ASTM D3325-1990(2013) Standard Practice for Preservation of Waterborne Oil Samples《水中油样品保存的标准实施规程》.pdf
《ASTM D3325-1990(2013) Standard Practice for Preservation of Waterborne Oil Samples《水中油样品保存的标准实施规程》.pdf》由会员分享,可在线阅读,更多相关《ASTM D3325-1990(2013) Standard Practice for Preservation of Waterborne Oil Samples《水中油样品保存的标准实施规程》.pdf(3页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D3325 90 (Reapproved 2013)Standard Practice forPreservation of Waterborne Oil Samples1This standard is issued under the fixed designation D3325; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision
2、. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This practice covers the preservation of waterborne oilsamples from the time of collection to the time of analysis.Information is
3、provided to ensure sample integrity and to avoidcontamination and to minimize microbial degradation.1.2 The practice is for controlled field or laboratory condi-tions and specifies thorough preparation of equipment andprecise operation. Where these details must be compromised ina field emergency, no
4、nstandard simplifications are recom-mended that will minimize or eliminate consequent errors.NOTE 1Procedures for the analysis of oil spill samples are PracticesD3326, D3415, D3650, and D4489, and Test Methods D3327, D3328, andD3414. A guide to the use of ASTM test methods for the analysis of oilspi
5、ll samples is found in Practice D3415.1.3 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory li
6、mitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D1129 Terminology Relating to WaterD3326 Practice for Preparation of Samples for Identificationof Waterborne OilsD3327 Method for Analysis of Selected Elements in Wart-erborne Oils3D3328 Test Methods for Comparison of Waterborne Petro
7、-leum Oils by Gas ChromatographyD3414 Test Method for Comparison of Waterborne Petro-leum Oils by Infrared SpectroscopyD3415 Practice for Identification of Waterborne OilsD3650 Test Method for Comparison of Waterborne Petro-leum Oils By Fluorescence AnalysisD4489 Practices for Sampling of Waterborne
8、 Oils3. Terminology3.1 DefinitionsFor definitions of terms used in thispractice, refer to Terminology D1129.4. Summary of Practice4.1 Special types of sample containers and shipping con-tainers are recommended. Samples may be of several types: tarballs, collected oil, oil-water mixtures, emulsions,
9、and oil andwater on collecting devices such as silanized glass cloth,TFE-fluorocarbon polymer, or other materials. Instructions aregiven for the care of samples to minimize changes due toautoxidation and microbial attack between the time of sam-pling and the time of analysis. Services available for
10、transpor-tation of samples are described.5. Apparatus5.1 Sample ContainersBorosilicate glass containers thathave been thoroughly cleaned are preferable. All glasscontainers, new or used, must be thoroughly cleaned andwashed prior to use. The cleaning steps consist of an initialwash with a warm aqueo
11、us detergent mixture followed by sixhot tap water rinses, two rinses with reagent water, a rinse withreagent-grade acetone, and a final rinse with a solvent such aspentane, hexane, cyclohexane, dichloromethane, or chloroformfollowed by drying in a clean oven at 105C or hotter for 30min. If the glass
12、ware requires cleaning under field conditions,it should be washed with warm aqueous detergent followed byextensive water rinsing. A solvent rinse with acetone should bemade, if possible, followed by lengthy air drying to removeresidual solvent. (WarningFor safety reasons, the use ofpentane, hexane,
13、or cylcohexane is recommended over use ofdichloromethane or carbon tetrachloride. )NOTE 2Hot reagent water rinses are advisable where hot tap watermight reintroduce contamination.5.1.1 Plastic containers are not acceptable since volatilehydrocarbons diffuse readily through many commercial plasticcon
14、tainers or may be absorbed into the plastic. In addition, theplasticizer may dissolve in the sample causing misleadingresults.1This practice is under the jurisdiction of ASTM Committee D19 on Water andis the direct responsibility of Subcommittee D19.06 on Methods for Analysis forOrganic Substances i
15、n Water.Current edition approved Feb. 15, 2013. Published March 2013. Originallyapproved in 1974. Last previous edition approved in 2002 as D3325 90 (2006).DOI: 10.1520/D3325-90R13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.or
16、g. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. Unit
17、ed States15.1.2 Metal containers usually should be avoided becausethe nickel and vanadium determinations could be invalidatedby introduction of metal from the can.5.1.3 When field expedients must be employed, an emptycontainer of each type used should be included in the shipmentto the laboratory to
18、be used as a blank to measure inadvertentcontamination.5.2 ClosuresProper choice of closures is critical to avoidcontamination and to preserve sample. Use caps withaluminum-coated or TFE-fluorocarbon-coated cardboard in-serts. Aluminum foil sheet should not be used. Inserts ofTFE-fluorocarbon sheet,
19、 however, are acceptable.5.3 Refrigerator, explosion-proof at about 4 to 5C.5.4 Shipping ContainersSturdy cartons or wooden boxesshould be used. These should be sufficiently large so thesample containers are adequately surrounded by absorbentpacking material, such as vermiculite, sufficient to absor
20、b theentire contents should breakage occur and be lined with agrease proof plastic bag.NOTE 3After Dec. 31, 1990, packagings used for shipment ofdangerous goods such as oil must be tested for compliance with UNPerformance Packaging Standards and certified by a marking applied bythe packaging manufac
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD332519902013STANDARDPRACTICEFORPRESERVATIONOFWATERBORNEOILSAMPLES 水中 样品 保存 标准 实施 规程 PDF

链接地址:http://www.mydoc123.com/p-514565.html