ASTM D7326-2006e1 Standard Practice for Handling Transportation and Storage of HFC Blend B (CH2FCF 3 CHF2 CF3 and CO2)《氢氟化碳(HFC)混合B(CHFCF、CHFCF和CO)的搬运、运输和贮藏用标准实施规程》.pdf

上传人:cleanass300 文档编号:525172 上传时间:2018-12-04 格式:PDF 页数:6 大小:142.91KB
下载 相关 举报
ASTM D7326-2006e1 Standard Practice for Handling Transportation and Storage of HFC Blend B (CH2FCF 3 CHF2 CF3 and CO2)《氢氟化碳(HFC)混合B(CHFCF、CHFCF和CO)的搬运、运输和贮藏用标准实施规程》.pdf_第1页
第1页 / 共6页
ASTM D7326-2006e1 Standard Practice for Handling Transportation and Storage of HFC Blend B (CH2FCF 3 CHF2 CF3 and CO2)《氢氟化碳(HFC)混合B(CHFCF、CHFCF和CO)的搬运、运输和贮藏用标准实施规程》.pdf_第2页
第2页 / 共6页
ASTM D7326-2006e1 Standard Practice for Handling Transportation and Storage of HFC Blend B (CH2FCF 3 CHF2 CF3 and CO2)《氢氟化碳(HFC)混合B(CHFCF、CHFCF和CO)的搬运、运输和贮藏用标准实施规程》.pdf_第3页
第3页 / 共6页
ASTM D7326-2006e1 Standard Practice for Handling Transportation and Storage of HFC Blend B (CH2FCF 3 CHF2 CF3 and CO2)《氢氟化碳(HFC)混合B(CHFCF、CHFCF和CO)的搬运、运输和贮藏用标准实施规程》.pdf_第4页
第4页 / 共6页
ASTM D7326-2006e1 Standard Practice for Handling Transportation and Storage of HFC Blend B (CH2FCF 3 CHF2 CF3 and CO2)《氢氟化碳(HFC)混合B(CHFCF、CHFCF和CO)的搬运、运输和贮藏用标准实施规程》.pdf_第5页
第5页 / 共6页
亲,该文档总共6页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation: D 7326 06e1Standard Practice forHandling, Transportation, and Storage of HFC Blend B(CH2FCF3, CHF2CF3, and CO2)1This standard is issued under the fixed designation D 7326; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision

2、, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.e1NOTEReferences to Specification D 7327 were added editorially in May 2007.1. Scope1.1 This practice covers guidan

3、ce and direction to suppliers,reclaimers, purchasers, and users in the handling, transporta-tion, and storage of HFC Blend B.1.2 The values stated in inch-pound and SI units are to beregarded as standard. SI units are preferred.1.3 This standard does not purport to address all of thesafety concerns,

4、 if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D 7327 Specification for HFC Blend B (CH2FCF

5、3, CHF2CF3, and CO2)2.2 CGA Standards:3C-6 Standards for Visual Inspection of Steel CompressedGas CylindersC-7 Guide to Preparation of Precautionary Labeling andMarking of Compressed Gas ContainersP-1 Safe Handling of Compressed Gases in ContainersSB-1 Safety Bulletin: Hazards of Refilling Compresse

6、dRefrigerant (Halogenated Hydrocarbon) Gas CylindersSB-5 Safety Bulletin: Hazards of Reusing Disposable Re-frigerant (Halogenated Hydrocarbon) Gas CylindersSB-18 Safety Bulletin: Use of Refrigerant (HalogenatedHydrocarbons) Recovery Cylinders2.3 U.S. Government Standards:4CFR Title 49, Part 172, Sub

7、part D, U.S. Department ofTransportation (DOT), Marking Requirements of Packag-ing for TransportationCFR Title 49, Part 172.101, U.S. DOT, Tables of HazardousMaterials and Special ProvisionsCFR Title 49, Part 173, U.S. DOT, Shippers-General Re-quirements for Shipping and PackagingsCFR Title 49, Part

8、 178, U.S. DOT, Specifications forPackagingsCFR Title 49, Part 180, U.S. DOT, Continuing Qualificationand Maintenance of Packagings3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 containersstorage vessels for HFC Blend B.3.1.2 cylinderscontainers of HFC Blend B.3.1.3 HFC Blend

