1、Designation: F1068 90 (Reapproved 2018) An American National StandardStandard Specification forDoors, Double, Gastight/Airtight, Individually Dogged, forMarine Use1This standard is issued under the fixed designation F1068; the number immediately following the designation indicates the year oforigina
2、l adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification, to be used in conjunction withSpecification F1
3、073, covers the principal dimensions and themechanical requirements for manufacturing steel and alumi-num individually dogged, airtight/gastight double doors forpersonnel access through bulkheads, complete with frames,intended to maintain the structural and the air and gas tightnessintegrity of the
4、bulkheads.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 The following precautionary caveat pertains only to theTest Methods por
5、tion, Section 6, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish appropriate safety, health, andenvironmental practices and determine the applicability ofregu
6、latory limitations prior to use.1.4 This international standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade O
7、rganization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelA131/A131M Specification for Structural Steel for ShipsB209 Specification for Aluminum and Aluminum-AlloySheet and PlateF1073 Specification for Door Fit
8、tings, for Watertight/Gastight /Airtight, Weathertight, and Non-Tight Doors,for Marine Use2.2 ABS Standard:3Rules for Building and Classing Steel Vessels2.3 Military Standards:4MIL-R-900 Rubber Gasket Material, 45 Durometer Hard-nessMIL-C-81706 Coating, Aluminum and Aluminum AlloysMIL-P-24441 Epoxy-
9、Polyamide PaintDoD-STD-2138 Metal Sprayed Coating System for Corro-sion ProtectionTT-E-490 Enamel, Silicone Alkyd Copolymer, Semi-Gloss,ExteriorZZ-R-765 Rubber, Silicone3. Ordering Information3.1 Ordering for doors under this specification shall includethe following:3.1.1 Material of doors,3.1.2 Nom
10、inal and ASTM designations, fixed lights or nolights,3.1.3 Quantity, and3.1.4 Location of active and inactive panels.3.2 Inspection and acceptance of doors shall be agreed uponbetween the purchaser and the supplier.4. Construction, Shape, and Dimensions4.1 The construction, shape, and clear opening
11、dimensionsshall be as shown in Fig. 1 and Table 1; in addition, they shallconform to the following requirements:4.1.1 Door frames shall be supplied as indicated in Fig. 1.The corner radius inside of door frame shall be 8 in. (203 mm).4.1.2 Dogs shall be located on the door panels unlessotherwise spe
12、cified.4.1.3 The doors shall be fitted with dogs, hinges, hasp andstaple assemblies, grab handles, label plates, and hook assem-blies.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting
13、 and Deck Machinery.Current edition approved April 1, 2018. Published May 2018. Originallyapproved in 1987. Last previous edition approved in 2012 as F1068 90 (2012).DOI: 10.1520/F1068-90R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serv
14、iceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American Bureau of Shipping (ABS), ABS Plaza, 16855Northchase Dr., Houston, TX 77060, http:/www.eagle.org.4Available from DLA Document Services, Building
15、4/D, 700 Robbins Ave.,Philadelphia, PA 19111-5094, http:/quicksearch.dla.mil.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standard
16、ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.14.1.4 The position of the grab handles shall be located at thecenter of the height of each d
17、oor panel.4.1.5 The components shall be attached to the steel doors.Components shall be attached to aluminum doors by eitherwelding or bolting.4.1.6 The material of standard door components shall be asgiven in Table 2.4.1.7 Welding shall be done in accordance with ABS Rulesfor Building and Classing
18、Steel Vessels.5. Workmanship, Finish, and Appearance5.1 All sharp and ragged edges shall be ground flush andremoved for personnel protection.5.1.1 The door panels, upon completion, shall be straightwith a tolerance of 6116 in. (1.6 mm).5.2 Pretreatment and priming of door components shall beas follo
