1、Designation: D5451 93 (Reapproved 2012)Standard Practice forSampling Using a Trier Sampler1This standard is issued under the fixed designation D5451; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numb
2、er in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers sampling using a trier. A trierresembles an elongated scoop as shown in Fig. 1. The trier isused to collect samples of
3、 granular or powdered materials thatare moist or sticky and have a particle diameter less thanone-half the diameter of the trier.1.2 The trier can be used as a vertical coring device onlywhen it is certain that a relatively complete and cylindricalsample can be extracted.1.3 This standard does not p
4、urport to address all of thesafety problems, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2
5、D4687 Guide for General Planning of Waste SamplingD5088 Practice for Decontamination of Field EquipmentUsed at Waste SitesD5283 Practice for Generation of Environmental Data Re-lated to Waste Management Activities: Quality Assuranceand Quality Control Planning and Implementation3. Summary of Practic
6、e3.1 As a coring device, the trier is pushed into the materialto be sampled and is turned to cut the core. The core is thenremoved from the hole.4. Significance and Use4.1 This practice is applicable to sampling soils and similarfine-grained cohesive materials. This practice is to be used bypersonne
7、l who are to acquire the samples.4.2 This practice should be used in conjunction with GuideD4687, which covers sampling plans, safety, quality assurance,preservation, decontamination, labeling, and chain-of-custodyprocedures; Practice D5088, which covers the decontaminationof field equipment used at
8、 waste sites; and Practice D5283,which covers project specifications and practices for environ-mental field operations.5. Sampling Equipment5.1 The trier should be made from materials that arecompatible with the substances being sampled and with thetests or analyses to be performed. Either stainless
9、 steel orpolytetrafluoroethylene-coated metal will be suitable for mostsituations (see Fig. 1).6. Sample Containers6.1 Plastic, glass, or other nonreactive containers should beused. Refer to Guide D4687 for further information on con-tainers.1This practice is under the jurisdiction of ASTM Committee
10、 D34 on WasteManagement and is the direct responsibility of Subcommittee D34.01.03 onSampling Equipment.Current edition approved Sept. 1, 2012. Published December 2012. Originallyapproved in 1993. Last previous edition approved in 2008 as D5451-93(2008). DOI:10.1520/D5451-93R12.2For referenced ASTM
11、standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.FIG. 1 Triers (Typical)1Copyright ASTM International, 100 Barr Harbor Drive, PO Bo
12、x C700, West Conshohocken, PA 19428-2959, United States.7. Procedure7.1 Record appropriate information and observations on thesample location.7.2 If sampling soils, remove surface vegetation or debris,or both, from the area of sample extraction.7.3 For core sampling, proceed as follows:7.3.1 Insert
13、the trier approximately perpendicular to thesurface of the material and rotate (one or two times) to cut acore.7.3.2 Pull the core out of the hole slowly. Do not allowadditional overburden material to become part of the sample.Inspect the core surface, and note the appearance of anyirregularities (f
14、or example, scratches, pock marks, andpebbles). Also inspect the core for breakage. If breakage hasoccurred and the core does not satisfy minimum lengthrequirements, discard it and extract another from an immedi-ately adjacent location.7.4 Transfer the sample into a suitable container using aclean s
15、patula. Seal the container and affix a label.7.5 Complete the field logbook and chain-of-custody forms.7.6 Decontaminate the used equipment in accordance withPractice D5088.8. Keywords8.1 sampling; soil sampling; trier; wasteASTM International takes no position respecting the validity of any patent
16、rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at
17、any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments
18、 will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by
19、 ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).D5451 93 (2012)2
