ASTM D5677-2016 6973 Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings Adhesive Bonded Joint Type for Aviation Jet Turbine F.pdf

上传人:unhappyhay135 文档编号:520418 上传时间:2018-12-03 格式:PDF 页数:6 大小:97.34KB
下载 相关 举报
ASTM D5677-2016 6973 Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings Adhesive Bonded Joint Type for Aviation Jet Turbine F.pdf_第1页
第1页 / 共6页
ASTM D5677-2016 6973 Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings Adhesive Bonded Joint Type for Aviation Jet Turbine F.pdf_第2页
第2页 / 共6页
ASTM D5677-2016 6973 Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings Adhesive Bonded Joint Type for Aviation Jet Turbine F.pdf_第3页
第3页 / 共6页
ASTM D5677-2016 6973 Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings Adhesive Bonded Joint Type for Aviation Jet Turbine F.pdf_第4页
第4页 / 共6页
ASTM D5677-2016 6973 Standard Specification for Fiberglass (Glass-Fiber-Reinforced Thermosetting-Resin) Pipe and Pipe Fittings Adhesive Bonded Joint Type for Aviation Jet Turbine F.pdf_第5页
第5页 / 共6页
亲,该文档总共6页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation: D5677 16 An American National StandardStandard Specification forFiberglass (Glass-Fiber-Reinforced Thermosetting-Resin)Pipe and Pipe Fittings, Adhesive Bonded Joint Type, forAviation Jet Turbine Fuel Lines1This standard is issued under the fixed designation D5677; the number immediately

2、 following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope*1.1 This speci

3、fication covers a reinforced plastic pipe andfittings system made from epoxy resin and glass-fiberreinforcement, together with adhesive for joint assembly,intended for service up to 150F (65.6C) and 150-psig(1034-kPa) operating pressure and surges up to 275 psig (1896kPa) in aviation jet turbine fue

4、l lines installed below ground.1.2 The dimensionless designator NPS has been substitutedin this specification for such traditional terms as nominaldiameter, size, and nominal size.1.3 The values stated in inch-pound units are to be regardedas standard. The values in parentheses are for information o

5、nly.1.4 The following safety hazards caveat pertains only to thetest method portion, Section 9, of this specification:Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate saf

6、ety and healthpractices and determine the applicability of regulatory limita-tions prior to use.NOTE 1There is no known ISO equivalent to this standard.2. Referenced Documents2.1 ASTM Standards:2D381 Test Method for Gum Content in Fuels by Jet Evapo-rationD883 Terminology Relating to PlasticsD1599 T

7、est Method for Resistance to Short-Time HydraulicPressure of Plastic Pipe, Tubing, and FittingsD1600 Terminology forAbbreviated Terms Relating to Plas-ticsD1655 Specification for Aviation Turbine FuelsD2310 Classification for Machine-Made “Fiberglass”(Glass-Fiber-Reinforced Thermosetting-Resin) Pipe

8、D2412 Test Method for Determination of External LoadingCharacteristics of Plastic Pipe by Parallel-Plate LoadingD3241 Test Method for Thermal Oxidation Stability ofAviation Turbine FuelsD3567 Practice for Determining Dimensions of “Fiberglass”(Glass-Fiber-Reinforced Thermosetting Resin) Pipe andFitt

9、ingsD3951 Practice for Commercial PackagingD5685 Specification for “Fiberglass” (Glass-Fiber-Reinforced Thermosetting-Resin) Pressure Pipe FittingsF412 Terminology Relating to Plastic Piping SystemsF1173 Specification forThermosetting Resin Fiberglass PipeSystems to Be Used for Marine Applications2.

