1、Designation: F1037 10 (Reapproved 2016)1Standard Test Method forVisual Rating of Appearance of Resilient Floors After In-Service Exposure to Foot Traffic1This standard is issued under the fixed designation F1037; the number immediately following the designation indicates the year oforiginal adoption
2、 or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEEditorial changes were made in June 2016.1. Scope1.1 This test method is intended t
3、o provide a numericalrating system for classification of resilient floors during thevarious stages of their wear life in relation to their condition, asperceived by a knowledgeable user.1.2 This standard does not purport to address all of thesafety problems, if any, associated with its use. It is th
4、eresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.1.3 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversi
5、ons to SI units that are provided for information onlyand are not considered standard.2. Referenced Documents2.1 ASTM Standards:2D1436 Test Methods for Application of Emulsion FloorPolishes to Substrates for Testing PurposesF141 Terminology Relating to Resilient Floor Coverings3. Terminology3.1 Defi
6、nitions of Terms Specific to This Standard:3.1.1 surface texturesurface imperfections such as deepscratches, indents, or changes in embossing texture.4. Significance and Use4.1 Ratings are developed by subjective, comparative,evaluation of exposed samples to original unexposed speci-mens of those pa
7、rameters experience has shown to be the mostimportant in the consumers minds in evaluating the perfor-mance of a walking surface. These parameters are a change ingloss, color, surface texture, alterations to pattern and restor-ability of appearance with normal maintenance procedures,including the us
8、e of finishes or buffing. Rating is done by apanel of qualified observers under specified lighting conditionsin accordance with prescribed procedures.5. Apparatus5.1 Buffng Machine, residential, equipped with single ordouble brush (pad), soft fiber polishing brushes, and lambswool pads. When equippe
9、d with polishing brushes, the unitshould deliver a nominal lineal velocity (loaded) of 1100 to1400 ft/min (each brush) and a Dwell ratio of 190 to 210 ft2(17to 19 m2) per min at a pressure of 0.40 to 0.50 psi. Whenequipped with buffing pads, the unit shall deliver a nominallineal velocity (loaded) o
10、f 1100 to 1400 lineal fpm (each pad)and a Dwell ratio of 500 to 550 ft2(45 to 50 m2) per min at apressure of 0.15 to 0.20 psi (see note).5.2 Scrub Brush, approximately 2 by 7 in. (63 by 178mm) with nylon bristles approximately 114 in. (32 mm) long.5.3 Cellulose Sponge, approximate dry dimension8by41
11、4 by 1 in. (203 by 108 mm).6. Reagent6.1 Cleaning Solution, shall be as recommended by theflooring manufacturer and shall be prepared in sufficientquantity in accordance with the manufacturers instructions.NOTE 1For flooring test specimens maintained with polish, thecleaning solution shall be capabl
12、e of removing the polish.7. Sampling, Test Specimens, and Test Units7.1 Specimen size can vary as desired. A typical size panelwould be 24 by 24 in. (610 by 610 mm) and contain four12 by 12 in. (305 by 305 mm) similar or different panels to betested. In addition, a companion specimen must be retaine
13、d andstored in a location where its appearance will not be altered.This specimen will be used for comparison purposes through-out the test cycle. Each sample is to be cleaned in accordancewith the washing procedure in 8.1. The finish procedure shallbe followed on all resilient flooring samples desig
14、ned to be1This test method is under the jurisdiction ofASTM Committee F06 on ResilientFloor Coverings and is the direct responsibility of Subcommittee F06.30 on TestMethods - Performance.Current edition approved Dec. 1, 2010. Published May 2016. Originallyapproved in 1987. Last previous edition appr
15、oved in 2010 as F103710. DOI:10.1520/F1037-10R15E01.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright
16、 ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States1maintained with finish before each rating session. The originalunexposed samples of these products shall be finished also.Those no-finish floors whose appearance, through exposure totraffic, has
17、deteriorated to an overall rating of “3” or more shallbe restored with either the finish procedure (no samples receivedouble-finish) (see 8.2) or the buffing procedure (see 8.3). Thechoice of restorative maintenance is determined by the manu-facturers recommended procedure. All cleaning and restor-a
18、tive maintenance procedures shall be performed on the entiresample.7.2 Before evaluation, each sample shall be prepared usingthe procedure given in Section 8. This procedure is intended toremove all dirt and finish (if present).8. Procedure8.1 Mix the cleaning solution and stir thoroughly.8.1.1 Soak
