1、Designation: F668 11Standard Specification forPolyvinyl Chloride (PVC), Polyolefin and Other Polymer-Coated Steel Chain Link Fence Fabric1This standard is issued under the fixed designation F668; the number immediately following the designation indicates the year of originaladoption or, in the case
2、of revision, the year of last revision.Anumber in parentheses indicates the year of last reapproval.Asuperscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers polyvinyl chloride and otherconforming organic polymer-coated steel cha
3、in-link fabric,coated before weaving. Polyvinyl chloride, polyolefin, andother organic polymer coating hereinafter will be designated aspolymer coating.1.2 Fabric produced from three classes of wire coatings arecovered as follows:1.2.1 Class I consists of polymer coatings extruded overzinc-coated, a
4、luminum-coated, or zinc-5 % aluminum-mischmetal alloy-coated, or zinc-5 % aluminum-mischmetalalloy-coated steel wire.1.2.2 Class 2a consists of polymer coating extruded andadhered to zinc-coated, aluminum-coated, or zinc-5 %aluminum-mischmetal alloy-coated steel wire.1.2.3 Class 2b consists of polym
5、er coating fused and ad-hered to zinc-coated, aluminum-coated, or zinc-5 %aluminum-mischmetal alloy-coated steel wire.1.3 The values stated in inch-pound units are to be regardedas the standard. The values given in parentheses are providedfor information only.2. Referenced Documents2.1 ASTM Standard
6、s:2A90/A90M Test Method for Weight Mass of Coating onIron and Steel Articles with Zinc or Zinc-Alloy CoatingsA370 Test Methods and Definitions for Mechanical Testingof Steel ProductsA428/A428M Test Method forWeight Mass of Coating onAluminum-Coated Iron or Steel ArticlesD1499 Practice for Filtered O
7、pen-Flame Carbon-Arc Expo-sures of PlasticsF552 Terminology Relating to Chain Link FencingF934 Specification for Colors for Polymer-Coated ChainLink Fence MaterialsG152 Practice for Operating Open Flame Carbon Arc LightApparatus for Exposure of Nonmetallic MaterialsG153 Practice for Operating Enclos
8、ed Carbon Arc LightApparatus for Exposure of Nonmetallic MaterialsG155 Practice for Operating XenonArc LightApparatus forExposure of Non-Metallic Materials2.2 U.S. Federal Standard:Fed. Std. No. 123 Marking for Shipments (Civil Agencies)32.3 U.S. Military Standards:MIL-STD-129 Marking for Shipment a
9、nd Storage33. Terminology3.1 DefinitionsFor definitions of terms such as chain-linkfence fabric, selvage, knuckle, twist, and diamond count, seeTerminology F552.4. Ordering Information4.1 Orders for chain-link fence fabric purchased to thisspecification shall include the following information:4.1.1
10、Quantity.4.1.2 Class of polymer coating to be applied to the metallic-coated core wire.4.1.3 Color of coating (see 16.5.1).4.1.4 Size of mesh (see Table 1 ).4.1.5 Diameter of metallic-coated core wire or minimumbreaking strength, or both (see Tables 1-3).4.1.6 Height of fabric.4.1.7 Type of selvage
11、if nonstandard (see 12.1 and 12.2).4.1.8 Diamond count if nonstandard (see 9.1 and Table 2).4.1.9 Certification, if required.1This specification is under the jurisdiction ofASTM Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.40 on Chain Link Fence andWire Accessories.Cur
12、rent edition approved June 1, 2011. Published June 2011. Originallyapproved in 1981. Last previous edition approved in 2007 as F668 - 07. DOI:10.1520/F0668-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of
13、ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from the procuring activity or as directed by the contracting office orfrom Standardization Documents Order Desk, Bldg. 4 Section D, 700 RobbinsAve.,Philadelphia, PA 19111-5094, Attn: NPODS.1
14、Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.2 Any tests required other than those specifically coveredin this specification must be stipulated by the purchaser in theorder or contract.4.3 All rolls of fabric accepted by the purc
15、haser shall bebilled to him on the basis of the original footage of the rollsbefore sampling, unless changed by contractual agreement.5. Materials5.1 Base MetalThe base metal shall be steel of suchquality and purity that, when drawn to the size of wire specifiedand coated with an organic polymer, th
16、e finished fencing shallbe of uniform quality and have properties and characteristics asprescribed in the specification.5.2 Wire used for the manufacture of fabric shall meet therequirements of this specification and shall be capable of beingwoven into fabric without the polymer coating cracking orp
17、eeling. The polymer coating shall be formulated and producedproperly to conform to the requirements of this specification.6. Manufacture6.1 Class 1 polymer-coated wire shall have the polymercoating extruded onto wire that conforms to the requirementsas shown in Table 3.6.2 Class 2a polymer-coated wi
18、re shall have the polymercoating extruded and adhered to wire that is zinc-coated by thehot-dip method, zinc-coated by the electrolytic process, oraluminum-coated by the hot-dip method.6.3 Class 2b polymer-coated wire shall have the polymercoating fused and adhered to wire that is zinc-coated by the