10、2 Military Specification:MIL-T-5624 Turbine Fuel, Aviation, Grades JP-4, JP-5 andJP-5/JP-8 ST32.3 ANSI Standard:B16.5 Steel Pipe Flanges and Flanged Fittings43. Terminology3.1 DefinitionsDefinitions are in accordance with Termi-nologies D883 and F412, and abbreviations are in accordancewith Terminol

11、ogy D1600, unless otherwise indicated.3.2 Definitions of Terms Specific to This Standard:3.2.1 conductivea pipe or fitting that meets the require-ments for conductivity listed in Section 6 of SpecificationF1173.3.3 Abbreviations:3.3.1 RTRP, nreinforced thermosetting resin pipe.4. Classification4.1 G

12、eneral:1This specification is under the jurisdiction of ASTM Committee D20 onPlastics and is the direct responsibility of Subcommittee D20.23 on ReinforcedPlastic Piping Systems and Chemical Equipment.Current edition approved Sept. 1, 2016. Published September 2016. Originallyapproved in 1995. Last

13、previous edition approved in 2010 as D5677 05 (2010).DOI: 10.1520/D5677-16.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe

14、 ASTM website.3Available from Standardization Documents Order Desk, DODSSP, Bldg. 4,Section D, 700 Robbins Ave., Philadelphia, PA 19111-5098, http:/dodssp.daps.dla.mil.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.*A Su

15、mmary of Changes section appears at the end of this standardCopyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.1.1 Pipe meeting this specification is classified by type,grade, and class similar to Classification D2310.4.1.2 Fittings me

16、eting this specification are also classifiedby type (method of manufacture) and grades (generic type ofresin).4.2 Pipe:4.2.1 Type I Filament-Wound Pipe Nonconductive4.2.2 Type Ia Filament-Wound Pipe Conductive4.2.3 Type II Centrifugally Cast Pipe4.3 Fittings:4.3.1 Type I Filament-Wound Fittings Nonc

17、onductive4.3.2 Type Ia Filament Wound Fittings Conductive4.3.3 Type Il Molded Fittings Nonconductive4.4 Grade:4.4.1 Grade 1 Glass-Fiber-Reinforced Epoxy Resin (Pipeand Fittings)4.5 Classes (Pipe Only):4.5.1 Class A No Liner4.5.2 Class C Epoxy Resin Liner Nonreinforced4.5.3 Class F Epoxy Resin Liner

18、Reinforced5. Materials and Manufacture5.1 GeneralThe fiberglass pipe shall be round andstraight, and the pipe and fittings shall be of uniform density,resin content, and surface finish. All pipe ends shall be cut atright angles to the axis of the pipe and any sharp edgesremoved. The bore of the pipe

19、 and fittings shall have a smooth,uniform surface with no exposed fibers and is permitted tocontain a liner. The liner, if used, shall be composed of anepoxy resin formulation and is permitted to contain a reinforce-ment.5.2 MaterialThe pipe and fittings shall be made fromepoxy resins and glass-fibe

20、r reinforcement of commercial firstquality. Fillers, colorants, and other materials are permitted tobe added, provided the pipe and fittings meet all the require-ments of this specification. Epoxy pipe shall be joined onlywith epoxy fittings.5.3 AdhesiveAdhesive for joint assembly shall be a ma-teri

21、al suitable for providing a seal between the pipe and fittingsin continuous service up to 150F (65C) and 150 psig (1034kPa) with surges to 275 psig (1896 kPa). The adhesive shall besupplied as a kit which includes containers of all componentsin the amounts needed for each adhesive mixture. Instructi

22、onsfor use shall be marked on each container or listed on aninstruction sheet included in each adhesive kit. When specifiedin the contract or purchase order, adhesive kits shall befurnished in a sufficient quantity for the particular procurementof pipe and fittings.6. Dimensions6.1 PipeThe pipe shal

23、l be 1, 1.5, 2, 3, 4, 5, 6, 8, 10, 12, 14,16, 18, 20, 22, and 24-in. (25, 40, 50, 80, 100, 125, 150, 200,250, 300, 350, 400, 450, 500, 550, and 600-mm) nominal sizesas specified and shall have the dimensions and tolerancesshown in Table 1 unless otherwise agreed upon by thepurchaser and seller.6.1.1

24、 LengthUnless other lengths are specified on thepurchase order, the length of the pipe shall be 20 ft (6.1 m), 30ft (9.2 m), or 40 ft (12.2 m) with a plus tolerance of 2 ft (0.6m) and a minus tolerance of 5 ft (1.5 m).6.1.2 Wall ThicknessThe minimum wall thickness of thepipe shall be not less than 8

