1、Designation: D 3720 90 (Reapproved 2005)Standard Test Method forRatio of Anatase to Rutile in Titanium Dioxide Pigments byX-Ray Diffraction1This standard is issued under the fixed designation D 3720; the number immediately following the designation indicates the year oforiginal adoption or, in the c
2、ase of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method covers the determination of the ratio ofanatase to rutile in titanium d
3、ioxide pigments. The method isalso applicable to pigment mixtures and pigmented coatingscontaining titanium dioxide.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 This standard does not purport to address all of thesaf
4、ety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 215 Practice for the Chemical
5、 Analysis of White LinseedOil PaintsD 2371 Test Method for Pigment Content of Solvent-Reducible PaintsD 2698 Test Method for Determination of the PigmentContent of Solvent-Reducible Paints by High Speed Cen-trifugingD 3925 Practice for Sampling Liquid Paints and RelatedPigmented Coatings3. Summary o
6、f Test Method3.1 The X-ray diffraction pattern obtained from a material ischaracteristic of that material. The intensity of a diffractionpeak entirely due to one component of a mixture is dependentupon the amount of that substance in the mixture. To a minorextent the peak intensity of the component
7、is also dependent onthe mass absorption coefficient of other materials present.Since the test method utilizes the ratio of the intensities ofdiffraction peaks of two chemically similar materials, it isexpected that the effects of other constituents will be the samefor both materials.3.2 The intensit
8、y of the diffraction maxima for anatase andrutile is measured by X-ray diffractometry. The intensity of theanatase peak is converted to anatase content relative to rutileand the rutile content is determined by difference.3.3 The X-ray diffraction measurement is made on singlepigments, pigment mixtur
9、es, films of pigmented coatings, andfilms prepared from liquid coatings, if interfering materials arenot present. When interfering materials are present, the pig-ment is separated from the redissolved (or ignited film, or fromthe liquid coating and treated to isolate the titanium dioxide.4. Signific
10、ance and Use4.1 This test method is used by titanium dioxide pigmentmanufacturers and users for process control and productacceptance.5. Interferences5.1 Calcium sulfate interferes, but its effect is eliminated bychemical removal (see Practice D 215). It is desirable to assureby analysis that any re
11、sidual CaSO4is considerably less thanthe level of anatase being sought. The insoluble residue afterremoval of calcium sulfate should be ignited above 700C.Chrome yellow and the valentinite form of antimony trioxidealso interfere if not removed. High amounts of iron renderanalysis difficult due to in
12、creased background (see Note 1).Additives, such as antimony and zinc, and impurities, such asniobium and zirconium, are generally present in solid solutionand thus would not have interfering diffraction peaks. Surfacetreatments such as silica and alumina do not interfere. Extremedifferences in parti
13、cle size between the anatase and rutileportions affect the results.NOTE 1Background scatter due to high iron levels in a sample may bereduced by use of a cobalt or molybdenum target tube in place of thecopper target tube. The background may be eliminated for all practicalpurposes by use of a curved
14、crystal monochromator equipped with agraphite crystal in conjunction with a copper target tube.5.2 In the calculation of converting the ratio to percent it isimplicitly assumed that the sum of anatase and rutile is 100 %,an assumption normally made in TiO2pigment systems. Othermaterials present woul
15、d interfere to the extent that they dilute1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.31 on Pigment Specifications.Current edition approved July 1, 2005. Published Augu
16、st 2005. Originallyapproved in 1978. Last previous edition approved in 1999 as D 3720 - 90 (1999).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Docu
17、ment Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.the sample. The third polymorphic form of TiO2, brookite,would have such an effect. However, it reportedly does notoccur in commercial titanium diox
