1、Designation: F 1333 91 (Reapproved 2002)An American National StandardStandard Specification forConstruction of Fire and Foam Station Cabinets1This standard is issued under the fixed designation F 1333; the number immediately following the designation indicates the year oforiginal adoption or, in the
2、 case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification provides design and constructioncriteria for double and single fire
3、 and foam station cabinets.See Fig. 1 and Fig. 2. Valves, hose, and fittings are notincluded.1.2 Optional back and legs may be provided.1.3 The values stated in inch-pound units are to be regardedas the standard. The values in parentheses are for informationonly.2. Referenced Documents2.1 ASTM Stand
4、ards:A 36/A 36M Specification for Structural Steel2A 53 Specification for Pipe, Steel, Black and Hot Dipped,Zinc Coated Welded and Seamless3A 167 Specification for Stainless and Heat-Resisting Chro-mium Nickel Steel Plate, Sheet and Strip4A 312/A 312M Specification for Seamless and WeldedAustenitic
5、Stainless Steel Pipe3A 569/A 569M Specification for Steel, Carbon (0.15 Maxi-mum, Percent), Hot-Rolled Sheet and Strip, CommercialQuality4B 209 Specification for Aluminum and Aluminum-AlloySheet and Plate5B 221 Specification for Aluminum and Aluminum-AlloyExtruded Bars, Rods, Wire, Shapes and Tubes5
6、F 593 Specification for Stainless Steel Bolts, Hex CapScrews and Studs6F 594 Specification for Stainless Steel Nuts6F 783 Specification for Staple, Handgrab, Handle, and Stir-rup Rung72.2 American National Standards:8ANSI B18.21.1 Lock WasherANSI B18.22.1 Plain Washer2.3 Other Standards:American Bur
7、eau of Shipping Rules for Building andClassing of Steel Vessels9American Welding Society Publication, AWSD 1.1 Structural Welding Code103. Classification3.1 Type I, Single Cabinet (see Fig. 1 and Figs. 3-9):3.1.1 Grade 1Right-hand door active leaf.3.1.1.1 Class A, Mild SteelSpecification A 36/A 36M.
8、3.1.1.2 Class B, Stainless SteelSpecification A 167.3.1.1.3 Class C, AluminumSpecification B 209.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.11 onMachinery and Piping Systems.Current edition ap
9、proved March 15, 1991. Published November 1991.2Annual Book of ASTM Standards, Vol 01.04.3Annual Book of ASTM Standards, Vol 01.01.4Annual Book of ASTM Standards, Vol 01.03.5Annual Book of ASTM Standards, Vol 02.02.6Annual Book of ASTM Standards, Vol 01.08.7Annual Book of ASTM Standards, Vol 01.07.8
10、Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.9Available from American Bureau of Shipping (ABS), ABS Plaza, 16855Northchase Dr., Houston, TX 77060.10Available from The American Welding Society (AWS), 550 NW LeJeune Rd.,Miami, FL 33126.NOTE
11、11 in. = 25.4 mm.FIG. 1 Fire and Foam CabinetType I1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.2 Grade 2Left-hand door.3.1.2.1 Class A, Mild SteelSpecification A 36/A 36M.3.1.2.2 Class B, Stainless SteelSpecification A 167.3.
