1、Designation: F 1712 06Standard Specification forSteel Chain-Link Fencing Materials Used for High SecurityApplications1This standard is issued under the fixed designation F 1712; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the y
2、ear of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers chain-link fencing materialapplications for high security applications.1.2 The value
3、s stated in inch-pound units are to be regardedas standard. The SI values given in brackets are provided forinformation only.2. Referenced Documents2.1 ASTM Standards:2A 121 Specification for Metallic-Coated Carbon SteelBarbed WireA 392 Specification for Zinc-Coated Steel Chain-LinkFence FabricA 491
4、 Specification for Aluminum-Coated Steel Chain-Link Fence FabricA 824 Specification for Metallic-Coated Steel MarcelledTension Wire for Use With Chain Link FenceF 567 Practice for Installation of Chain-Link FenceF 626 Specification for Fence FittingsF 668 Specification for Polyvinyl Chloride (PVC) a
5、ndOther Organic Polymer-Coated Steel Chain-Link FenceFabricF 900 Specification for Industrial and Commercial SwingGatesF 934 Specification for Colors for Polymer-Coated ChainLink Fence MaterialsF 1043 Specification for Strength and Protective Coatingson Steel Industrial Chain Link Fence FrameworkF 1
6、184 Specification for Industrial and Commercial Hori-zontal Slide GatesF 1345 Specification for Zinc-5 % Aluminum-MischmetalAlloy-Coated Steel Chain-Link Fence FabricF 1379 Terminology Relating to Barbed TapeF 1664 Specification for Poly(Vinyl Chloride) (PVC) andOther Conforming Organic Polymer-Coat
7、ed Steel TensionWire Used with Chain-Link FenceF 1665 Specification for Poly(Vinyl Chloride) (PVC) andOther Conforming Organic Polymer-Coated Steel BarbedWire Used With Chain-Link FenceF 1910 Specification for Long Barbed Tape ObstaclesF 1911 Practice for Installation of Barbed Tape2.2 Other Standar
8、d:UL 325 Door, Drapery, Gate, Louver, and Window Opera-tors and Systems33. Significance and Use3.1 Typical end users of this specification require higherthan normal security.4. Materials and Manufacture4.1 FrameworkShall meet the size and strength require-ments in Specification F 1043 for heavy indu
9、strial fenceframework. Where icing conditions and high wind loads areprevalent or fences are higher than 12 ft 3.7 m, strengthrequirements shall be determined through engineering calcula-tions. Horizontal top, mid or bottom rails if specified shall be1.660-in. 42-mm O.D., or roll-formed section 114
10、by 158 in.32 by 41 mm. Framework may be polymer-coated and colorshall be one of the choices listed in Specification F 934.Framework coatings shall be in accordance with SpecificationF 1043.4.2 FabricMesh larger than 1 in. 25 mm shall be 6gauge, 0.192 in. 4.88 mm or 9 gauge, 0.148 in. 3.76 mm:1-in. m
11、esh shall be 9-gauge coated steel wire conforming toSpecifications A 392, A 491,orF 1345 as selected if metallic-coated, or conforming to Specification F 668 if polymer-coated. Mesh smaller than 1 in. shall be 11 gauge, 0.120 in.3.05 mm conforming to Specifications A 491, F 668,orF 1345 as selected.