9、 Btertiary blend comprised of HFC-134a(1,1,1,2-tetrafluoroethane), HFC-125 (pentafluoroethane), andcarbon dioxide (CO2); a compound used to inert, extinguish, orsuppress a fire or explosion hazard.3.1.4 insulatedplaced in an isolated situation to protectand prevent the transfer of damage.4. Signific

10、ance and Use4.1 This practice provides requirements for the handling,transportation, and storage of HFC Blend B encountered indistribution through both commercial and military channels. Itis intended to ensure that HFC Blend B is handled, transported,and stored in such a way that its physical proper

11、ty virtues are1This practice is under the jurisdiction of ASTM Committee D26 on Haloge-nated Organic Solvents and Fire Extinguishing Agents and is the direct responsi-bility of Subcommittee D26.09 on Fire Extinguishing Agents.Current edition approved Dec. 1, 2006. Published February 2007.2For refere

12、nced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from Compressed Gas Association. Online, .4Available from Sup

13、erintendent of Documents, U.S. Government PrintingOffice, Washington, DC 20036.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.not degraded. Transport may be by various means, such as, butnot limited to, highway, rail, water, and air

14、.5. Practice5.1 To ensure safe handling, loading, unloading, storing,and transporting of material, personnel shall be trained in theCGA publications and Title 49 CFR regulations as listed inSections 2.2 and 2.3, respectively.5.2 Handling:5.2.1 Handling shall be in accordance with CGA P-1, SafeHandli

15、ng of Compressed Gases in Containers.5.2.1.1 Personnel who handle or store, or both, cylinders ofHFC Blend B shall be trained properly to recognize andidentify the characteristics of the product and the propermethods of safely handling full, partially full, and emptycylinders.5.2.2 All HFC Blend B t

16、ransfers between storage containersand recycling processes shall be performed by personneltrained in handling procedures.5.2.2.1 HFC Blend B recycling and transfer processes shallbe in conjunction with the equipment specified by the manu-facturer.5.2.3 HFC Blend B handling shall be in nonsmoking,hea

17、ter-free, ventilated areas to preclude product accumulation.Provisions shall be made to ensure that service areas limit HFCBlend B concentrations do not exceed 75,000 ppm (7.5 %) byvolume for 1 min and 100 ppm by volume for a time weightedexposure of 8 h.5.2.4 Cylinders shall not be overfilled. The

18、liquid portion ofthe HFC Blend B must not completely fill the containersinternal volume at any temperature up to and including 130F(54C). The maximum permitted filling density for HFC BlendB shall be 58 lb/ft3(930 kg/m3). Filling density requirementsare specified in Title 49 CFR, 173.304 and Title 4

19、9 CFR,173.305.5.2.5 Handling of materials should be done in a manner thatprevents contamination or commingling of halocarbons otherthan HFC Blend B.5.2.6 Cylinders shall be free of dirt and contamination thatwould contribute to or would cause deterioration of productduring shipment or storage. Preca

20、utions should be taken toprevent the entry of oil, water, or any other foreign matter intocontainers. Unique coatings or preservatives applied prior toshipment to protect the containers are not considered contami-nation.5.3 Transportation:5.3.1 Transportation shall be as specified in accordance with

21、DOT regulations of Title 49 CFR.5.3.1.1 Shipment of materials between collectors, recyclers,and reclaimers should be within approved DOT guidelines forClass 2, Division 2.2, regulated materials. Any further provi-sions for special transportation or packaging should be agreedupon between the collecto

22、rs, recyclers, and reclaimers.5.3.1.2 The minimum design pressure requirements shall beas indicated in Title 49 CFR, Part 173.304. The pressure insidethe container at 70F (21C) shall not exceed the servicepressure for which the container is marked. The pressure insidethe container at 130F (54C) shal

23、l not exceed54 times theservice pressure for which the container is marked. Fig. 1 andFig. 2 illustrate the effect of temperature on a typical storagecylinder filled with HFC Blend B. Extinguisher filters filledwith HFC Blend B may be under additional nitrogen pressur-ization and isometric diagrams

