1、Designation: F1821 16Standard Consumer Safety Specification forToddler Beds1This standard is issued under the fixed designation F1821; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parenthes
2、es indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONThis consumer safety specification addresses toddler bed incidents that were identified by theConsumer Product Safety Commission (CPSC).In response to inc
3、ident data supplied by the commission, this consumer safety specification attemptsto minimize: entrapment in bed end structures, entrapment between the guardrail and side rail, andentrapment in the mattress support system. Entrapment of a childs head or neck can result inasphyxiation. It also addres
4、ses corner post extensions, which may catch pacifier cords, ribbons,necklaces, or clothing that a child may be wearing and which may be caught on a projection.This consumer safety specification is written in accordance with the current available state-of-the-art technology and will be updated whenev
5、er substantive information becomes available thatnecessitates additional requirements or justifies a revision to existing requirements.1. Scope1.1 This consumer safety specification covers requirementsfor the design and performance of toddler beds. It also containsrequirements for labeling and instr
6、uctional material.1.2 This consumer safety specification is intended to mini-mize incidents to children resulting from normal use andreasonably foreseeable misuse of toddler beds. It does notaddress incidents resulting from alteration or unreasonablemisuse.1.3 For the purposes of this consumer safet
7、y specification, atoddler bed is a bed that is sized to accept a full-size cribmattress and is intended for use by a child not less than 15months of age and who weighs no more than 50 lb (27.7 kg).1.4 No toddler bed produced after the approval date of thisconsumer safety specification shall indicate
8、 compliance withthis specification, either by label or by other means, unless itconforms to all the requirements contained herein.1.5 This consumer safety specification includes the follow-ing sections:Scope Section 1Referenced Documents Section 2Terminology Section 3Calibration and Standardization
9、Section 4General Requirements Section 5Performance Requirement Section 6Test Methods Section 7Marking and Labeling Section 8Instructional Literature Section 9Keywords Section 101.6 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalco
10、nversions to SI units that are provided for information onlyand are not considered standard.1.7 The following safety hazards caveat pertains only to thetest methods portion, Section 7, of this consumer safetyspecification: This standard does not purport to address all ofthe safety concerns, if any,
11、associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D3359 Test Methods for Measuring Adhesion by Tape Tes
12、tD3574 Test Methods for Flexible Cellular MaterialsSlab,Bonded, and Molded Urethane FoamsF1169 Consumer Safety Specification for Full-Size BabyCribs1This consumer safety specification is under the jurisdiction of ASTM Commit-tee F15 on Consumer Products and is the direct responsibility of Subcommitt
13、eeF15.18 on Cribs, Toddler Beds, Play Yards, Bassinets, Cradles and Changing Tables.Current edition approved Oct. 1, 2016. Published October 2016. Originallyapproved in 1997. Last previous edition approved in 2015 as F1821 15. DOI:10.1520/F1821-16.2For referenced ASTM standards, visit the ASTM websi
14、te, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States
15、12.2 Code of Federal Regulations:316 CFR 1303 Ban of Lead-Containing Paint and CertainConsumer Products Bearing Lead-Containing Paint16 CFR 1500 Hazardous Substances Act Regulations, in-cluding the following sections:16 CFR 1500.48 Technical Requirements for Determining aSharp Point in Toys and Othe
16、r Articles Intended forChildren Under 8 Years of Age16 CFR 1500.49 Technical Requirements for Determining aSharp Metal or Glass Edge in Toys and Other ArticlesIntended for Children Under 8 Years of Age16 CFR 1500 .50 -.53 Test Method for Simulating Use AndAbuse of Toys and Other Articles Intended fo
17、r Use ByChildren16 CFR 1501 Method for Identifying Toys and Other Ar-ticles Intended for Use by Children Under 3 Years of AgeWhich Present Choking, Aspiration or Ingestion HazardsBecause of Small Parts3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 bed, nfor the purpose of thi
18、s specification, a toddlerbed, as described in 3.1.2.3.1.2 bed, toddler, nfor the purpose of this specification,any bed sized to accommodate a full-size crib mattress havingminimum dimensions of 5158 in. (1310 mm) in length and 2714in. (690 mm) in width and is intended to provide free accessand egre
