1、Designation: F1072 94 (Reapproved 2018) An American National StandardStandard Specification forExpanded-Metal Doors1This standard is issued under the fixed designation F1072; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year
2、 of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers steel expanded-metal doorssuitable for installation in expanded-metal bulkheads, struc-t
3、ural bulkheads, and structural arches.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This international standard was developed i
4、n accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committee.2. Referenced Documents2
5、.1 ASTM Standards:2A36/A36M Specification for Carbon Structural SteelA167 Specification for Stainless and Heat-ResistingChromium-Nickel Steel Plate, Sheet, and Strip (With-drawn 2014)3D3951 Practice for Commercial PackagingF783 Specification for Staple, Handgrab, Handle, and Stir-rup Rung2.2 Other D
6、ocuments:ABS Rules for Building and Classing Steel Vessels4AWS D1.1 Structural Welding Code53. Classification3.1 Expanded-metal doors are furnished in four types (seeDetail “J”) as follows:3.1.1 Type IRight hand (RH).3.1.2 Type IILeft hand (LH).3.1.3 Type IIIRight hand reverse (RHR).3.1.4 Type IVLef
7、t hand reverse (LHR).4. Ordering Information4.1 Orders for doors under this specification shall includethis specification number and type.5. Materials and Manufacture5.1 MaterialsSee Table 1.5.2 Manufacture:5.2.1 Doors shall be furnished with the vertical supportchannels and top angle in place. A te
8、mporary brace shall beincluded at the frame bottom to prevent racking.5.2.2 Welding shall be in accordance with AWS D1.1Structural Welding Code or ABS Rules for Building andClassing Steel Vessels.6. Installation Requirements6.1 Doors shall be fitted with rubber-tipped bumpers and amanually operated
9、catch for holding doors in an open position.These shall be furnished and installed by others.6.2 Provision shall be made for the installation of a rim latchset operated by knobs on both sides. This hardware shall befurnished and installed by others.6.3 Padlocks shall be furnished by others.6.4 Any h
10、oles needed in the frame for installation inexpanded-metal or other types of bulkheads shall be made atinstallation by others.7. Dimensions and Tolerances7.1 Dimensions are as indicated in Figs. 1-8 and Table 1.7.2 Tolerance6116 in. (1.5 mm).8. Workmanship, Finish, and Appearance8.1 Doors and frames
11、 shall be free from all cracks, burrs,sharp edges, and other defects.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved April 1, 2018. Publi
12、shed May 2018. Originallyapproved in 1987. Last previous edition approved in 2012 as F1072 94 (2012).DOI: 10.1520/F1072-94R18.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information,
13、 refer to the standards Document Summary page onthe ASTM website.3The last approved version of this historical standard is referenced onwww.astm.org.4Available from American Bureau of Shipping (ABS), ABS Plaza, 16855Northchase Dr., Houston, TX 77060, http:/www.eagle.org.5Available from American Weld
14、ing Society (AWS), 8669 NW 36 St., #130,Miami, FL 33166-6672, http:/www.aws.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on stand
15、ardization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.18.2 The door manufacturer shall apply a nonhazardouscorrosion-inhibiting primer coating t
16、o all door assemblies.9. Packaging and Package Marking9.1 Each expanded-metal door shall be individually packedfor shipment and storage in accordance with Practice D3951.9.2 In addition to any special marking required by thecontract or purchase order, each expanded-metal door shall bemarked in accor
17、dance with Practice D3951.10. Keywords10.1 expanded-metal doors; expanded-metal bulkheads;metal doors; structural arches; structural bulkheadsTABLE 1 Expanded-Metal Door MaterialsNOTE 11 in. = 25.4 mm.Item Number Description1 Frame TopAngle, 6 312 516 in., Specification A36/A36M.2 Frame SideChannel,
18、 C3 5.0, Specification A36/A36M.3 StapleRound bar, Specification F783.4 Door FrameAngle, 114 114 14 in., Specification A36/A36M.5 BraceFlat bar, 2 14 in., Specification A36/A36M.6 Cross BraceFlat bar, 2 14 in., Specification A36/A36M.7 StopFlat bar, 4 14 in., Specification A36/A36M.8 PadFlat bar, 4
19、14 in., Specification A36/A36M.9 HingeSwaged butt, plain, fixed pin, 3- 212-in. Type 316 stainless steel, Specification A167.10 Expanded Metal13-gage 12-in. flat pattern, Specification A36/A36M.11 Temporary BraceAngle 114 114 14 in., Specification A36/A36M. (See 5.2.1.)F1072 94 (2018)2NOTE 11 in. =
20、25.4 mm.FIG. 1 Right-Hand Door and Frame AssemblyType I (Left Hand, Type II Not Shown)F1072 94 (2018)3NOTE 11 in. = 25.4 mm.FIG. 2 Right-Hand Reverse Door and Frame AssemblyType III (Left Hand, Type IV Not Shown)F1072 94 (2018)4NOTE 11 in. = 25.4 mm.FIG. 3 FrameNOTE 11 in. = 25.4 mm.FIG. 4 DoorF1072
21、 94 (2018)5NOTE 11 in. = 25.4 mm.FIG. 5 PadNOTE 11 in. = 25.4 mm.FIG. 6 StopNOTE 11 in. = 25.4 mm.FIG. 7 Brace and Cross BraceF1072 94 (2018)6ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of thi
22、s standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five yea
23、rs andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical commit
24、tee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 1942
25、8-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 11 in. = 25.4 mm.FIG. 8 Installation DetailsF1072 94 (2018)7