12、1.2.3 Class C, AluminumSpecification B 209.3.2 Type II, Double Cabinet (see Fig. 2 and Fig. 8):3.2.1 Grade 1Right-hand doors active leaf.3.2.1.1 Class A, Mild SteelSpecification A 36/A 36M.3.2.1.2 Class B, Stainless SteelSpecification A 167.3.2.1.3 Class C, AluminumSpecification B 209.4. Ordering In
13、formation4.1 Fire and foam cabinets ordered in accordance with thisspecification shall include the following:4.1.1 ASTM title, designation, and year of issue,4.1.2 Quantity (number of cabinets),4.1.3 Type, grade, and class, and4.1.4 Optional features.5. Materials and Manufacture5.1 Materials:5.1.1 S
14、ee Table 1.5.1.2 Class materials.5.1.2.1 All materials for Class A cabinets shall meet therequirements of Specifications A 53 and A 36/A 36M or Speci-fication A 569/A 569M, except as specified in Table 1.5.1.2.2 All materials for Class B cabinets shall meet therequirements of Specifications A 167 an
15、d A 312/A 312M, ex-cept as specified in Table 1.5.1.2.3 All materials for Class C cabinets shall meet therequirements of Specifications B 209 and B 221 except asspecified in Table 1.5.2 Manufacture:5.2.1 Welding shall be in accordance with the AmericanBureau of Shipping Rules for Building and Classi
16、ng of Vesselsor American Welding Society Structural Welding Code AWSD1.1.5.2.2 Punchout shall have a 3-in. (approximately 76-mm)diameter hole with three evenly spaced116-in. (approximately1.5-mm) tabs for both sides of cabinet (see Fig. 3).6. Workmanship, Finish, and Appearance6.1 Fire and foam cabi
17、nets shall be free of weld spatter,burrs, and sharp corners, rough edges, and other defects whichmight be hazardous to personnel and equipment.6.2 Surface Requirements:6.2.1 Class A CabinetsCoat with 1.0-mil dry film thick-ness, inorganic zinc silicate, including options.6.2.2 Class B CabinetsUncoat
18、ed. Optional legs coatedwith 1.0-mil dry film thickness, inorganic zinc silicate.6.2.3 Class C CabinetsUncoated.7. Packaging and Package Marking7.1 Loose fasteners and hardware shall be packaged andsecurely attached inside each cabinet.7.2 ShippingEach cabinet shall bear a weathertight tagshowing th
19、e purchase order number, ASTM standard designa-tion, type, and name of manufacturer.FIG. 2 Fire and Foam CabinetType IITABLE 1 Parts ListItem NumberADescriptionB1 Frame plate, 12 gage2 Hinge pad flatbar, 112 in. by 412 in. by 12 gage3 Hinge undrilled butt, 4 in. long by 2 in. wide, commercialstainle
20、ss steel4 Brace angle,34 by34 by18 in.5 Door plate, 12 gage6 Staple round bar,38-in. dimensions in accordance withSpecification F 7837 Hook round bar,14 in.8 Latch flat bar,316 by 1 in.9 Keeper flat bar,316 by 1 in.10 Rivet button monel or aluminum,14 in.11 Clip wrench/nozzle, plate 12 gage12 Snubbe
21、r rubber, commercial13 Retainer plate, 12 gage14 Saddle pipe 6 NPS Schedule 40, Specification A 5315 Strap hose securing, quick disconnect, commercial16 Clip hook securing, commercial, Specification A 16717 Washer TFE-fluorocarbonOptions18 Back plate,316 in.19 Leg angle, 4 by 3 by38 in., Specificati
22、on A 36/A 36M20 Brace angle, 4 by 3 by38 in., Specification A 36/A 36M21 Bolt hex head,38 16 UNC2A by 114-in. long,stainless steel Type 316, Specification F 59322 Washer flat, stainless steel Type 316 for38-in. diameter bolt,ANSI B18.22.1, Type B23 Nut heavy hex38 16 UNC2B, stainless steel Type316,
23、Specification F 59424 Washer lock, stainless steel Type 316 for38-in. diameterbolt, ANSI B18.21.1, RegularType II Double Cabinet Only25 Back bar flat bar, 112 in. by 30 in. by 12 gageAItems 18 to 24 (inclusive) are optional.B1 in. = 25.4 mm.F 1333 91 (2002)27.3 The cabinets shall be crated or attach
24、ed to a pallet in amanner acceptable for shipment by commercial carrier. Thecabinets shall be crated individually.8. Keywords8.1 fire; foam; foam station cabinet; marine technology;shipsFIG. 3 Section “B-B”FIG. 4 Section “C-C”FIG. 5 Wrench/Nozzle Clip Detail “A”FIG. 6 Latch Assembly, Type II, Grade
25、1 Cabinet Shown, OthersSimilar, Detail “B”F 1333 91 (2002)3FIG. 7 Hook Assembly Detail “C”FIG. 8 Hose Rack Detail “D”F 1333 91 (2002)4ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standa
26、rd are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif
27、 not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, whi
28、ch you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,U
29、nited States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).FIG. 9 Front View of Back Leg and Back Option Detail “E”F 1333 91 (2002)5