19、 brush in solution for 1 min.38.1.2 Apply enough solution so that the panel is coveredwith a thin coat of solution. Allow the solution to remainundisturbed for 3 min.8.1.3 Dip brush in solution, then scrub the panel 30 times ineach direction with enough pressure to slightly bend thebristles. Localiz
20、ed, abnormal stains such as chewing gum,ground-out cigarettes, tar, or other spots considered abnormalin residential environment may be given special attention.Overall stains, discoloration, or soil that lodges in deepembossments should not be given special treatment.8.1.4 With the cellulose sponge
21、wrung out in clear, luke-warm water, remove the cleaning solution. Rinse sponge inclear, lukewarm water, wring sponge out lightly, then go overthe panel to rewet the surface. Rinse out sponge again in clearwater. Wring out tightly and remove as much rinse water aspossible.8.1.5 Allow surface to air
22、dry for 1 h.8.2 Finish ProcedureAfter washing, apply to each indi-vidual sample to receive finish, a finish in the followingmanner. Use a fresh supply of an acrylic floor finish or anequivalent material appropriate for the specific type of floor.Apply the finish in accordance with Method B of Test M
23、ethodsD1436.48.3 Buffng ProcedureFollowing the washing procedureoutlined in 8.2, samples of resilient floor coverings whosemanufacturers recommend buffing as the restorative mainte-nance should be treated according to the following buffingprocedure.58.3.1 Buff each sample with the polishing brushes,
24、 using aleft to right to left motion covering the entire sample from topto bottom to top again, using overlapping strokes, in 1 min. Noexcess pressure or weight should be used on the buffer.8.3.2 Repeat 8.3.1, using an overlapping top to bottom totop motion, covering the entire sample fully from lef
25、t to rightto left in 1 min.8.3.3 Repeat the bidirectional buffing technique above, us-ing lambs wool pads on the buffer.8.3.4 Washing Lambs Wool PadsFor purposes of this test,the lambs wool pads will be washed every time the equivalentof 2016 in.2(13 104 cm2) samples are buffed according to thisproc
26、edure.8.3.4.1 Pads are to be washed in a mild detergent6and coldwater (2 heaping teaspoons (10.0 g) per gallon (3.8 L) ofwater), rinsed in cold water and air dried (do not “wring out”pads).9. Observer Panel9.1 The panel of observers shall consist of at least threepeople. One-third of the panel shall
27、 consist of a person(s)technically trained in the composition and use of householdcleaning products, such as a home economist or chemist.One-third of the panel shall consist of a person(s) trained in thetechnical characteristics and testing procedures used on resil-ient flooring, such as an engineer
28、 or chemist. One-third of thepanel shall be a non-technically trained person(s) who regu-larly maintains resilient floors in a home. No panel membershall be color blind. The maintenance person shall not beincluded in the observer panel. Members shall be carefullyinstructed on the scoring procedure a
29、nd shall have had priorexperience of at least a complete rating of one sample beforeestablishing a valid scored rating.9.2 Individual panel observers are provided with separatedata sheets and are to separately rate gloss, color, surfacetexture, pattern change and restorative effects of maintenance.T
30、hey may do their rating simultaneously, but should notdiscuss or compare ratings. If any sample requires restorativemaintenance, all panels are returned to the exposure site onlyafter restorative maintenance is complete and ratings forrestorative maintenance are made. Scoring is in accordancewith 11
31、.1.10. Sample Arrangements and Lighting Conditions10.1 Samples are to be washed, waxed where appropriate(See Section 8 and Fig. 1) and assembled with the viewingtemplate as outlined in this section.10.1.1 Place the flooring panels to be rated horizontally ona freestanding 30 in. (762 mm) high table,
32、 the top of which issmaller than the sample panels. This arrangement will enableobservers to walk around the sample and view it from variousangles and positions.10.1.2 Although it is desirable that the flooring samples orthe panel containing the flooring samples be portable to permitplacement in ide
33、al lighting conditions, it is acknowledged that,in the case of installed flooring, this may not be possible. Inthese instances, efforts must be made to simulate the lightingconditions specified in 10.2 and 10.2.1.3Asponge with scrubbing capabilities may be substituted for the scrub brush andcellulos
