1、Designation: D91 02 (Reapproved 2017)Standard Test Method forPrecipitation Number of Lubricating Oils1,2This standard is issued under the fixed designation D91; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of last revis
2、ion. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the U.S. Department of Defense.1. Scope1.1 This test method covers the determination
3、of the pre-cipitation number of steam cylinder stocks and black oils, andcan be used for other lubricating oils.1.2 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.3 This standard does not purport to address all of thesafety c
4、oncerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.4 This international standard was developed in accor-dance with international
5、ly recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:3D4057 Practic
6、e for Manual Sampling of Petroleum andPetroleum ProductsD4177 Practice for Automatic Sampling of Petroleum andPetroleum Products3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 ASTM precipitation number, of lubricating oils, nthenumber of millilitres of precipitate formed when
7、10 mL oflubricating oil are mixed with 90 mL of ASTM precipitationnaphtha, and centrifuged under the conditions of the test.4. Significance and Use4.1 Fully refined petroleum oils normally contain no naph-tha insoluble material. Semirefined or black oils frequentlycontain some naphtha insoluble mate
8、rial (sometimes referredto as asphaltenes ). This test measures the amount of naphthainsoluble material in the oil. This quantity is reported as theprecipitation number.5. Apparatus5.1 Centrifuge Tube, cone-shaped, conforming to the di-mensions given in Fig. 1, and made of thoroughly annealedglass.
9、The graduations, numbered as shown in Fig. 1, shall beclear and distinct, and the mouth shall be constructed in a shapesuitable for closure with a cork. Scale-error tolerances andsmallest graduations between various calibration marks aregiven in Table 1 and apply to calibrations made with air-freewa
10、ter at 20 C.5.2 Centrifuge, meeting all the safety requirements fornormal use and capable of whirling two or more filledcentrifuge tubes at a speed which can be controlled to give arelative centrifugal force (rcf) between 600 and 700 at the tipsof the tubes. The revolving head, trunnion rings, and t
11、runnioncups, including the rubber cushion, shall be soundly con-structed to withstand the maximum centrifugal force capable ofbeing delivered by the power source. The trunnion cups andcushions shall firmly support the tubes when the centrifuge isin motion. The centrifuge shall be enclosed by a metal
12、 shield orcase strong enough to eliminate danger if any breakage occurs.Calculate the speed of the rotating head by means of thefollowing equation:speed, r/min 5 1337 =rcf/d (1)where:rcf = relative centrifugal force, andd = diameter of swing, in mm, measured between tips ofopposite tubes when in rot
13、ating position.Table 2 shows the relationship between diameter swing, rcf,and revolutions per minute.1This test method is under the jurisdiction of ASTM Committee D02 onPetroleum Products, Liquid Fuels, and Lubricants and is the direct responsibility ofSubcommittee D02.06 on Analysis of Liquid Fuels
14、 and Lubricants.Current edition approved July 1, 2017. Published July 2017. Originally approvedin 1921. Last previous edition approved in 2012 as D91 02 (2012)1. DOI:10.1520/D0091-02R17.2This test method has been adopted for use by government agencies to replaceMethod 3101 of Federal Test Method Sta
15、ndard No. 791b.3For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor
16、Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations
17、 issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.16. Reagent6.1 Hexanes, Reagent Grade. (WarningExtremelyflammable, harmful if inhaled.)7. Sampling7.1 For sampling techniques, see Practices D4057 or Prac-tice D4177.8. Procedure8.1 Add 10 mL 6 1 mL of the oil to be
18、tested in each of twoclean, dry centrifuge tubes at room temperature. Fill each tubeto the 100 mL mark with hexanes and close tightly with asoftened cork (not a rubber stopper). Then invert each tube atleast 20 times, allowing the liquid to drain thoroughly from thetapered tip of the tube each time.
19、 Place the tubes in a water bathat 32 C to 35 C for 5 min 6 1 min. Momentarily remove thecorks to relieve any pressure, and invert each tube again at least20 times exactly as before. The success of this method dependsto a large degree upon having a thoroughly homogeneousmixture which will drain quic
20、kly and completely from thetapered tip when the tube is inverted.8.2 Balance the two centrifuge tubes or pairs of tubes withtheir respective trunnion cups and place them on opposite sidesof the centrifuge head. Then whirl them for 10 min at a ratesufficient to produce a relative centrifugal force (r
21、cf) between600 and 700 at the tips of the whirling tubes (see 5.2). Repeatthis operation until the volume of sediment in each tuberemains constant for three consecutive readings. In general, notmore than four whirlings will be required for oils having a lowprecipitation number.9. Calculation and Rep
22、ort9.1 Read the volume of the solid sediment at the bottom ofeach centrifuge tube, estimating to 0.1 mL or closer if possible.If the two readings differ by not more than 0.1 mL, report themean of the two as the ASTM Precipitation Number. If the tworeadings differ by more than 0.1 mL, make two more d
23、etermi-nations and report the average of the four determinations.10. Precision and Bias10.1 The precision of this test method as determined bystatistical examination of interlaboratory results is as follows:10.2 RepeatabilityThe difference between two test results,obtained by the same operator with
24、the same apparatus underconstant operating conditions on identical test material, wouldin the long run, in the normal and correct operation of the testmethod, exceed the following values only in one case intwenty:Precipitation Number Repeatability0.00 to 1.20 10 % of Mean10.3 ReproducibilityThe diff
25、erence between two singleand independent results obtained by different operators work-ing in different laboratories on identical test material would, inthe long run, in the normal and correct operation of the testmethod, exceed the following values only in one case intwenty:Precipitation Number Repr
26、oducibility0.00 to 1.20 30 % of Mean10.4 BiasThis procedure is empirical, precipitation num-ber is defined solely by this procedure, therefore, no statementof bias can be made.11. Keywords11.1 asphaltenes; lubricating oils; precipitation numberNOTE 1For volumetric tolerances see Table 1.FIG. 1 ASTM
27、Cone-Shaped Centrifuge TubeTABLE 1 Calibration Tolerances for 200 mm Centrifuge TubeRange, mL Subdivision, mL Volume Tolerance, mL0 to 0.1 0.05 0.02Above 0.1 to 0.3 0.05 0.03Above 0.3 to 0.5 0.05 0.05Above 0.5 to 1.0 0.10 0.05Above 1.0 to 2.0 0.10 0.10Above 2.0 to 3.0 0.20 0.10Above 3.0 to 5.0 0.5 0
28、.20Above 5.0 to 10 1.0 0.50Above 10 to 25 5.0 1.00Above 25 to 100 25 1.00TABLE 2 Rotation Speeds for Centrifuges of Various DiametersDiameter of Swing, mmAr/min at 600 rcf r/min at 700 rcf483 1490 1610508 1450 1570533 1420 1530559 1390 1500AMeasured in millimetres between tips of opposite tubes when
29、 in rotating position.D91 02 (2017)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the ris
30、kof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of thi
31、s standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake
32、your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by
33、contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 02 (2017)3