25、7.5 % of the average wall thicknessof the pipe as measured in Section 8 and tested in Section 9.6.1.3 FittingsFittings shall be 1, 1,5, 2, 3, 4, 6, 8, 10, 12,14, 16, 18, 20, 22, and 24-in. (25, 40, 50, 80, 100, 150, 200,250, 300, 350, 400, 500, 550, and 600-mm) nominal sizes, asspecified, and shall

26、have dimensions suitable for joining to thepipe and enabling the pipe and fitting joint to meet therequirements of this specification. For purposes of thisspecification, fittings shall include couplings and flanges.6.1.4 FlangesFlanges shall conform to the bolt hole sizesand pattern for 150-lb steel

27、 flanges in accordance with ANSIB16.5.TABLE 1 Dimensions of PipeNOTE 1Nominal pipe diameters of 14 in. (350 mm), 16 in. (400 mm), 18 in. (450 mm), 20 in. (500 mm), 22 in. (550 mm), and 24 (600 mm) areavailable and approved with outside diameters or inside diameters as specified in Table 1.Nominal Pi

28、pe Diameter Outside Diameter Tolerance, Type I and Type Ia Tolerance, Type IIin. (mm) in. (mm) in. (mm) in. (mm)1 (25) 1.315 (33.40) +0.060 0.016 (+1.52 0.41) 0.009 (0.229)1.5 (40) 1.900 (48.26) +0.060 0.018 (+1.52 0.46) 0.009 (0.229)2 (50) 2.375 (60.32) +0.060 0.018 (+1.52 0.46) 0.012 (0.30)3 (75)

29、3.500 (88.90) 0.060 0.018 (+1.52 0.46) 0.012 (0.30)4 (100) 4.500 (114.30) 0.060 0.018 (+1.52 0.46) 0.015 (0.38)5 (125) 5.563 (141.30) 0.060 0.028 (+1.68 0.71) 0.025 (0.64)6 (150) 6.625 (168.28) 0.066 0.028 (+1.68 0.71) 0.025 (0.64)8 (200) 8.625 (219.08) 0.086 0.040 (+2.28 1.02) 0.025 (0.64)10 (250)

30、10.750 (273.05) 0.108 0.048 (+2.74 1.22) 0.025 (0.64)12 (300) 12.750 (323.05) 0.128 0.056 (+3.25 1.42) 0.025 (0.64)14 (350) 14.000 (355.60) 0.145 0.064 (+3.68 1.63) 0.035 (0.89)16 (400) 16.000 (406.40) 0.165 0.074 (+4.19 1.88) 0.035 (0.89)18 (450) 18.000 (457.20) 0.250 6.3520 (500) 20.000 (508.00) 0

31、.250 6.3522 (550) 22.000 (558.80) 0.250 6.3524 (600) 24.000 (609.60) 0.250 6.35D5677 1627. Performance Requirements7.1 Joint StrengthPipe, fittings, adhesive, and joints shallshow no porosity or other evidence of failure when tested inaccordance with 9.2.2.7.2 Hydrostatic StrengthPipe, fittings, adh

32、esive, and jointsshall withstand a hydrostatic pressure of 300 psi (2068 kPa)without any indication of porosity, delamination, splitting, orother evidence of failure when tested in accordance with 9.2.3.7.3 Impact ResistancePipe and fittings shall show noporosity or visual evidence of damage that wo

33、uld affectserviceability when tested in accordance with 9.2.4.7.4 Boil ResistancePipe and fittings shall show no evi-dence of delamination or other impairment and shall have aweight gain no greater than 1.0 % when tested in accordancewith 9.2.5.7.5 External Load ResistanceWhen tested as specified in

34、9.2.6, the pipe shall show no visual evidence of cracking,crazing, or other damage that could allow leakage of fuelthrough the pipe wall at 5 % deflection and no visual evidenceof delamination, rupture, or other structural damage at 10 %deflection.7.6 Degradation Resistance:7.6.1 Pipe and FittingsPi

35、pe and fittings exposed to JP-5and JP-5/JP-8 STfuels, or JetAand JetA-1, in accordance with9.2.7, shall exhibit no visual evidence of deterioration as aresult of exposure to the fuels and shall have short-time rupturestrengths of not less than 90 % of the short-time rupturestrengths of unexposed pip