19、hot-dip method, zinc-coated by the electrolytic process, oraluminum-coated by the hot-dip method. The use of a primerprior to the application of a polymer coating may be recom-mended by the polymer manufacturer.NOTE 1Under current practice, the process for producing a Class 2bPVC coating requires th
20、e use of a primer to attain chemical bonding to thesubstrate. In any event, the polymer manufacturers recommendationshould be followed.6.4 Type of metallic coating on the steel wire substrate shallbe the choice of the producer unless otherwise specified.7. Weave7.1 The wire shall be woven throughout
21、 in the form ofapproximately uniform square mesh, having parallel sides andhorizontal and vertical diagonals of approximately uniformdimensions. The top and bottom of the fabric shall be knuckledor twisted as specified in Section 12.8. Size of Mesh8.1 The size of mesh shall conform to the requiremen
22、ts asshown in Table 1.8.2 The permissible variation from the specified size ofmesh shall be 618 in. (3.2 mm) for all mesh sizes over 1 in. (25mm) and 6116 in. (1.6 mm) for all mesh sizes 1 in. (25 mm)and under.8.3 Size of mesh shall be determined by unrolling a roll offabric on a flat surface and ex
23、erting tension in accordance withthe requirements of 18.2, then measuring the minimum cleardistance between the wires forming the parallel sides of themesh.9. Diamond Count9.1 Typical diamond count for each standard height isshown in Table 2. Other diamond counts are permissible,provided that they a
24、re consistent within a lot. The purchaserhas the option to specify the typical diamond count of 4.1.8.10. Size of Wire10.1 Chain-link fabric shall be fabricated from wire diam-eters as necessary to meet the requirements of Table 1. Thediameter shall be determined as the average of two readingstaken
25、at right angles to each other on the straight portion of theparallel sides of the mesh and measured to the nearest 0.001 in.(0.03 mm).10.2 The permissible variation from the specified diameterof the core wire over 0.105 in. (2.67 mm) shall be 60.005 in.(0.13 mm). The permissible variation for the sp
26、ecified diameteron core wires 0.105 in. (2.67 mm) or less shall be 60.004 in.(0.10 mm).11. Height of Fabric11.1 Chain-link fabric, unless otherwise specified by thepurchaser, shall be furnished in the standard heights shown inTABLE 1 Sizes of Wire and MeshANOTE 1For custom fabric heights, see Sectio
27、n 11.SpecifiedDiameterof CoreWire,in.SizeCoreWireGaugeSizeofMesh,in.Height of Fence Fabric, in.0.192 6 2 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.192 6 134 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.148 9 2 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.148 9 134 36, 42, 48, 60, 72, 84, 96, 108, 120,
28、1440.148B9114 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.148 9 1 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.120 11 218 36, 42, 48, 60, 72,0.120 11 2 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.120 11 134 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.120B11 114 36, 42, 48, 60, 72, 84, 96, 108, 120, 144,0
29、.120 11 1 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.120 1158 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.120 1112 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.120 1138 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.105C1258 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.105C1212 36, 42, 48, 60, 72, 84, 96, 10
30、8, 120, 1440.105C1238 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.080C1458 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.080C1412 36, 42, 48, 60, 72, 84, 96, 108, 120, 1440.080C1438 36, 42, 48, 60, 72, 84, 96, 108, 120, 144ASee Table X1.1 for metric equivalents.BThis mesh size and smaller is recommended
31、 for swimming pools.CThese wire sizes should only be used on58 in.,12 in., and38 in. mesh fabrics.See Fig. 1 for criteria on mesh dimensions.FIG. 1 Mesh Dimensions for58-in.,12-in., and38-in. FabricF668 112Table 1. Custom order fabric is available in heights to andincluding 240 ft. (6.56 m). The hei
32、ght of the fabric shall be theoverall dimension from the ends of twists or knuckles. Permis-sible variations from the specified height shall be 61 in. (25mm) for standard selvage on fabric with mesh sizes 1 in. (25mm) and over and 612 in. (13 mm) for all fabric with meshsizes less than 1 in. (25 mm)
33、.12. Selvage12.1 Fabric with 2-in. (50.8-mm) or 218-in. (54.0-mm)mesh, in heights less than 72 in. (1829 mm), shall be knuckledat both selvages. Fabric 72 in. (1829 mm) high and over shallbe knuckled at one selvage and twisted at the other. These arethe standard selvages. Other selvage combinations
34、will besupplied only if specified by the purchaser.NOTE 2Caution: Twisted selvages for fences under 72 in. (1829 mm)in height are not recommended because of consumer safety consider-ations.12.2 The selvages of fabrics with meshes of less than 2 in.(50.8 mm) shall be knuckled on both edges.13. Breaki
35、ng Strength13.1 Wire constituting the fabric shall meet the minimumbreaking strength shown in Table 3, as determined in accor-dance with Test Methods and Definitions A370.13.2 Specimens to establish conformance to this require-ment shall comprise individual pickets from a section of thefence fabric.
