1、Designation: D 4286 90 (Reapproved 1999)Standard Practice forDetermining Coating Contractor Qualifications for NuclearPowered Electric Generation Facilities1This standard is issued under the fixed designation D 4286; the number immediately following the designation indicates the year oforiginal adop
2、tion or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice provides a criteria guide and proceduralmethod to assist
3、utility owners, architects, engineers, construc-tors, and other selection agencies in determining the overallqualifications of a coating contractor to execute coating workfor the primary containment and other safety-related facilitiesof light-water nuclear power plants.1.2 The qualification criteria
4、 and requirements address theessential basic capability of a contractor to execute nuclearcoating work. Obviously, the specific capability to executethose requirements unique to a given project must also becarefully considered. The evaluation procedure contained inthis practice is designed to be ada
5、ptive to this detailed finalqualification process. Variation or simplification of the practiceis appropriate for non safety-related areas of nuclear powerplants, fossil fueled facilities, and other industrial projects.1.3 The overall capability of a contractor to successfullyexecute the varied and c
6、omplex requirements of nuclearcoating work is dependent upon competency in a variety ofessential categories.1.4 The nine evaluation categories described in Sections3-12 detail the specific data to be provided by the contractor asessential to determining qualification status. In addition, a tenthunti
7、tled category has been provided on the evaluation workdescribed in Section 12 for inclusion of other informationpertinent to a specific project.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standa
8、rd to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:D 3843 Practice for Quality Assurance for Protective Coat-ings Applied to Nuclear Facilities2D 4537 Guide for Establishing Proced
9、ures to Qualify andCertify Inspection Personnel for Coating Work in NuclearFacilities22.2 American National Standard:N 45.2.6 Qualifications of Inspection, Examination, andTesting Personnel for Nuclear Power Plants32.3 Other Standard:Nuclear Regulatory Agency 10 CFR 50 Appendix B, Qual-ity Assurance
10、 Criteria for Nuclear Power Plants43. Personnel3.1 Home Offce Management and StaffResumes of thefollowing types of personnel including educational back-ground, duration and degree of involvement in industrialcoating operations, qualifications, registrations, certifications,and specific experience in
11、 nuclear coating work.3.1.1 Principals and General Management.3.1.2 Engineering Manager.3.1.3 Project EngineersList specific nuclear coating workproject involvement.3.1.4 QA/QC ManagerList specific qualification/certification credentials per ANSI N 45.2.6, or Guide D 4537,or both.3.2 General Field S
12、upervisionResumes to include spe-cific nuclear coatings work experience.3.3 On-Site Project Supervision:3.3.1 Total number of personnel qualified for nuclear coat-ings work, including specific work history.3.3.2 Total number available in a specific time frame, ifappropriate.4. Contractor Work Experi
13、ence4.1 General ExperienceList of comparable industrialprojects, including type (construction or maintenance), form ofcontract, dollar volume, scope, and duration (start and comple-tion dates) executed during the past five years. Accompanyingthis listing provide personnel references to include names
14、,titles, locations, and telephone numbers.4.2 Nuclear Coating Work Experience:4.2.1 List of nuclear projects including type (construction or1This practice is under the jurisdiction of ASTM Committee D33 on ProtectiveCoating and Lining Work for Power Generation Facilities and is the directresponsibil
15、ity of Subcommittee D33.05 on Application and Surface Preparation.Current edition approved March 30, 1990. Published May 1990. Originallypublished as D 4286 84. Last previous edition D 4286 84.2Annual Book of ASTM Standards, Vol 06.02.3Available from American National Standards Institute, 11 W. 42nd
16、 St., 13thFloor, New York, NY 10036.4Available from Superintendent of Documents, U.S. Government PrintingOffice, Washington, DC 20402.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.maintenance), form of contract, dollar volume, scop
17、e, andduration, materials, and equipment involved. Accompanyingthis listing provide personnel references to include names,titles, locations, and telephone numbers.4.2.2 If the contractor has executed work comparable to thespecific evaluation project, submit complete case histories ofscope and functi
18、ons performed to include personnel referencesfor each case.5. Equipment5.1 List contractor-owned equipment in the categories listedin 5.1.1-5.1.9. Indicate those items required for the specificevaluation project.5.1.1 Vehicles.5.1.2 Surface preparation, all types.5.1.3 Abrasive control and recovery.
