1、Designation: D 3006 99 (Reapproved 2004)An American National StandardStandard Specification forPolyethylene Plastic Pressure-Sensitive Electrical InsulatingTape1This standard is issued under the fixed designation D 3006; the number immediately following the designation indicates the year oforiginal
2、adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers electrical insulating tape con-sisting of
3、 a backing made from polyethylene plastic film,coated on one side with a pressure-sensitive adhesive.1.2 The values stated in SI units are the standard. The valuesgiven in parentheses are provided for information purposesonly.2. Referenced Documents2.1 ASTM Standards:2D 1000 Test Methods for Pressur
4、e-Sensitive Adhesive-Coated Tapes Used for Electrical and Electronic Applica-tionsD 1711 Terminology Relating to Electrical Insulation3. Terminology3.1 DefinitionsFor definitions of terms in this specifica-tion refer to Terminology D 1711.4. Material4.1 The backing shall be polyethylene, suitably co
5、m-pounded to meet the requirements of this specification. Thebacking shall be smooth and uniform. The tape edges shall bestraight and unbroken.4.2 The pressure-sensitive coating shall be smooth anduniform, and essentially free from lumps and bare spots. “Fisheyes” shall not be cause for rejection. T
6、here shall be noadhesive transfer when the tape is unwound from the roll.5. Standard Rolls5.1 The standard widths and lengths shall be selected fromthe following:5.1.1 Widths:mm in. mm in.614 1212938 15581934 30 1142278 38 11225 1 50 2Widths greater than 50 mm (2 in.) shall be agreed uponbetween the
7、 purchaser and the seller.5.1.2 Lengths:mft62020 6633 1085.1.3 Nonstandard widths and lengths are permissible ifagreed to between the purchaser and seller.6. Physical Requirements Physical Requirements6.1 The tape shall meet the requirements listed in Table 1.6.2 Black plastic backing shall be consi
8、dered standard.Backing of a different color than black shall be specified on thepurchase order.7. Test Methods7.1 The selection of rolls, conditioning, and testing shall bein accordance with Test Methods D 1000.8. Rejection8.1 If the test results of any roll do not conform to therequirements prescri
9、bed in the specification, two additionalrolls shall be selected and tested. If one of the two additionalsample rolls also does not conform to the requirements, the lotmay be rejected at the option of the purchaser.9. Packaging and Package Marking9.1 PackagingThe package shall withstand shipment ands
10、hall give the product ample protection against damage. Theindividual rolls shall not adhere to each other, or to thecontainer.1This specification is under the jurisdiction of ASTM Committee D09 onElectrical and Electronic Insulating Materials and is the direct responsibility ofSubcommittee D09.07 on
11、 Flexible and Rigid Insulating Materials.Current edition approved March 10, 1999. Published May 1999. Originallyapproved in 1972. Last previous edition approved in 1993 as D 300689 (1993)e1.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at servi
12、ceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.9.2 MarkingEach package shall be marked with the nameof
13、the manufacturer, the manufacturers product number, andthe width and length of the roll.10. Keywords10.1 electrical insulating tape; polyethylene pressure-sensitive tape; pressure-sensitive adhesive tapeASTM International takes no position respecting the validity of any patent rights asserted in con
14、nection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the respon
15、sible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful
16、consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 1
17、00 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM
18、website(www.astm.org).TABLE 1 Requirements for Polyethylene Plastic Electrical TapeThickness, mm (in.) avg 0.241 6 0.025 (0.0095 6 0.0010)Width, as specified, mm (in.) 6 0.8 (132)Length, as specified, min, mm or m (ft oryd)minus 1 %Breaking strength, min, kN/m (lbf/in.) avg 2.8 (16)Elongation, min,
19、% avg 150Dielectric breakdown, min, V avgStandard condition 10 000Wet condition (96/23/96) 90 % of avg value obtained understandard conditionAdhesion, min, N/m (ozf/in.) avgASteel 175 (16)Backing 175 (16)Backing at 7 C 175 (16)Unwind at 7 C, N/m (ozf/in.), avgBMin 175 (16)Max 1400 (128 )Static elongation at 7 C, min, % avg 15Penetration, min, C avg 45High-humidity insulation resistance, min,MV median1 3 105Flagging, max, mm (in.), avg 13 (0.5)ASee Test Methods D 1000, Test Method A.BSee Test Methods D 1000, Test Method B.D 3006 99 (2004)2
