R15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onth
15、e ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1sufficient), cool in a desiccator, and weigh. Record the weightof the dry contaminated screen to the nearest 0.0001 g.7. Calculationweight contaminated screen (1)Percent i
16、nsolubles 52 weight clean screen.weight of sample31008. Report8.1 Report the percent insoluble matter to the nearest0.01 %.9. Precision and Bias9.1 It is not practical to measure the precision and bias ofthe procedure in this test method because this test method isprimarily used for internal quality
17、 control purposes rather thanfor customer specification purposes.10. Keywords10.1 insoluble; rosin; rosin derivativesASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly
18、advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, eit
19、her reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend
20、. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Ind
21、ividual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 97 (2015)2
