ASTM F1105-2009 Standard Practice for Preparing Aircraft Cleaning Compounds Liquid-Type Temperature-Sensitive or Solvent-Based for Storage Stability Testing《贮藏稳态性检验用液态、对湿度敏感或溶剂基飞行器.pdf

上传人:diecharacter305 文档编号:534184 上传时间:2018-12-06 格式:PDF 页数:2 大小:51.86KB
下载 相关 举报
ASTM F1105-2009 Standard Practice for Preparing Aircraft Cleaning Compounds Liquid-Type Temperature-Sensitive or Solvent-Based for Storage Stability Testing《贮藏稳态性检验用液态、对湿度敏感或溶剂基飞行器.pdf_第1页
第1页 / 共2页
ASTM F1105-2009 Standard Practice for Preparing Aircraft Cleaning Compounds Liquid-Type Temperature-Sensitive or Solvent-Based for Storage Stability Testing《贮藏稳态性检验用液态、对湿度敏感或溶剂基飞行器.pdf_第2页
第2页 / 共2页
亲,该文档总共2页,全部预览完了,如果喜欢就下载吧!
资源描述

1、Designation: F 1105 09Standard Practice forPreparing Aircraft Cleaning Compounds, Liquid-Type,Temperature-Sensitive, or Solvent-Based, for StorageStability Testing1This standard is issued under the fixed designation F 1105; the number immediately following the designation indicates the year oforigin

2、al adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This practice covers the determination of the stability instorage

3、 of liquid enzyme-based, terpene-based, and solvent-based chemical cleaning compounds used to clean the exteriorsurfaces of aircraft.1.2 The values stated in SI units are to be regarded as thestandard. The values given in parentheses are for informationonly.1.3 This standard does not purport to addr

4、ess all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 U.S. Government Document:Feder

5、al Specification PPP-P-704 Pails, Metal Shipping,Steel 1 through 12 Gallons23. Summary of Practice3.1 Storage stability is determined by evaluation of theeffect of time, temperature, and environmental conditions onthe cleaning compound. Samples used for testing are filledcontainers taken from the ma

6、nufacturers controlled productionformulation, packaged, and delivered to the purchaser fornormal use.3.2 The sample container shall be subjected to the specifiedstorage environment for a period of 12 months. The test shallbe completed prior to 24 months from date of packaging.4. Significance and Use

7、4.1 This practice determines the procedure to be used toensure the long-term storage stability of aircraft cleaning andmaintenance products in order to ensure their ability to meetthe shelf-life requirements called up in specifications or con-tract documents. The subsequent testing requirements ared

8、etailed in the specification or contract.5. Sampling5.1 The sample for storage stability testing shall be takenfrom a controlled production formula, packaged lot, or batchdelivered in a sealed, filled container to the purchaser for use.This sample is normally a 1-gal can conforming to FederalSpecifi

9、cation PPP-P-704. This material shall have previouslybeen tested and passed all other specification requirements forqualification or acceptance. The sample container selected forthe test shall be kept sealed and unopened for the duration ofthe test. The sample container shall be durably and legiblym

10、arked with the following minimum information:Storage Stability Test SampleSupplierFormula numberDate of packagingCold test periodHot test periodBatch/Lot No.Test beganTest ends6. Procedure6.1 Storage EnvironmentPlace the sample container in astorage area where a temperature of 10 to 27C (50 to 80F)

11、ismaintained at least 80 % of the total storage test time. Do notsubject the storage test sample to temperature over 32C (90F)or under 12C (10F) during the entire test. Maintain thesample container in a static condition not subject to vibration,rolling, inversion, or other movement. Movement to then

12、ecessary temperature-controlled area for cold- and hot-temperature testing is accepted, but accomplish such transferwith minimum (or no) disturbance of container contents.6.1.1 Cold-Temperature Storage EnvironmentSubject thesample container to a 15-day time interval at 8 6 2C (17 63F). Conduct this

13、cold test interval during the period 90 to 120days after start of the storage stability test time.1This practice is under the jurisdiction of ASTM Committee F07 on Aerospaceand Aircraft and is the direct responsibility of Subcommittee F07.07 on Qualifica-tion Testing of Aircraft Cleaning Materials.C

14、urrent edition approved May 15, 2009. Published June 2009. Originallyapproved in 1987. Last previous edition approved in 2003 as F 1105 03.2Available from Standardization Documents Order Desk, Bldg. 4 Section D, 700Robbins Ave., Philadelphia, PA 19111-5094 Attn: NPODS.1Copyright ASTM International,

15、100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.6.1.2 Hot-Temperature Storage EnvironmentSubject thesample container to a 15-day time interval at 32 6 2C (90 65F). Conduct this hot test interval after 270 days of elapsedtest time but 60 days before the termination

16、 of the storage test.6.1.3 Completion of TestAfter 12 months storage testtime, carefully remove the sample container (if necessary),without agitation, rolling, or inversion, from the storage areaand place in a room, in a stable location for 48 6 1hatatemperature of 22 to 27C (71 to 80F). At the end

17、of 48 h,remove the top of the container and examine the internalsurface for corrosion or sediment. Disregard discoloration ofthe interior surface of the container. Take samples of theproduct and test in accordance with the relevant specificationor contract requirements.7. Keywords7.1 cold test perio

18、d; hot test period; solvent-based cleaningcompounds; storage stabilityASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of a

19、ny such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are

20、invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not recei

21、ved a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F1105092

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > ASTM

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1