1、Designation: D6902 04 (Reapproved 2017)Standard Test Method forLaboratory Measurement of Formaldehyde Evolved Duringthe Curing of Melamine-Formaldehyde-Based Coatings1This standard is issued under the fixed designation D6902; the number immediately following the designation indicates the year oforig
2、inal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method is for the determination of formalde-hyde evol
3、ved from melamine-formaldehyde-based coatingsduring the cure step. The results may be used to determine the“cure formaldehyde” evolved from a sample under controlledlaboratory conditions.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for info
4、rmationonly.1.3 This test method is capable of measuring from 500 g/gto 22 000 g formaldehyde/g dry coating under the testconditions specified (3 000 ml/min total flow, 50 ml/minDNPH tube flow). The ratio of total flow to DNPH tube flowcould be adjusted to extend the range of the method.1.4 This sta
5、ndard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety, health, and environmental practices and deter-mine the applicability of regulatory limitations prior to use.1.5 This in
6、ternational standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT
7、) Committee.2. Referenced Documents2.1 ASTM Standards:2D362 Specification for Industrial Grade Toluene (Withdrawn1989)3D1979 Test Method for Free Formaldehyde Content ofAmino Resins (Withdrawn 2006)3D6191 Test Method for Measurement of Evolved Formalde-hyde from Water Reducible Air-Dry CoatingsE691
8、Practice for Conducting an Interlaboratory Study toDetermine the Precision of a Test Method3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 cure formaldehyde, nthe formaldehyde generated asthe result of a chemical reaction during coating curing.3.1.2 free formaldehyde, nthe res
9、idual formaldehyde in acoating due to the raw materials.4. Summary of Test Method4.1 Approximately 0.2 g of coating formulation is placed inan aluminum foil pan, dried in a vacuum oven at 40C (toremove free formaldehyde and solvents) and then baked at theoptimum process cure temperature for 30 min.
10、Formaldehydeemissions are collected from the cure chamber on a DNPH/Silica tube, which is then extracted and the extract analyzed byHPLC/UV. The amount of formaldehyde evolved from thecoating during the cure step is calculated on both a wet-weightand dry-weight basis. The test is run in triplicate p
11、lus a blankand system standard.5. Significance and Use5.1 This test method measures the amount of formaldehydethat is evolved from a coating containing melamine-formaldehyde resin(s) during cure at elevated temperature.Cure formaldehyde results from a side-reaction during cross-linking of functional
12、ized polymers with melamine-formaldehyde resins. Cure formaldehyde is evolved in the finalbake or cure oven, when the coating temperature is highenough to initiate cross-linking. Formaldehyde can be releasedfrom a coating during application, solvent flash-off and cure.Free formaldehyde is primarily
13、evolved during coating appli-cation and solvent flash-off. Test Method D1979 measures“free formaldehyde” in amino resins and Test Method D6191measures formaldehyde evolved from coatings at ambienttemperature. This method measures only the formaldehydereleased during heat cure, which is primarily “cu
14、re formalde-hyde.”1This test method is under the jurisdiction of ASTM Committee D01 on Paintand Related Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.21 on Chemical Analysis of Paints and Paint Materials.Current edition approved Dec. 1, 2017. Published Dec
15、ember 2017. Originallyapproved in 2003. Last previous edition approved in 2011 as D6902 04 (2011).DOI: 10.1520/D6902-04R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, re
16、fer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed
17、 in accordance with internationally recognized principles on standardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.15.2 This test method is
18、 not intended to duplicate the evolvedformaldehyde from an industrial process, but serves as areproducible comparative laboratory evaluation.5.3 This test method has not been evaluated with catalyzedcoating systems that cure at or below 40C, such as those usedby the wood-finishing industry, and woul
19、d likely requirespecial adaptation for this application.6. Apparatus6.1 High Pressure Liquid Chromatograph (HPLC), either agradient or isocratic system. A gradient system is preferredwhen other aldehydes or ketones are present.NOTE 1The system shall be equipped with a temperature-controlledcolumn ov