12、NOTE 1The various chain link fabric specifications list fabric heightsup to and including 12-ft 3.7-m height. Some fabrics are available up to20 ft 6.1 m. Reference Specification F 567 for fabric installationespecially where two fabric heights are spliced horizontally. Chain linkfabric shall be inst
13、alled on the secure side of the fence.1This specification is under the jurisdiction of ASTM Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.50 on High Security Fencesand Perimeter Barriers.Current edition approved Feb. 15, 2006. Published February 2006. Originallyapproved
14、 in 1996. Last previous edition approved in 2002 as F 1712 - 02.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM websi
15、te.3Available from Underwriters Laboratories (UL) Corporate Progress, 333Pfingsten Rd., Northbrook, IL 60062-2096.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.3 Fittings, shall be galvanized steel conforming to Speci-fication F
16、626.4.3.1 Fittings may be polymer-coated after galvanizing.4.3.2 Tie wires shall be 9-gauge, 0.148 in. 3.76 mm,metallic-coated steel or polymer-coated over 9-gauge, 0.148 in.3.76 mm, galvanized steel core wire in accordance withSpecification F 626. The finish coating shall match the finishcoating of
17、 the fabric.4.4 Barbed Tape ObstaclesBarbed tape, when specified,shall conform for Specification F 1910. Barbed tape shall beinstalled in conformance with Practice F 1911. When specify-ing barbed tape, use descriptions as listed in TerminologyF 1379.4.5 Barbed WireMetallic-coated barbed wire shall c
18、on-form to Specification A 121,1212 gauge, 0.099-in. 2.51-mmdiameter strand wire, 14 gauge, 0.030-in. 2.02-mm barbs.4.5.1 Aluminum-coated, coating Type A, Coating Class 40,Design Number 124314R or 124514R.4.5.2 Zinc-coated (galvanized), Coating Type Z, CoatingClass 3, Design Number 12-4-5-14R.4.5.3
19、5 % Aluminum-mischmetal, Coating Type ZA, Coat-ing Class 60, Design Number 124514R.4.5.4 Polymer-coated barbed wire shall conform to Specifi-cation F 1665.4.6 Tension WireMetallic tension wire shall conform toSpecification A 824.4.6.1 Type I Aluminum-coated.4.6.2 Type II Zinc-coated.4.6.3 Type III Z
20、inc-5 % Aluminum Mischmetal.4.6.4 Polymer-coated tension wire shall conform to Speci-fication F 1664.4.7 If a polymer-coated fence system is selected, the colorselection shall be in accordance with Specification F 934.4.8 GatesThe gates shall be in accordance with Specifi-cation F 900 swing gates or
21、 Specification F 1184 slide gates.All bolts used with gates shall be peened to prevent removal ofnut.4.8.1 Pedestrian gates shall be a galvanized steel material1.900-in. 48-mm outside diameter tubular or 2-in. 51-mmsquare. Typical gate size shall be 4-ft 1.2-m wide by 7-ft2.1-m high complete with tr
22、ansom. Manual or electricsecurity locks shall be installed in swing gate frames using alock box and weatherproof enclosure.4.8.2 Vehicular GatesVehicular gates such as those usedfor sally ports shall be single leaf or double leaf overhead slidegates in accordance with Specification F 1184. Consult s
23、ecuritygate specialists for motor type, controls, locking capabilitiesand related security issues. Electric operators shall complywith UL 325.4.9 AccessoriesIf accessories such as electronic sensors,gate operators, etc., are to be employed, the designer isencouraged to contact various producers of t
24、hese products forproduct information and performance criteria.5. Fabric Attachments5.1 Line PostFabric shall be attached with tie wires orother appropriate fasteners.5.2 RailsFabric shall be attached with tie wires or otherappropriate fasteners.5.3 Terminal Post:5.3.1 Fabric, shall be attached to th
25、e terminal post usingtension bars with tension bands or vertical straps.6. Rails6.1 Top, intermediate, and bottom rails may be specified atthe discretion of the designer.7. Barbed Wire7.1 Barbed wire shall be installed, in accordance withSpecification F 567, with one or more strands, depending onthe
26、 degree of security required, or in conjunction with the useof barbed tape obstacles.7.2 Supporting arms for barbed wire, when supplied, shallmeet the requirements of Specification F 626.8. Tension Wire8.1 Fabric shall be secured to tension wire as directed inSpecification F 567, using steel hog rin
27、gs, in accordance withSpecification F 626.8.2 Tension wire shall be stretched independently from thefabric and not interwoven with the fabric, in accordance withSpecification F 567.9. Keywords9.1 barbed tape obstacles; barbed wire; chain-link fencefabric; chain-link fence framework; high security; w
28、ire coat-ing; wire gaugeASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringe
29、ment of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard o
30、r for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views k
31、nown to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F1712062
