1、Designation: D 6005 03Standard Test Method forDetermining Slump Resistance of Carpet Adhesives1This standard is issued under the fixed designation D 6005; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A
2、 number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method describes a procedure to measureslump, or sag, resistance of a trowel-grade carpet adhesiveusing a button slump test
3、 apparatus.1.2 This test method provides a visual evaluation to relatetroweled bead profile and trowel pickup.1.3 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are forinformation only.1.4 This standard does not purport to address all of thes
4、afety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 618 Practice for Conditioni
5、ng Plastics for TestingD 907 Terminology of AdhesivesD 2202 Test Method for Slump of Sealants3. Terminology3.1 DefinitionsMany of the terms in this test method aredefined in Terminology D 907.4. Significance and Use4.1 During application, end users typically remove theadhesive from the container usi
6、ng the trowel and spread it ontothe desired substrate. Adhesives with good rheological charac-teristics, therefore, will allow trowel retention. Adhesives withpoor rheological characteristics tend to be unacceptable be-cause they cannot be picked up by a trowel.4.2 Bead configuration is important in
7、 order to provideproper wetting/contact of the carpet backing. Beads drawn witha trowel, which show a nonslumping ridge, are preferredbecause they allow good contact to both substrates.4.3 Measurement of the slump resistance of the adhesivewill allow an end user to know if an adhesive is capable of
8、bothadhering well to the trowel during application and maintain anonflowing adhesive ridge.5. Apparatus5.1 Slump Test Jig, constructed in accordance with TestMethod D 2202.5.2 Gravity Convection Oven, having a temperature con-trolled at 122 6 3.6F (50 6 2C).5.3 Steel Spatula.6. Materials6.1 Adhesive
9、Any appropriate adhesive used to installfloorcovering.6.2 SolventAny appropriate reagent.7. Conditioning7.1 Condition the slump jig and adhesive to be tested 24 hat 73.4 6 3.6F (23 6 2C) and 50 % 6 5 % relative humidityprior to testing.8. Procedure8.1 Place the slump jig on a level table with the fr
10、ont faceupward and the plunger depressed to the limit of its travel.8.2 Apply the adhesive into the cavity of the slump jig. Usea steel spatula to level the adhesive flush with the surface of thetest jig.8.3 Place the jig immediately on its end and advance theplunger to one half of its maximum trave
11、l,316 in. (4.75 mm).8.4 Place the jig immediately in a vertical position on a levelshelf in the oven and condition it 30 min at 122.0 6 3.6F (506 2C) or at a temperature otherwise agreed upon between thesupplier and the tester.8.5 At the end of the 30-min period, take a reading, to thenearest 0.01 i
12、n. (0.2 mm) of the maximum point of flow of theadhesive.8.6 Clean the jig using an appropriate solvent.9. Report9.1 Report the following information:9.1.1 The type of adhesive used.9.1.2 The slump resistance of the adhesive.9.1.3 The test conditions.1This test method is under the jurisdiction of AST
13、M Committee D14 onAdhesives and is the direct responsibility of Subcommittee D14.70 on ConstructionAdhesives.Current edition approved Dec. 1, 2003. Published December 2003. Originallyapproved in 1996. Last previous edition approved in 1996 as D 6005 96.2For referenced ASTM standards, visit the ASTM
14、website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United
15、States.10. Precision and Bias10.1 The precision and bias of this test method for measur-ing the slump resistance of carpet adhesives is essentially asspecified in Test Method D 2202.11. Keywords11.1 adhesive; floorcovering; slump resistanceASTM International takes no position respecting the validity
16、 of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject
17、to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters
18、 Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is
19、 copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D6005032
