ASTM D3679-2017 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding《硬质聚氯乙烯(PVC)壁板的标准规格》.pdf
《ASTM D3679-2017 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding《硬质聚氯乙烯(PVC)壁板的标准规格》.pdf》由会员分享,可在线阅读,更多相关《ASTM D3679-2017 Standard Specification for Rigid Poly(Vinyl Chloride) (PVC) Siding《硬质聚氯乙烯(PVC)壁板的标准规格》.pdf(14页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: D3679 13D3679 17 An American National StandardStandard Specification forRigid Poly(Vinyl Chloride) (PVC) Siding1This standard is issued under the fixed designation D3679; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision,
2、 the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This specification establishes requirements and test methods for the materials, dimensions, warp, shrink
3、age, impact strength,expansion, appearance, and windload wind load resistance of extruded single-wall siding manufactured from rigid (unplasticized)PVC compound. Methods of indicating compliance with this specification are also provided.1.2 The use PVC recycled plastic in this product shall be in ac
4、cordance with the requirements in Section 4.1.3 Rigid (unplasticized) PVC soffit is covered in Specification D4477.1.4 Siding produced to this specification shall be installed in accordance with Practice D4756. Reference shall also be made tothe manufacturers installation instructions for the specif
5、ic product to be installed.NOTE 1Information with regard to siding maintenance shall be obtained from the manufacturer.1.5 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information o
6、nly and are not considered standard.1.6 The following precautionary caveat pertains to the test method portion only, Section 6, of this specification:This standarddoes not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of thisstan
7、dard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.NOTE 2There is no known ISO equivalent to this standard.1.7 This international standard was developed in accordance with internationally recognized principles on standardi
8、zationestablished in the Decision on Principles for the Development of International Standards, Guides and Recommendations issuedby the World Trade Organization Technical Barriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2D618 Practice for Conditioning Plastics for TestingD
9、635 Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal PositionD696 Test Method for Coefficient of Linear Thermal Expansion of Plastics Between 30C and 30C with a Vitreous SilicaDilatometerD883 Terminology Relating to PlasticsD1042 Test Method for Linear Di
10、mensional Changes of Plastics Caused by Exposure to Heat and MoistureD1435 Practice for Outdoor Weathering of PlasticsD1600 Terminology for Abbreviated Terms Relating to PlasticsD2244 Practice for Calculation of Color Tolerances and Color Differences from Instrumentally Measured Color CoordinatesD24
11、57 Test Method for Specular Gloss of Plastic Films and Solid PlasticsD3892 Practice for Packaging/Packing of PlasticsD4226 Test Methods for Impact Resistance of Rigid Poly(Vinyl Chloride) (PVC) Building ProductsD4477 Specification for Rigid (Unplasticized) Poly(Vinyl Chloride) (PVC) SoffitD4756 Prac
12、tice for Installation of Rigid Poly(Vinyl Chloride) (PVC) Siding and SoffitD5033 Guide for Development of ASTM Standards Relating to Recycling and Use of Recycled Plastics (Withdrawn 2007)31 This specification is under the jurisdiction of ASTM Committee D20 on Plastics and is the direct responsibili
13、ty of Subcommittee D20.24 on Plastic Building Products.Current edition approved Nov. 1, 2013June 1, 2017. Published November 2013July 2017. Originally approved in 1979. Last previous edition approved in 20112013 asD3679 11.D3679 13. DOI: 10.1520/D3679-13.10.1520/D3679-17.2 For referencedASTM standar
14、ds, visit theASTM website, www.astm.org, or contactASTM Customer Service at serviceastm.org. For Annual Book of ASTM Standardsvolume information, refer to the standards Document Summary page on the ASTM website.3 The last approved version of this historical standard is referenced on www.astm.org.Thi
15、s document is not an ASTM standard and is intended only to provide the user of an ASTM standard an indication of what changes have been made to the previous version. Becauseit may not be technically possible to adequately depict all changes accurately, ASTM recommends that users consult prior editio
16、ns as appropriate. In all cases only the current versionof the standard as published by ASTM is to be considered the official document.*A Summary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959.
17、United States1D5206 Test Method for Windload Resistance of Rigid Plastic SidingD5947 Test Methods for Physical Dimensions of Solid Plastics SpecimensE631 Terminology of Building ConstructionsE1753 Practice for Use of Qualitative Chemical Spot Test Kits for Detection of Lead in Dry Paint FilmsG147 Pr
18、actice for Conditioning and Handling of Nonmetallic Materials for Natural and Artificial Weathering Tests2.2 ASCE Standard:ASCE 7-02ASCE 7-10 Minimum Design Loads for Buildings and Other Structures42.3 International Code Council:5International Building CodeInternational Residential Code2.4 Vinyl Sid
19、ing Institute, Inc.:6VSI Vinyl Siding Installation Manual (2015)2.5 Structural Building Components Association:7ANSI/SBCA FS 100-2012 Standard Requirements for Wind Pressure Resistance of Foam Plastic Insulating Sheathing Used inExterior Wall Covering Assemblies3. Terminology3.1 Definitions are in a
20、ccordance with Terminologies D883, E631, and D1600, unless otherwise specified.3.2 Definitions of Terms Specific to This Standard:3.2.1 center-pinningan installation technique in which the siding panel is fastened tightly through the nail slot at the centerlength of the panel, in order to cause ther
21、mal expansion and contraction to occur equally in both directions from the center.3.2.2 heavily textured sidingin this standard, any vinyl siding using separate postextrusion processing to produce a texturedsurface.3.2.2.1 DiscussionPost-extrusion-forming does not include embossing of the surface or
22、 forming of the faces of the profile, but does include suchprocesses as heat forming, vacuum forming and compression molding applied to the surface after the profile is extruded.3.2.3 nominalthe value that a manufacturer consistently uses to represent a specific property or dimension of a vinyl sidi
23、ngproduct in public claims including, but not limited to, product literature, advertisements, quotations, and certificates ofconformance.3.2.4 process average thicknessthe rolling, arithmetic mean of average specimen thicknesses measured according to 6.5 fora specific product during all productions
24、runs for the most recent six month period.3.2.5 temperate northern climatein weather testing, a North American metropolitan area testing site located within 73 to100W longitude and 37 to 45N latitude.3.2.6 wind load design pressure ratingthe maximum wind pressure that a vinyl siding product is rated
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMD36792017STANDARDSPECIFICATIONFORRIGIDPOLYVINYLCHLORIDEPVCSIDING 硬质 聚氯乙烯 PVC 壁板 标准 规格 PDF

链接地址:http://www.mydoc123.com/p-515254.html