18、ide pigments.6. Apparatus6.1 X-Ray DiffractometerThe principle components ofthis instrument are: (a) X-ray generator, (b) copper target X-raytube, (c) goniometer, (d) detector, (e) electronic circuit panel,(f) computer (if used), and (g) strip chart recorder or printer.6.2 Operating ConditionsThe X-
19、ray tube voltage andfilament current and other settings are selected to record X-raydiffraction peaks of weak intensities.6.2.1 Nickel Filter, to remove Cu K beta radiation if amonochromator is not used. Cu K beta radiation will producea diffraction line from the rutile phase of TiO2that appears att
20、he same 2u angle as the anatase analytical line.6.3 Typical Apparatus Conditions:6.3.1 High-Voltage Power SupplySelect X-ray tube volt-age, filament current, and other settings so that 0.1 % anatasegenerates a signal with intensity at least four times the noiselevel.6.3.2 DetectorScintillation detec
21、tor operating at optimumvoltage.6.3.3 Pulse Height AnalyzerSettings will depend on in-strumentation used.6.3.4 SlitsReceiving slit, 0.15; others, 1.6.3.5 Chart Speed, 12.5 mm (12 in.)/min.6.3.6 Goniometer Speed,14 /min, scanning or 0.02 stepswith 4.8 s per step.6.3.7 Time Constant,5.6.3.8 Scanning R
22、ange,2u = 28 to 24.6.3.9 Scale FactorsFor samples of low anatase content ascale factor of 100 counts full scale is normally used for the2u = 26 to 24 range (anatase diffraction maximum), and ascale factor of 5000 counts full scale is normally used for the2u = 28 to 26 range (rutile diffraction maxim
23、um). The scalefactors may be changed depending on the level of anataseexpected in the sample.7. Reagents7.1 Purity of ReagentsUntreated rutile and anatase gradesof titanium dioxide pigments are used to make syntheticstandards for calibration. The crystalline structures of thereagents must be 100 % r
24、utile and 100 % anatase as determinedby examining these materials by X-ray diffraction to assure thispurity.7.2 Mixing ReagentsA series of rutile standards of vary-ing rutile content are prepared to cover the range of interest bythoroughly mixing known amounts of 100 % rutile and 100 %anatase togeth
25、er. The pigments are dispersed in a solvent suchas isopropyl alcohol and then mixed, followed by air drying.This dry cake is ground up using a mortar and pestle to ensurehomogeneity.8. Hazards8.1 X-ray producing equipment can be dangerous to boththe operator and persons in the immediate vicinity unl
26、ess safetyprecautions are strictly observed. Refer to the manufacturersinstruction manual. Exposure to excessive quantities ofX-radiation may be injurious to health. Therefore, users shouldavoid exposing any parts of their bodies, not only to the directbeam, but also to secondary or scattered radiat
27、ion that occurswhen an X-ray beam strikes or has passed through anymaterial. It is strongly recommended that users check thedegree of exposure by film carried on them or by the use ofdosimeters and that blood counts be made periodically. Beforeutilizing the equipment, all persons designated or autho
28、rized tooperate X-ray instrumentation or supervise its operation,should have a full understanding of its nature and should alsobecome familiar with established safe exposure factors by acareful study of the National Bureau of Standards Handbook“X-Ray Recommendations of the International Roentgen Ray
29、Committee on X-Ray Protection” and other standard publica-tions on the subject. Inquiries should be made of state agenciesas to existing requirements.9. Specimen Preparation9.1 Powder Samples:9.1.1 Packing the specimen in the specimen holder to obtaina planar surface is one of the most important pha
30、ses in X-rayanalysis. Ripples or indentures in the specimen surface causevariations in the test because of an error of eccentricity and achange in the intensities of the peaks. The chance of preferredorientation of pigmentary TiO2is remote because of its smallparticle size.9.1.2 Pack the specimen in
31、 a die suitably constructed toaccommodate the specimen holder for the goniometer. Applyconstant pressure with a hydraulic press (see Note 2). Alterna-tively, place the specimen holder on a flat, smooth firm surfaceand pack the specimen into the opening by applying constantand firm pressure with a fl