20、en. A liquid autosampler is optional.6.2 Column, aC18ODS packed with 5-m pellicular beadswith the dimensions of approximately 4 mm by 75 or 150 mm.A 2-cm guard column packed with the same material isrecommended to protect the analytical column.6.3 Detector, UV/VIS detector capable of measuring absor
21、-bance at 360 nm.6.4 Integrator, peak integration system.6.5 Air Sampling Pump, an air sampling pump with thecapability of maintaining a constant flow rate between 3 and 4L/min. Both an inlet and outlet port must be available formeasuring flow. An SKC AirCheck Sampler Model 224-PCXR8 has been found
22、suitable.6.6 Flow MetersAn in-line mass flow meter or flowsensor capable of measuring 30 to 120 mL/min with at least3 % accuracy. A flow meter or bubble meter capable ofmeasuring 3 to 4 L/min with at least 5 % accuracy.6.7 Glass Purge ChamberA glass purge chamber with amouth at least 60 mm wide and
23、a lid with an air-tight gasketseal. One liter reaction flask, reaction flask head with twothreads, two 5029 tetrafluorethylene polymer bushings andFETFE O-Ring and 124 mm anodized 2 piece clamp, AceGlass part numbers 6511-53, 6513-SP, and 6508-6.6.8 ValvesTwo metering valves to adjust split flow rat
24、e.One valve must be constructed of stainless steel. A Swagelok506-1-316 has been found suitable.6.9 Aluminum Foil Dishes, 58 mm in diameter by 18 mmhigh with a smooth (planar) bottom surface.6.10 Forced Draft Oven, oven, capable of maintaining160C (320F), of adequate size to accommodate one or morep
25、urge chambers.6.11 Vacuum Oven, capable of maintaining 40C and avacuum of 0.1 to 0.2 Barr (100 mm Hg).6.12 Volumetric Glassware, various volumetric flasks andpipettes for preparation of calibration standards. Also, 5-mLvolumetric flasks for sample elution.6.13 Analytical BalanceFour-place analytical
26、 balance ca-pable of measuring to 60.1mg (0.0001 g).6.14 Sherer Impinger Diffuser, A 25 mm dia, 275 mL withimpinger stopper, Ace Glass part number 7538-29 has beenfound suitable.6.15 Water Trap, 1000 mL vacuum flask with stopper.6.16 Thermometer, thermocouple with temperature readoutcalibrated in ra
27、nge of 50F to 400F.7. Reagents and Materials7.1 Purity of ReagentsUse reagent grade chemicals in alltests, unless otherwise specified. Other grades may be used,provided it is first ascertained that the reagent is sufficientlyhigh purity to permit its use without lessening the accuracy ofthe determin
28、ation.7.2 Toluene, technical grade, Specification D362.7.3 Tetrahydrofuran, HPLC Grade.7.4 Water, HPLC Grade.7.5 Acetonitrile, HPLC Grade.7.6 DNPH-Silica Cartridge, Waters Sep-Pak Cartridges,Part # WAT037500.7.7 Formaldehyde/2,4-dinitrophenylhydrazone (DNPH)Complex, may be purchased or prepared in t
29、he laboratory.7.8 Calcium Nitrate Tetrahydrate, reagent grade.7.9 Paraformaldehyde, reagent grade.8. Hazards8.1 Check the suppliers Safety Data Sheet (SDS) on allchemicals before use.9. Preparation of Apparatus9.1 Install the column in the chromatograph following themanufacturers directions and esta
30、blish the operating condi-tions required to give the desired separation (see Table 1).Allow sufficient time for the instrument to reach equilibrium asindicated by a stable baseline.9.2 Purge Chamber Set Up:9.2.1 Assemble apparatus (empty purge chamber, impinger,pump, flow meters and valving) as show
31、n in Fig. 1 with aDNPH cartridge in line (use two DNPH cartridges for water-borne coatings and paraformaldehyde calibration check).9.2.2 Add 500 g of calcium nitrate tetrahydrate to 250 mLofreagent grade water to form a near saturated solution. Place thismixture in the constant humidity Insert the S
32、herer Impinger soTABLE 1 Instrument ConditionsDetector UV/VIS Absorbance 360 nmColumn (Isocratic) C18ODS4by75mmMobile Phase (Isocratic) Water/Acetonitrile/Tetrahydrofuran65/30/5 volume/volumeColumn (Gradient) C18ODS 4 by 150 mmMobile Phase (Gradient) Water/Acetonitrile/TetrahydrofuranA: 65/30/10 vol
33、ume/volumeB: 40/60/0 volume/volume100%Afor1minthenlinear gradientto100%Bin10minFlow Rate 1.5 mL/minColumn Temperature 40CRun Time (Isocratic) 10 minRun Time (Gradient) 15 minInjection Volume 10 to 20 LD6902 04 (2017)2that the solution is 8 in. above the bottom of the impinger tip.Mark the solution l
34、evel on the impinger.NOTE 2This calcium nitrate tetrahydrate solution ensures a constanthumidity of 55 %.Add water when the solution level falls below the mark.9.2.3 Adjust the forced draft oven so that the pan tempera-ture is set at the coating manufacturers recommended optimumprocess cure temperat