36、e and fittings when tested inaccordance with 9.2.7.1.7.6.2 FuelsJP-5 and JP-5/JP-8 ST, or Jet A and Jet A-1fuels contained within pipe and fittings in accordance with 4.2and 4.3, shall not vary from control samples of the fuels inthermal stability and existent gum properties when tested, asspecified

37、, in accordance with 9.2.7.2.7.6.3 Hydrostatic Proof TestPipe and fittings shall with-stand a hydrostatic pressure of 275 psi (1551 kPa) without anyindication of porosity when tested in accordance with 9.2.8.8. Workmanship8.1 Pipe and FittingsThe pipe and fittings shall be freefrom all defects inclu

38、ding delaminations, cracks, indentations,bubbles, pinholes, porosity, and resin-rich and resin-starvedareas which, due to their nature, degree, or extent, detrimen-tally affect the strength and serviceability of the pipe andfittings. The liner, if used in the pipe or fittings, shall be free ofcracks

39、, chips, or other damage.8.2 Examination:8.2.1 SamplingA sufficient quantity of pipe, fittings, andadhesive kits, in accordance with accepted statistical practiceand as agreed upon between the purchaser and the seller, shallbe selected from each lot or shipment and examined todetermine conformance w

40、ith this specification. In the case ofno prior agreement, random samples selected by the testinglaboratory shall be deemed adequate.8.2.2 Pipe and FittingsSample pipe and fittings selectedshall be examined for the following defects: incorrect dimen-sions; ends of pipe not cut at right angles to the

41、axis; exposedfibers or nonuniform surface on bore of pipe or fittings; crackedor chipped liner (if used); bubbles, pinholes, delaminations,cracks, indentations, resin-rich or resin-starved areas in theouter wall that will affect the strength and performance of theproduct; and incorrect or missing id

42、entification marking. Anysample pipe or fitting having one or more of the defects listedshall be considered a defective unit.8.2.3 DimensionsPipe and fitting dimensions shall bedetermined in accordance with the applicable sections ofPractice D3567.8.2.4 AdhesiveSample adhesive kits selected shall be

43、examined for missing adhesive components and instructionsfor use, and missing or incorrect identification marking. Anysample adhesive kit having one or more of the defects listedshall be considered a defective unit.9. Test Methods9.1 SamplingAll pipe and fittings shall be tested to deter-mine confor

44、mance to the hydrostatic proof test requirements of7.6.3 unless otherwise agreed upon by the purchaser and theseller. The rate of sampling for the destructive tests specified in9.2.2 to 9.2.6 (joint strength, impact resistance, boil resistance,beam strength, and cycling resistance) other tests liste

45、d shall bein accordance with the accepted statistical practice unlessotherwise agreed upon between the purchaser and the seller. Inthe case of no prior agreement, random samples selected by thetesting laboratory shall be deemed adequate.9.2 TestsSample pipe, fittings, and adhesive kits selectedshall

46、 be subjected to the tests in accordance with 9.2 through9.2.8. Any sample failing to pass any of these tests shall beconsidered a defective unit.9.2.1 Test ConditionsUnless otherwise specified in the testmethod, test specimens shall be conditioned for not less than48 h in a room maintained at 60 to

47、 90F (15 to 32C) and testedat the same temperature range. Unless otherwise specified, thetest pressure in the individual test methods shall have atolerance of +10 0 psig (68.9 kPa) and 0 psig (0 kPa).9.2.2 Joint StrengthJoint assemblies containing the pipe,fittings, and adhesive shall be fabricated.

48、 The adhesive shall beapplied and cured as under field conditions in accordance withthe manufacturers printed instructions. The completed testsection shall be either an assembly containing the pipe andeach kind of fitting to be furnished under a contract, or simplyone fitting joined between two piec

49、es of pipe. When a sectioncontaining just one fitting is used, then similar test sectionscontaining the other kinds of fittings to be furnished must alsobe tested. If the test section containing the one fitting is used,the longest end-to-end dimension shall be 18 in. (457 mm) orseven times the outside diameter of the pipe, whichever isgreater, but no longer than 84 in. (2.1 m). If the test sectioncontains more than one fitting, the pipe length between fittingsshall be 6 in. (152

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > ASTM

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1