19、ss to a child not less than 15 months of age and whoweighs no more than 50 pounds (27.7 kg).3.1.3 end structure, nan upright structure at the head orfoot of a bed to which the side rails or mattress support system,or both, attach.3.1.4 guardrail, nof a bed, a rail attached to a bedintended to help p
20、revent a sleeping occupant from rolling,sliding, or otherwise falling out of the long side of the bed.3.1.5 manufacturers recommended use position, nanyposition that is presented as a normal, allowable, or acceptableconfiguration for the use of the product by the manufacturer inany descriptive or in
21、structional literature. This specificallyexcludes positions that the manufacturer shows in a likemanner in its literature to be unacceptable, unsafe, or notrecommended.3.1.6 mattress support system, nthose components of abed structure that support the mattress.3.1.7 non-paper label, nany label mater
22、ial (such as plasticor metal) which either will not tear without the aid of tools, ortears, leaving a sharply defined edge.3.1.8 paper labels, nany label which tears without the aidof tools and leaves a fibrous edge.3.1.9 partially bounded openings, nany opening in atoddler bed that is not totally e
23、nclosed by boundaries on allsides so that the perimeter of the opening is discontinuous.3.1.10 permanent marking, na marking or label that,during an attempt to remove it manually without the aid oftools or solvents, cannot be removed or tears upon removal, orsuch action damages the surface to which
24、it is attached.3.1.11 removable guardrail, na guardrail that can beremoved without the use of tools.3.1.12 seam, va means of joining fabric components, suchas sewing, welding, heat sealing, or gluing.3.1.13 side rail, nthe structure connecting the end struc-tures.3.1.14 static load, adja vertically
25、downward force appliedby a calibrated force gage or by dead weights.3.1.15 structural failure, ndamage to a component(s) orassembly resulting in partial separation (greater than 0.040 in.(1.00 mm) over original configuration) or complete separationof the component(s) or assembly.4. Calibration and S
26、tandardization4.1 All testing shall be conducted on a concrete floor thatmay be covered with a18-in. (3-mm) thick vinyl flooring cover,unless test instructs differently.4.2 The product shall be completely assembled, unlessotherwise noted, in accordance with the manufacturers in-structions.4.3 No tes
27、ting shall be conducted within 48 h of manufac-turing.4.4 The product to be tested shall be in a room with ambienttemperature of 73 6 9F (23 6 5C) for at least 1 h prior totesting. Testing shall then be conducted within this temperaturerange.4.5 All testing required by this consumer safety specifica
28、-tion is to be conducted on the same unit.5. General Requirements5.1 The bed shall conform to the regulations specified inSection 2 of this specification before and after testing.5.2 There shall be no hazardous sharp points or edges asdefined by 16 CFR 1500.48 and 16 CFR 1500.49 before andafter test
29、ing to this consumer safety specification.5.3 There shall be no small parts as defined by 16 CFR 1501before testing or liberated as a result of testing to thisspecification.5.4 The paint and surface-coating on the product shallcomply to 16 CFR 1303.5.5 Prior to testing, any exposed wood parts shall
30、be smoothand free from splinters.5.6 Scissoring, Shearing, and PinchingA toddler bed,when in the manufacturers recommended use position, shallbe designed and constructed to prevent injury to the occupantfrom any scissoring, shearing, or pinching when members orcomponents rotate about a common axis o
31、r fastening point,slide, pivot, fold or otherwise move relative to one another.Scissoring, shearing, or pinching that may cause injury shallnot be permissible when the edges of any rigid parts admit a3Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW,
32、Mail Stop: SDE, Washington, DC 20401.F1821 162probe that is greater than 0.210in. (5.33mm) diameter andless than 0.375in. (9.53mm) diameter at any accessible pointthroughout the range of motion of such parts.5.7 Protective ComponentsIf a child can grasp compo-nents between the thumb and forefinger,
33、or teeth, such as caps,sleeves, or plugs used for protection from sharp edges, points,or entrapment of fingers or toes, or if there is at least a0.040in. (1.00mm) gap between the component and itsadjacent parent component, such a component shall not beremoved when tested in accordance with 7.7.5.8 O
34、penings:5.8.1 Finger EntrapmentHoles or slots that extend en-tirely through a wall section of any rigid material less than0.375in. (9.53mm) thick and admit a 0.210in. (5.33mm)diameter rod shall also admit a 0.375in. (9.53mm) diameterrod. Holes or slots that are between 0.210 and 0.375 in. (5.33and 9