32、at blade. The possibility of variationsamong different bags of the same lot should be considered.NOTE 2Use of a set procedure with a hydraulic press will improvespecimen preparation uniformity compared to hand-packed specimens.This is particularly true where more than one person is involved inspecim
33、en preparation.9.2 Coatings on Metal Panels:9.2.1 Cut the coated panel into the proper shape and size tofit an adjustable specimen holder and analyze without furtherpreparation. This assumes that interferences are not present(see Section 5).9.3 Liquid Coating Samples:9.3.1 Sample material in accorda
34、nce with Practice D 3925.9.3.2 Liquid coating samples without interfering materialspresent (see Section 5) are analyzed as cast films of the totalpaint on aluminum or other suitable substrate.A25 to 50-m (1to 2-mil) dry film thickness is adequate.9.3.3 Liquid paint samples with interfering materials
35、present (see Section 4) must not be analyzed until the interfer-ing components are removed. This can be accomplished bycentrifuging (Test Methods D 2371 or D 2698) to separate thetotal pigment. The separated pigment is treated according tothe Insoluble Matter section of Practice D 215 to obtaininter
36、ference-free TiO2. Quantitative results are not required foreither separation procedure.D 3720 90 (2005)210. Procedure10.1 Record the X-ray diffraction maxima of the anataseand of the rutile peak by scanning the range between 2u =26to 24 and 2u = 28 to 26, respectively. Scan each range twice.10.2 Dr
37、aw the baseline between the lowest points of thetrace on each side of the peak. Measure the peak height abovethe baseline expressed in chart units, centimetres, counts persecond, or other convenient units for the anatase and rutilepeaks. Average the net peak heights of the duplicate runs.10.3 Since
38、only ratios are used, the peak heights need onlybe corrected for differences, if any, in the scale factors used forthe two peaks.Any consistent units can be used, not just countsper second.10.4 Prior to and after analyzing the unknown sample,analyze one of the standards to verify instrument stabilit
39、y.11. Calculations11.1 Determine the value of the constant, K, as followsK 5 Ia/Ir!/Wa/Wr!where:Ia= net intensity of the anatase diffraction peak,Ir= net intensity of the rutile diffraction peak,Wa= weight of anatase, andWr= weight of rutile.11.1.1 K is equal to the slope of a calibration plot obtai
40、nedwhen the intensity ratio Ia/Iris plotted as a function of Wa/Wr,using data derived from a series of standards that span theconcentration range of interest. Routine calibration proceduresare followed.3,4NOTE 3The value of K is influenced by the instrument conditionsselected in Section 5. Data for
41、standards and test samples must becollected using the same conditions.11.2 Calculate the anatase level relative to rutile from thepeak intensities above background as follows:Percent anatase 511 1 KIrIa3 10012. Precision12.1 On the basis of an interlaboratory test of this testmethod in which four op
42、erators in four laboratories tested twomaterials with composition approaching 100 or 0 % anatase orrutile, the within-laboratory standard deviation was found to be0.06 % for a single determination. The between-laboratoriesstandard deviation was found to be 0.07 % absolute for resultseach the mean of
43、 two determinations. Based on these standarddeviations, the following criteria should be used for judging theprecision of results at the 95 % confidence level.12.1.1 RepeatabilityTwo results obtained by the sameoperator should be considered suspect if they differ by morethan 0.18 % absolute for mate
44、rials approaching 100 or 0 %.12.1.2 ReproducibilityTwo results, each the mean of twodeterminations, obtained by operators in different laboratoriesshould be considered suspect if they differ by more than 0.22 %absolute for materials approaching 100 or 0 %.13. Keywords13.1 anatase pigment analysis; r
45、utile; titanium oxide analy-sis; X-ray diffraction.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent righ
46、ts, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for
47、revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing
48、you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may
49、be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).3Myers, H. and Spurr, R., Analytical Chemistry, Vol 29, 1957, p. 760.4Zingaro, P. W., Norelco Reporter, Vol 5, No. 56.D 3720 90 (2005)3