19、5.1.4 Coatings mixing and application, all types.5.1.5 Environmental control and curing.5.1.6 Rigging and enclosure.5.1.7 Safety.5.1.8 Quality control testing instrumentation.5.1.9 Specialized equipment.5.1.9.1 Unique equipment required for the specific project,if applicable.5.1.9.2 Contractor to in
20、dicate and provide examples ofcapability to design and install highly specialized items ofequipment, enclosure systems, devices, etc. which have beenutilized on previous nuclear coating projects.5.1.10 Equipment Repair and Replacement CapabilityContractor to describe standard procedure followed in t
21、heevent of equipment failure to prevent lost time situations.6. Quality Assurance6.1 Quality Assurance ProgramThe contractor shall sub-mit one copy of his quality assurance program that shallconform to 10 CFR 50 Appendix B, ANSI N 45.2.6, GuideD 4537, Practice D 3843, and other applicable documents.
22、 Theprogram shall include implementation procedures and sampleforms.6.2 Quality Assurance/Quality ControlList number ofpersonnel qualified in accordance with ANSI N 45.2.6 or GuideD 4537, or both, for each of the following:6.2.1 LEVEL III Inspector,6.2.2 LEVEL II Inspector, and6.2.3 LEVEL I Inspecto
23、r.7. Training7.1 Submit training manual for craft and supervisory per-sonnel. If no formal training program exists, the contractorshall submit evidence of procedures and methods utilized.8. Safety8.1 Submit copy of corporate safety program. If no formalprogram exists, the contractor shall submit evi
24、dence of safetyprocedures and work rules.9. Production/Cost Control9.1 Submit explanation of methods and procedures utilizedto monitor and regulate personnel and equipment productivity.9.2 Submit sample of actual report forms utilized to recordjob progress, labor cost analysis, and equipment deploym
25、entefficiency.10. Financial10.1 Submit documentation to verify financial capability tomanage and execute all project requirements. Include thefollowing data:10.1.1 Current financial statement,10.1.2 Trade references, three or more,10.1.3 Bank references, one or more,10.1.4 Bonding capacity, name of
26、bonding company, andname and address of agent, and10.1.5 Current certificate of insurance.11. Current and Projected Performance Capability(restricted to specific project considerations)11.1 Submit a statement indicating current commitmentstatus of personnel, equipment, and management capability.The
27、statement shall include analysis of and ability to fulfillrequirements in the following categories:11.1.1 Craft personnel,11.1.2 Staff engineering and supervisory personnel,11.1.3 Management personnel,11.1.4 Equipment, and11.1.5 Materials.12. Contractor Evaluation Work Sheet12.1 The sample work shee
28、t shown in Fig. 1 is suggested forconsolidation of rating and comparison data. Note that thereare nine basic rating categories corresponding to the criteriadetailed in the text of this practice. Space for an optional tenthcategory has been provided for owner insertion of other ratingdata that may be
29、 unique to the specific project involved.12.2 Rating ValuesNumerical rating values are structuredon the following format:Rating ValueExcellent 4Good 3Average 2Poor 1Unsatisfactory 0No data 012.3 Weighted Category ValuesEach of the ten (includesoption) evaluation categories will be assigned a weighte
30、d valueby the owner in accordance with the specific requirements ofthe project. The value scale will range from 1 (least critical) to10 (most critical). The weighted value of each category will beused as a multiplier to determine the overall rating for eachcontractor in each category.13. Keywords13.
31、1 evaluation categories; productivity; qualification crite-ria; quality assurance; work experienceD 42862ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that
32、 determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapprov
33、ed or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you fee
34、l that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).FIG. 1 Contractor Evaluation Work SheetD 42863