35、.53 mm) and have a wall thickness less than 0.375 in.(9.53 mm) but are limited in depth to 0.375 in. (9.53 mm)maximum by another rigid surface shall be permissible (seeFig. 1). The product shall be evaluated in all manufacturersrecommended use positions.5.8.2 Torso EntrapmentThere shall be no openin
36、gs in themattress support system, headboard, footboard, guard rail, orany point where these components are joined together that willpermit complete passage of the wedge block (see Fig. 2). Theproduct shall be evaluated in all manufacturers recommendeduse positions when tested in accordance with 6.3,
37、 6.4,or6.5.5.9 LabelingWarning labels (whether paper or non paper)shall be permanent when tested per 7.8. Warning statementsapplied directly onto a surface of the product by hot stamping,heat transfer, printing, wood burning, etc. shall be permanentwhen tested per 7.8.4. Non-paper labels shall not l
38、iberate smallparts when tested in accordance with 7.8.5.5.10 Corner Post ExtensionsNo corner post assemblyshall extend more than 0.06 in. (1.5 mm) above the upper edgeof an end or side panel, whichever is higher, when measuredFIG. 1 Opening ExampleF1821 163from the lowest point on the upper edge of
39、the end panel within3 in. (76 mm) from the outermost contour of the elbow (seeFig. 3).5.10.1 The limitations in 5.10 do not apply to a corner postassembly that extends at least 57 in. (1448 mm) above theuppermost surface of the mattress support.5.10.2 Corner posts intended to accept removable vertic
40、alextensions made up of two or more segments (such as canopypost extensions) shall not permit the attachment of individualsegments such that the resultant vertical extension would be inviolation of the dimensional requirements of 5.10.6. Performance Requirement6.1 Mattress Support SystemThe mattress
41、 support systemshall not disengage or create a hazardous condition as de-scribed in Section 5 of this consumer safety specification whentested in accordance with 7.2.6.2 Mattress Support System Attachment to End Structures:6.2.1 The mattress support system attachment to the endstructures shall not d
42、isengage or create a hazardous conditionas described in Section 5 of this consumer safety specificationwhen tested in accordance with 7.3.6.2.2 In products that contain both side rails and a separatemattress support system, the tests described in both 7.3.2 and7.3.3 shall apply to both.6.3 Mattress
43、Support System OpeningsThere shall be noopenings in the mattress support system which will permitcomplete passage of the wedge block described in Fig. 2 whentested in accordance with 7.2.5.6.4 GuardrailsFor products with guardrails, there shall beno opening in the guardrail structure below the lowes
44、t surfaceof the uppermost member of the guardrail and above themattress support structure that will permit complete passage ofthe wedge block shown in Fig. 2 when tested in accordancewith 7.4.6.4.1 Guardrail HeightThe upper edge of the guardrailshall be at least 5 in. above the top of the manufactur
45、ersmaximum specified mattress thickness. If no maximum mat-tress thickness is specified, the guardrail height shall be basedon a mattress thickness of 6 in. (152 mm). This measurementis defined and shall be taken from the top of the mattresssupport in its lowest position to the top of the guardrail
46、in themanufacturers recommended use position. Using the previ-ously defined measurement, subtract the manufacturers rec-ommended mattress thickness. The remaining difference(height) must be at least 5 in.6.4.2 Guardrail StrengthWhen tested in accordance with7.9 the guardrail shall not break, detach
47、or create a conditionthat would present any of the hazards described in Section 5.Guardrails that do not have any free ends, that is that they areattached to both the headboard and the footboard, are exemptfrom this test. For guardrails with 2 free ends, perform this testat each free end.6.5 End Str
48、uctures and Side RailsThere shall be noopenings between end structures or side rails and the mattresssupport system or above the mattress support system in the endstructures or side rails that will permit complete passage of thewedge block shown in Fig. 2 when tested in accordance with7.5.6.6 Partia
49、lly Bounded OpeningsAll partially boundedopenings in the uppermost edge of any rigid structure of thebed above the level of the mattress support system shallcomply with the requirements of 7.6.6.7 Spindle/Slat Static Load Strength:6.7.1 Toddler beds that contain wooden or metal spindles/slats shall meet the performance requirements outlined insection 6.7.2 or 6.7.3.6.7.2 Except as provided in 6.7.3, after testing in accordancewith the procedure in 7.10, there shall be no complete breakageof a spindle/slat or complete separatio