36、 The specimens shall be of sufficient length so asto be firmly gripped in the testing machine after straightening.Polymer coating may be removed from the sample by chemicalor mechanical means before testing. The actual gauge length(distance between jaws) of the specimen shall be limited to theundefo
37、rmed length of wire between the two adjacent bends.14. Weight of Zinc, Aluminum, or Zinc-5 % Aluminum-Mischmetal Alloy Coatings14.1 The weight of zinc or aluminum coating shall conformto Table 4.14.2 The weight of coating shall be determined on anindividual piece of wire removed from the fabric. Thi
38、s speci-men may be any length of wire over 12 in. (305 mm) and shallinclude both bends and straight sections, but shall not includeeither twists or knuckles.14.3 The weight of zinc or zinc-5 % aluminum-mischmetalalloy coating shall be determined by the method contained inTest Method A90/A90M after s
39、tripping the polymer coating asoutlined in Section 15.14.4 The weight of aluminum coating shall be determinedby the method contained in Test Method A428/A428M, afterstripping the polymer coating as outlined in Section 15.TABLE 2 Typical Diamond CountANOTE 1Other diamond counts are permitted (see Sec
40、tion 9 on Diamond Count).NOTE 2 For fabric heights over 144 in., see Section 9.NominalDiameterCore Wire, in.Size ofMesh, in.Height of Fence Fabric, in.36 42 48 60 72 84 96 108 120 1440.192 2 1012 1212 1312 1712 2012 2412 2712 3112 3412 41120.148 2 1012 1212 13 1712 2012 2412 2712 3112 3412 41120.148
41、 134 1112 1312 1512 1912 2312 2712 3112 3512 3912 47120.148 114 17 21 23 29 35 41 46 52 56 700.120 2 1012 1212 1412 1712 2012 24120.120 218 912 1112 1312 1612 19120.120 134 1112 1312 1512 1912 2312 2712 3112 3512 3912 47120.120 114 17 21 23 29 35 41 46 52 56 700.120 20 23273345536167690.120580.12012
42、0.120380.105580.10512 see Fig. 10.105380.080580.080120.08038ASee Table X1.1 for metric equivalents.TABLE 3 Breaking Strength of Core WireSpecified Diameter of Core Wire, in.(mm)Minimum Breaking Strengthlbf (N)0.192 (4.88) 2170 (9650)0.148 (4.76) 1290 (5740)0.120 (3.05) 850 (3780)0.105 (2.67) 650 (28
43、90)0.080 (2.03) 380 (1690)TABLE 4 Weight of Zinc, Aluminum, or Zinc-5 % Aluminum-Mischmetal Alloy CoatingsSpecified Diameter ofCore Wire,in. (mm)Minimum Weight ofZinc or Zinc-5 % Aluminum-Mischmetal Alloy Coating,oz/ft2(g/m2)Minimum Weight ofAluminum Coating,oz/ft2(g/m2)0.192 (4.88) 0.40 (122) 0.20
44、(61)0.148 (3.76) 0.30 (92) 0.20 (61)0.120 (3.05) 0.30 (92) 0.20 (61)0.105 (2.67) 0.30 (92) 0.20 (61)0.080 (2.03) 0.25 (76) 0.20 (61)F668 11315. Thickness of Polymer Coating15.1 The thickness of the polymer coating shall be inaccordance with Table 5.15.2 The thickness of polymer coating shall be dete
45、rminedon an individual piece of wire removed from the fabric. Thisspecimen may be any length of wire over 12 in. (305 mm) andshall include both bends and straight sections, but shall notinclude either twists or knuckles.15.3 For Class 1 and Class 2a material, mechanically stripthe polymer coating fr
46、om the wire and measure the minimumand maximum thickness of the polymer coating with a suitablemicrometer.15.4 For Class 2b material, strip the polymer coating bychemical or mechanical means and determine the diameter ofthe bare wire. Scrape the coating from one side of the wire andmeasure the reduc
47、ed diameter with a micrometer. The thick-ness of coating at this point is the difference between themeasurement thus obtained and the measured diameter of thebare wire. In a similar manner, determine the thickness ofcoating at right angles to the first determination.15.5 When removing polymer coatin
48、g by scraping, takecare not to remove any of the metallic surface.16. Properties of Polymer-Coated Wire16.1 The polymer-coated wire from which the fabric iswoven shall have a demonstrated ability to conform to thefollowing requirements:16.2 Adhesion Tests:16.2.1 Class 2a must conform to the requirem
49、ents of 16.2.2.Class 2b must conform to the requirements of 16.2.3.16.2.2 Three specimens from each lot shall be tested.Measure a distance of34 in. (19 mm) from the end of thespecimen. With a regular hand grip wire stripper, exert maxi-mum hand pull parallel to the axis of the wire. Attempt toremove the measured portion of the vinyl sleeve from the corewire. The lot shall be acceptable if the polymer sleeve is notcapable of being removed from the core wire on all threesamples.16.2.3