34、e sponge.4Suitable cross linked acrylic finish as recommended by resilient flooring forrestorative maintenance of their resilient flooring.5Rug Shampooer/Floor Polisher as recommended by resilient flooringmanufacturer, suitable for restorative buffing of resilient floor surface; speed lessthan 1500
35、r/min.6Mild detergent suitable for cleaning scrubbing brushes/pads and buffing pads.Rinse and let dry afterwards.F1037 10 (2016)1210.1.3 Prepare a template that allows viewing of the mainportion of the sample area, but masks its edges (usually12 in.(13 mm) is sufficient). Immediately adjacent, and a
36、s part of thetemplate, is a second opening of identical dimensions. Thepurpose of the second opening is to serve as a comparisonframe for the original, unexposed sample. See Fig. 2 for asketch of such a template that would be used where four12 by 12 in. (305 by 305 mm) samples are attached to a24 by
37、 24 in. (610 by 610 mm) base.10.2 Principal lighting shall be provided by overhead fluo-rescent lights at 3000K. (warm white). Illumination shall beuniform and not less than 150 ft candles at the sample surface.10.2.1 A secondary source of light shall be established toenable observers to evaluate gl
38、oss. The source may be anuncurtained north facing window, a fluorescent fixture placedfacing the samples, or several incandescent spotlights. Colorvalue is not critical but should not be of extreme departurefrom the primary source. The secondary source should be 5 to10 ft (152 to 305 cm) from the fl
39、oor.11. Rating11.1 Rating is established by totaling the scores for eachsample of gloss, color, surface texture, pattern, and restorativemaintenance by each observer. Total scored is then convertedto a final visual rating in accordance with the conversions asfollows:Total Score Final Visual Rating0
40、1Excellent1 to 4 2Good5 to 8 3Acceptable9 to 11 4Poor12 to 16 5UnacceptableNOTE 2Fractional averages will be rounded to the nearest wholenumber.NOTE 3Scoring for each parameter is to be made as a consideration ofFIG. 1 Suggested Rotation Procedure for Panels Under ExposureF1037 10 (2016)13the differ
41、ence between the exposed sample and the original unexposedsample.11.2 For each sample, the ratings of individual observersare averaged.11.3 The final rating is developed by conversion of totalindividual parameter scores (see 11.1). The following finalratings, from 1 to 5, indicates the general condi
42、tion of theflooring.1 Virtually unchanged from the original (total score of 0).2 Slight change in gloss, coloration, or surface texture, nochange in pattern. The following is still highly acceptable inappearance. Restorative maintenance will return sample tooriginal appearance (total score of 1 to 4
43、).3 Significant changes in gloss, coloration, or surface texture,no change in pattern. Appearance might be objectionable to avery “fussy” housekeeper. Restorative maintenance improvesthe appearance but will not return sample to original appear-ance (total score of 5 to 8).NOTE 4There must be no chan
44、ge in pattern for a sample to receive afinal rating of 3 or less.4 Significant degradation of surface involving change ofgloss, color, surface texture, or alteration of the pattern, or acombination thereof. Many housekeepers would desire re-placement. Restorative maintenance does little to improveap
45、pearance (total score of 9 to 11).5 Major damage such as total loss of gloss, objectionablechange of pattern, surface texture, color or a combinationthereof. Most housekeepers would consider the floor no longerserviceable, worn out, and in need of replacement. Restorativemaintenance does not improve
46、 appearance (total score of 12 to16).11.4 The restorative maintenance scores are shown in Fig. 3.12. Precision and Bias12.1 Round robin testing indicates that even though this is asubjective test method, a satisfactory correlation does existbetween product performance and the ability of the raters t
47、odistinguish among the products.13. Keywords13.1 appearance; gloss; maintenance; resilient floors; visualratingFIG. 2 Template, 24 by 24 in. (610 by 610 mm)F1037 10 (2016)14Gloss, Color, Surface Texture and Pattern Scores0Unchanged from original1Slight change from original2Significant change from or
48、iginal3Objectionable changeScore for Waxing/Buffing0Not needed1Will restore to original appearance2Almost restores original appearance3Does little to restore original appearance4Does nothing to restore original appearanceTotal Score to Final Rating ConversionTotal Score Final Rating011to4 25to8 39to
49、11 412 to 16 5NOTE 1Restorative maintenance is performed in terms of waxing, refinishing or buffing when the maintenance score reaches 3 or more.FIG. 3 Visual Rating Data SheetF1037 10 (2016)15ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standa