19、ws:5.2.1 Steel door and components, except component No. 3,are to be coated with inorganic zinc rich primer, SSPC Paint 20Type I-C, at 1.5 to 3.0 mils (MDFT), both sides, beforeassembly, following surface preparation in accordance with themanufacturers instructions.5.2.2 Aluminum door and components
20、, except componentNo. 3, are to be pretreated with vinyl wash primer coating,followed with lead free, chromate free, anti-corrosion primeNOTE 11 in. = 25.4 mm.FIG. 1 Typical Double-Door DetailsF1068 90 (2018)2coating. Pretreatment and primer are to be applied beforeassembly, following surface prepar
21、ation in accordance with themanufacturers instructions.6. Test Methods6.1 Design all doors with their respective fittings from theinside (stiffener side) to a test head of 5 psi (34 kPa) and aproof test of 7.5 psi (50 kPa) to ensure no deformation of thepanel.6.2 Before delivery certify the doors fo
22、r gastight/airtightintegrity.7. Product Marking7.1 Each door shall be marked with the purchase ordernumber by attaching a CRES label plate to the door panel usingletters at least12 in. (13 mm) high, designating the ASTMdesignation number, nominal number, thickness of the doorplate, and direction of
23、opening. Other markings may be inpaint.7.2 Label plates shall be screwed or bolted to the door panelon steel and aluminum doors, but in no way adversely affectthe airtightness or gas tightness.8. Packaging and Package Marking8.1 Doors shall be crated or attached to a pallet in a manneracceptable for
24、 shipment by a common carrier. The door anddoor frame assembly shall be shipped as one unit with thegasket protected from knife edges by an inserted partition.9. Keywords9.1 airtight; dogged; doors; double doors; gastight; marine;shipSUPPLEMENTARY REQUIREMENTSThe following supplementary requirements
25、 shall apply only when specified by the contract or order.S1. PaintingS1.1 Pretreatment and priming of door components shall bemetal spray coating in accordance with DoD-STD-2138, TypeII on both sides prior to assembly.S1.2 Aluminum door and components shall be treated witha chemical conversion coat
26、ing MIL-C-81706, second primedwith one coat epoxy polyamide primer (Formula 150 ofMIL-P-24441) alkyd haze-gray (TT-E-490 or equal). Applycoating before assembly, following surface preparation inaccordance with the manufacturers instruction.S2. Internal PressureS2.1 Design and proof test pressures ot
27、her than 5 and 7.5 psi(34 and 52 kPa), respectively, if required, shall be indicated.S2.2 Clear openings other than those specified in Table 1,ifrequired, shall be indicated.TABLE 1 Steel and Aluminum DoorsNOTE 11 in. = 25.4 mm.NOTE 22.2 lb=1kg.NOTE 3Weight does not include fittings.Steel DoorsNomin
28、alNumberClearOpening, in.Size of Door,in.Thickness ofDoor Plate,in.Size of Stiffener, in.Size of Frame,Angle, in.CalculatedWeight, lb4066 40 66 42 6814 2114 14 angle 434 114 3386072 60 72 62 7414 2112 14 angle 434 112 14 5036083 60 83 62 8514 212 112 14 angle 434 112 14 569Aluminum Doors4066 40 66 4
29、2 6814 3338 T bar 434 238 171.26072 60 72 62 7414 3338 T bar 434 238 238.46083 60 83 62 8514 3338 T bar 434 238 265.5TABLE 2 Standard Door MaterialNumber Component Steel Aluminum Alloy1 Door panels Specifications A36/A36M or A131/A131M Specification B2092 Gasket retainer Specifications A36/A36M or A
30、131/A131M Specification B2093 Gasket Neoprene 45 Durometer or equal MIL-R-9004 Stiffeners Specifications A36/A36M or A131/A131M Specification B2095 Door frame Specifications A36/A36M or A131/A131M Specification B209F1068 90 (2018)3S3. Special Heat Resisting GasketsS3.1 Special heat resisting gaskets
31、 in accordance withZZ-R-765, Class 3B, Grade 30 are to be installed.S4. Aluminum DoorsS4.1 Aluminum doors for 5 psi (34 kPa) internal andexternal pressures are to be indicated.S5. Additional Test RequirementsS5.1 Test requirements, when indicated, shall allow 1 out of50 doors to be tested for 1.5 ti
32、mes the test requirementsperformed by the manufacturer.ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent
33、rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either
34、for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hear
35、ing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard
36、may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 90 (2018)4