35、ure 62F (usually with the range of 260to 310F for automotive coatings). Use a thermocouple tapedto the bottom of the pan to measure pan temperature.9.2.4 Adjust pump flow rate to 3.0 to 3.5 L/min.9.2.5 Adjust valves A and B until the DNPH Cartridge hasa flow of 50 mL/min.9.2.6 Check pump flow rate t
36、o ensure it is still in the properrange. Recommended starting flows; Pump 3.0 L/min, DNPHCartridge 50 mL/min (1:60 split).10. Calibration10.1 Use the information in Table 1 as a guide to select theconditions that give the necessary resolution of formaldehyde-DNPH derivative from interferences in the
37、 samples.10.2 Determination of Relative Response FactorsThe re-sponse factor relative to the standard is determined by means ofthe following procedure. It is good practice to determine therelative retention time daily or with each series of determina-tions.10.2.1 Prepare a minimum four-point standar
38、d curve ofFormaldehyde-DNPH derivative in acetonitrile, ranging from0.1 to 10 g/mL as formaldehyde. Recommended curve 0.1,1.0, 5.0 and 10 g/mL.10.2.2 Inject a 10 to 20 L aliquot of the standard mixtureinto the HPLC. At the end of the chromatographic run,calibrate the integrator by following the manu
39、facturers proce-dure for external standard calibration. If this capability is notavailable, refer to the following calculations. See Figs. 2 and 3for typical chromatograms using the three listed columns.10.2.3 The response factor of each analyte is calculated asfollows:Ranalyte5AanalyteCanalyte(1)wh
40、ere:Ranalyte= response factor for the analyte being calibrated,Canalyte= concentration of formaldehyde in mg/mL, andAanalyte= peak area for the analyte being calibrated.FIG. 1 Page Chamber Set-UpD6902 04 (2017)310.2.4 Calculate the average response factor for all concen-trations and the correlation
41、coefficient for calibration curve. Ifthe correlation coefficient is not 0.9999 or greater, repeatcalibration process.10.3 System Integrity:10.3.1 System BlankFollow procedure (Section 11) belowonly using a blank aluminum foil dish. Result should be belowdetection for formaldehyde.10.3.2 System Stand
42、ardFollow procedure beginning at10.2, using two DNPH cartridges and an oven temperature of150C.Add 4.0 6 0.5 mg of paraformaldehyde to a cool emptypan and record weight to nearest 0.1 mg. Total formaldehydemeasured should be equal to the amount of paraformaldehydeused 65 %, with less than a 1 % brea
43、kthrough to the secondcartridge. Analyze system standard on a minimum daily basis.11. Procedure11.1 Prepare Coating Specimens:11.1.1 Mix the coating sample, preferably on a mechanicalshaker or roller for solventborne and by hand for waterborneFIG. 2 Isocratic Separation of C1-C3Aldehyde and Ketone D
44、erivativesFIG. 3 Gradient Separation of C1-C9Aldehyde and Ketone DerivativesD6902 04 (2017)4coatings, until homogeneous. If air bubbles become entrapped,stir by hand until air has been removed.11.1.2 Rinse aluminum foil dishes (6.9) with toluene, wipedry with a lint-free cloth then bake at cure temp
45、erature andtime. Place dishes in a desiccator to cool after baking.11.1.3 Record the weight of three dry aluminum foil dishes.11.1.4 Measure 0.2 6 0.05 g of coating formulation into atared aluminum foil dish using a syringe by measuring theweight of the syringe before and after dispensing the coatin
46、g.Record weight of the dispensed coating on Bench Data Sheet(Fig. 4).11.1.4.1 For solventborne coatings add 1.5 mL of toluene todisperse the coating evenly on the bottom of the dish.11.1.4.2 For waterborne coatings add one mL of distilledwater, swirling pan until the coating formulation is fullywett
47、ed. Add one mL of ethanol again swirling the pan until thecoating is fully dispersed.11.1.5 Place dish immediately into a level vacuum oven setat 40C.11.1.6 Repeat steps 11.1.3 11.1.5 two more times. Thenevacuate the oven to 0.1 to 0.2 Barr (100 mm Hg).11.1.7 Allow specimens to dry in vacuum oven fo
48、r1hat40C.11.1.8 Remove the dishes from the vacuum oven and placein a covered container at room temperature. Specimens shouldnot stand for more than 72 h between solvent evaporation andcuring.NOTE 3For applications where a clearcoat is applied on top of abasecoat, it is recommended that the procedure
49、 be followed through stepFIG. 4 Bench Data SheetD6902 04 (2017)511.1.8 for the basecoat then return to step 11.1.4 and apply the clearcoat.11.2 Cure Coating Specimens:11.2.1 Assemble apparatus as described in 9.2 with a freshDNPH Cartridge (two cartridges for waterborne coatings).11.2.2 Place one dish containing specimen in a cool (roomtemp) purge chamber.11.2.3 Replace hot empty purge chamber (using insulatedgloves) with chamber containing specimen, attaching the coveras quickly as possible.11.2.4 Record initial flows (Total Flow and Tub