24、for these conditions are pro-vided in Figs. 3-6.5.3.2 Transportation shall be by suitable vehicles to pre-clude cylinder damage by excessive mechanical vibration,shock, freezing, or deleterious high temperatures throughoutthe entire transport route.FIG. 1 Saturated Vapor Pressure of HFC Blend BEngli

25、sh UnitsD 7326 06e12FIG. 2 Saturated Vapor Pressure of HFC Blend BSI UnitsFIG. 3 Isometric Diagram of HFC Blend B Pressurized with Nitrogen to 360 psig 70FEnglish UnitsD 7326 06e13FIG. 4 Isometric Diagram of HFC Blend B Pressurized with Nitrogen to 600 psig 70FEnglish UnitsFIG. 5 Isometric Diagram o

26、f HFC Blend B Pressurized with Nitrogen to 25 bar 21CSI UnitsD 7326 06e145.3.2.1 If cylinders are expected to be subjected to unac-ceptable transport conditions, the cylinders should be placedunder insulated conditions.5.3.3 Compressed gas cylinder permanent marking require-ments shall be as specifi

27、ed under Title 49 CFR Part 178 andmust be maintained in legible condition as required by Title 49CFR Part 173.5.4 Storage:5.4.1 Storage shall be in accordance with CGA P-1, SafeHandling of Compressed Gases in Containers, in qualifiedcylinders in accordance with Title 49 CFR Parts 173 and 178.5.4.2 C

28、ylinders should be stored in areas that will protectvessels from physical and environmental damage and tamper-ing from unauthorized personnel.5.4.2.1 Facilities should be of construction and orientationso that safety requirements are fulfilled for the storage ofpressurized cylinders.5.4.3 Storage cy

29、linders shall be fitted with pressure releasemechanisms to limit vessel pressure to not more than theminimum required test pressure of the cylinder. Safety reliefvalves should be set not less than 75 %, nor more than 100 %of the minimum required test pressure of the cylinder. Safetyvalves shall be i

30、n contact with the vapor space of the cylinder.5.4.3.1 Periodic hydrostatic testing and reinspection of cyl-inders used for recycled HFC Blend B shall comply with CFRTitle 49, Part 180.5.4.4 Containers shall be clearly marked and labeled toidentify whether the HFC Blend B contained does or does notc

31、onform to Specification D 7327.5.4.5 Insulation shall be placed on pallets or shoring, andprovisions should be made to prevent excessive shock orthermal fluctuations to cylinders.5.4.6 Cylinders shall be stored in a manner that will preventcontamination from external sources.5.4.6.1 If HFC Blend B m

32、eeting the standards of Specifica-tion D 7327 is stored in the same area as material not meetingthe standards, storage shall be segregated or clearly identifiableas not being similar.6. Inspection6.1 HFC Blend B that is reclaimed using HFC Blend Bmanufacturer-approved reclamation systems may be rele

33、asedfor reissue, provided test examination to validate the materialto specification is fulfilled.6.1.1 Reclaimed HFC Blend B that cannot be proven tocomply with Specification D 7327 shall not be reissued. Thematerial will be processed by environmentally safe methodsuntil conformance to the product s

34、tandard is achieved.7. Container, Packaging, and Package Marking7.1 Containers used for shipping and storage of HFC BlendB conforming to this specification shall be marked in accor-dance with Code of Federal Regulations (CFR) Title 49, Part172, Subpart D. The proper shipping name is “CompressedGases

35、. N.O.S., (contains pentafluoroethane, carbon dioxide),2.2, UN1956.” In addition to DOT requirements, containersshould be marked with the following information as a mini-mum:7.1.1 Suppliers name and address, and7.1.2 HFC Blend B.7.1.3 Statement that material conforms to ASTM Specifica-tion D 7327.FI

36、G. 6 Isometric Diagram of HFC Blend B Pressurized with Nitrogen to 42 bar 21CSI UnitsD 7326 06e158. Keywords8.1 1,1,1,2-tetrafluoroethane; CH2FCFl3; CHF2CF3;CO2;HFC-134a; HFC Blend B; carbon dioxide; explosion suppres-sant; fire extinguishant; fire suppressant; handling; pentafluo-roethane; reclamat

37、ion; recovery; recycling; storage; transportASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and

38、 the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revisio

39、n of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you sho

40、uldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).D 7326 06e16

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > ASTM

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1