ASTM D6957-2008 809 Standard Practice for Measuring Curl in Paint Brush Filling Material《测量漆刷子填充材料卷曲度的标准实施规程》.pdf

上传人:explodesoak291 文档编号:524086 上传时间:2018-12-04 格式:PDF 页数:2 大小:54.84KB
下载 相关 举报
ASTM D6957-2008 809 Standard Practice for Measuring Curl in Paint Brush Filling Material《测量漆刷子填充材料卷曲度的标准实施规程》.pdf_第1页
第1页 / 共2页
ASTM D6957-2008 809 Standard Practice for Measuring Curl in Paint Brush Filling Material《测量漆刷子填充材料卷曲度的标准实施规程》.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation: D 6957 08Standard Practice forMeasuring Curl in Paint Brush Filling Material1This standard is issued under the fixed designation D 6957; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A numb

2、er in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice describes the procedure for measuring curlin synthetic filament.1.2 This practice is applicable to filament 2 to 5 in. (50.8

3、to127 mm) in length.1.3 This practice is applicable to tapered filament or levelfilament.1.4 This practice is applicable to loose filling material andmaterial removed from a brush.1.5 The values given in inch-pound units are to be regardedas the standard as this is the dominant measurement systemuse

4、d in the paint brush industry. The values given in parenthe-ses are mathematical conversions to SI units that are providedfor information only and are not considered standard.1.6 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibi

5、lity of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Terminology2.1 Definitions of Terms Specific to This Standard:2.1.1 paint brush filament, na synthetic polymer extrusionused in brushing

6、material.2.1.2 filament curl, ndeviation from straight, along thelength of a filament.2.1.3 butt-end, nthe larger end of a tapered filament;either end of a level filament.3. Significance and Use3.1 It is important for the manufacturing and performance ofa brush to have filaments with minimal curl.4.

7、 Apparatus4.1 Filament curl deviation chart. See Fig. 1.5. Procedure5.1 For Testing Synthetic Filaments:5.1.1 Select filaments to be measured.5.1.2 Allow filaments to acclimate to room temperature 70to 75F (21 to 24C) at least two hours.5.1.3 Place a filament on the filament curl deviation chartwith

8、 butt-end at the x-reference point (see Fig. 1).5.1.4 Record the degree of deviation from straight at theother end of the filament.5.1.5 If multiple filaments of the same type and length are tobe measured, repeat 5.1.3 and 5.1.4 for each of the remainingfilaments and average the results.1This practi

9、ce is under the jurisdiction of ASTM Committee D01 on Paint andRelated Coatings, Materials, and Applications and is the direct responsibility ofSubcommittee D01.61 on Paint Application Tools.Current edition approved Nov. 1, 2008. Published November 2008. Originallyapproved in 2003. Last previous edi

10、tion approved in 2003 as D 6957 - 03.FIG. 1 Filament Curl Deviation Chart1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6. Keywords6.1 curl; filamentASTM International takes no position respecting the validity of any patent rights a

11、sserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time

12、 by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will re

13、ceive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM In

14、ternational, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D6957082

展开阅读全文
相关资源
猜你喜欢
  • API SPEC 6A-2010 Specification for Wellhead and Christmas Tree Equipment (TWENTIETH EDITION Incorporating ERTA 1 January 2011 ADDENDUM 1 November 2011 ERTA 2 November 2011 ADDENDUM.pdf API SPEC 6A-2010 Specification for Wellhead and Christmas Tree Equipment (TWENTIETH EDITION Incorporating ERTA 1 January 2011 ADDENDUM 1 November 2011 ERTA 2 November 2011 ADDENDUM.pdf
  • API SPEC 6DSS-2017 Specification for Subsea Pipeline Valves (THIRD EDITION Effective Date August 1 2018 ERTA 1 May 2018) .pdf API SPEC 6DSS-2017 Specification for Subsea Pipeline Valves (THIRD EDITION Effective Date August 1 2018 ERTA 1 May 2018) .pdf
  • API SPEC 7-1 RUSSIAN-2006 Specification for Rotary Drill Stem Elements (First Edition Effective September 2006 Incorporates Addendum 1 March 2007 Addendum 2 August 2009 Addendum 3 .pdf API SPEC 7-1 RUSSIAN-2006 Specification for Rotary Drill Stem Elements (First Edition Effective September 2006 Incorporates Addendum 1 March 2007 Addendum 2 August 2009 Addendum 3 .pdf
  • API SPEC 7-1 SPANISH-2006 Specification for Rotary Drill Stem Elements (Primera edici n ADENDA 1 marzo 2007 ADENDA 2 Agosto 2009 ISO 10424-1 2004 Adopci n FECHA DE VIGENCIA febrero.pdf API SPEC 7-1 SPANISH-2006 Specification for Rotary Drill Stem Elements (Primera edici n ADENDA 1 marzo 2007 ADENDA 2 Agosto 2009 ISO 10424-1 2004 Adopci n FECHA DE VIGENCIA febrero.pdf
  • API SPEC 7-2 CHINESE-2008 Specification for Threading and Gauging of Rotary Shouldered Thread Connections (First Edition ISO 10424-2 2007 Adoption ADDENDUM 1 DECEMBER 2010 Effectiv.pdf API SPEC 7-2 CHINESE-2008 Specification for Threading and Gauging of Rotary Shouldered Thread Connections (First Edition ISO 10424-2 2007 Adoption ADDENDUM 1 DECEMBER 2010 Effectiv.pdf
  • API SPEC 7-2 RUSSIAN-2017 Threading and Gauging of Rotary Shouldered Connections (SECOND EDITION) .pdf API SPEC 7-2 RUSSIAN-2017 Threading and Gauging of Rotary Shouldered Connections (SECOND EDITION) .pdf
  • API SPEC 7-2 SPANISH-2008 Specification for Threading and Gauging of Rotary Shouldered Thread Connections (Primera edición ISO 10424-2 2007 Adopción FECHA DE VIGENCIA diciembre 01 .pdf API SPEC 7-2 SPANISH-2008 Specification for Threading and Gauging of Rotary Shouldered Thread Connections (Primera edición ISO 10424-2 2007 Adopción FECHA DE VIGENCIA diciembre 01 .pdf
  • API RP 14C-2001 Recommended Practice for Analysis Design Installation and Testing of Basic Surface Safety Systems for Offshore Production Platforms (Seventh Edition)《海上生产平台地面安全系统的分.pdf API RP 14C-2001 Recommended Practice for Analysis Design Installation and Testing of Basic Surface Safety Systems for Offshore Production Platforms (Seventh Edition)《海上生产平台地面安全系统的分.pdf
  • API RP 14F-2008 Design Installation and Maintenance of Electrical Systems for Fixed and Floating Offshore Petroleum Facilities for Unclassified and Class 1 Division 1 and Division .pdf API RP 14F-2008 Design Installation and Maintenance of Electrical Systems for Fixed and Floating Offshore Petroleum Facilities for Unclassified and Class 1 Division 1 and Division .pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > ASTM

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1