1、Designation: F 822 93 (Reapproved 2004)An American National StandardStandard Specification forChest of Drawers (Chiffonier), Steel, Marine1This standard is issued under the fixed designation F 822; the number immediately following the designation indicates the year oforiginal adoption or, in the cas
2、e of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon (e) indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the construction of marinechests of drawers (chiffoniers) of ste
3、el construction to be usedin staterooms and other spaces.1.2 Values stated in inch-pound units are to be regarded asthe standard. The metric equivalents, given in parentheses, areprovided for information only.2. Referenced Documents2.1 ASTM Standards:2A 366/A 366M Specification for Commercial Steel
4、(CS)Sheet, Carbon, (0.15 Maximum Percent) Cold-Rolled3D 907 Terminology of AdhesivesF 825 Specification for Drawers, Furniture, Marine, SteelF 826 Specification for Tops, Furniture, Marine, Steel2.2 American Institute of Steel Construction Manual:AISC Wire and Sheet Metal Gages Equivalent Thicknessi
5、n Decimals of an Inch, U.S. Standard Gauge for UncoatedHot and Cold Rolled Sheets43. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 chest of drawers (chiffonier)a chest of drawers withfour drawers. All four drawers may be of the same size.4. Ordering Information4.1 Orders for it
6、ems purchased under this specification shallinclude the following information:4.1.1 Quantity.4.1.2 Paint:4.1.2.1 ColorPurchaser shall pick from manufacturerssamples or submit sample chip of color desired.4.1.2.2 Manufacturers standard baked enamel will be fur-nished unless otherwise required and ind
7、icated by the pur-chaser.4.1.3 Options for Tops:4.1.3.1 Unless otherwise specified in the ordering docu-ments, the top supplied by the furniture manufacturer may be,at his option, Type I, II, III, or IV in accordance withSpecification F 826.4.1.3.2 Color or pattern of top covering material shall bes
8、pecified.4.1.4 Options for Drawers:4.1.4.1 Padlock eyes shall be furnished on each drawerwhen specified in ordering documents. This security device isnormally used in crew living spaces.4.1.4.2 Drawer locks shall be furnished when specified inordering documents. Master keying of drawer locks will no
9、t beprovided unless required and defined by the ordering docu-ments. Instead, each drawer lock will be keyed differently. SeeSpecification F 825 for lock description.4.1.4.3 A security panel between the two middle drawers toprovide two secure two-drawer storage areas for two crewmembers is only furn
10、ished when specified in ordering docu-ments. All four drawers in this type chest will be of same size.4.1.5 If the total weight of the chest of drawers is required,it shall be requested by the purchaser.5. Materials and Manufacture5.1 For typical design, see Fig. 1.5.2 Sheet metal shall be in accord
11、ance with SpecificationA 366/A 366M, commercial quality.5.2.1 Minimum sheet metal thicknesses shall be:5.2.1.1 Sides and front rails 18 USSG (0.0478 in. or 1.2mm).5.2.1.2 Back 20 USSG (0.0359 in. or 0.9 mm).5.2.1.3 Base frame 16 USSG (0.0598 in. or 1.5 mm).5.3 Joining of Metal Components:5.3.1 Metal
12、 components shall be joined by welding orgluing with a structural adhesive as defined in TerminologyD 907. The back panel may be riveted to the case providedrivets are not visible after installation.5.3.2 Joining shall be adequate to prevent racking of chestduring handling.1This specification is und
13、er the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Current edition approved Nov. 1, 2004. Published November 2004. Originallyapproved in 1983. Last previous edition approved in 1999 as F 822
14、03 (1999).2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Withdrawn.4Available from the American Institute o
15、f Steel Construction, One E. WackerDr., Suite 3100, Chicago, IL 606012001.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5.3.3 Spotwelds shall be spaced approximately 3 in. (76mm) on centers.5.3.4 Visible spotwelds, higher than the
16、general surface ofthe adjacent metal, shall be ground flush.5.3.5 Visible spotweld depressions shall be spot filled andsanded flush.5.4 Side panels shall be suitably stiffened to prevent buck-ling or oil-canning.5.5 Sound deadening shall be vermin proof and applied toback and inner face of sides of
17、chest. Location and thickness ofapplied sound deadener shall be as required to sound-deadenchest.5.6 Top shall be manufactured in accordance with Specifi-cation F 826.5.7 Drawers shall be manufactured in accordance withSpecification F 825.5.8 A furniture base shall be provided suitable for securingc
18、hest of drawers to deck.6. Performance Requirements6.1 The completed chest of drawers, with the top anddrawers installed, shall satisfy the corresponding performancerequirements outlined in Specifications F 825 and F 826.7. Dimensions7.1 For dimensions, see Table 1.8. Workmanship, Finish, and Qualit
19、y Assurance8.1 All workmanship and material shall be of specifiedquality in keeping with the best commercial marine practice soas to produce each item suitable for its intended use.8.2 All exposed burrs, raw or sharp edges which might beinjurious to personnel shall be removed.8.3 Depressions conside
20、red unacceptable for products enduse shall be spot filled and sanded smooth.NOTE 1For description of Type I, II, III, and IV tops, see Specification F 826.NOTE 2For description of drawers, see Specification F 825.NOTE 3For optional security panel, see 4.1.4.3.NOTE 4If chest of drawers is located in
21、a corner, Dimension “E” next to this adjacent wall shall be 0 in. (0 mm). In all other cases, the minimumvalue for Dimension “E” shall be34 in. (19.05 mm).NOTE 5The minimum value for Dimension “F” shall be 4 in. (102 mm).FIG. 1 Chest of DrawersTABLE 1 Chest of Drawers DimensionsDesignationin. mmDime
22、nsion Tolerance Dimension ToleranceWidth A 36116 914 2Height B 37116 940 2Depth C 21116 533 2Toe D 3116 76 2Space,FrontToe EA4 max116 102 max 2Space,SideBase FB4n|Pmax116 121 max 2HeightAIf chest of drawers is located in a corner, Dimension E next to this adjacent wallshall be 0 in. (0 mm). In all o
23、ther cases, the minimum value for Dimension E shallbe34 in. (19 mm).BThe minimum value for Dimension F shall be 4 in. (102 mm).F 822 93 (2004)28.4 Finish:8.4.1 All steel surfaces, unless corrosion resistant or with acorrosion-resistant plating, shall be painted so as to preventcorrosion.8.4.2 Unless
24、 otherwise required by the ordering documents,all parts normally visible on the completed unit shall have themanufacturers standard baked-on enamel finish.8.4.3 Color is to be specified in the ordering documents.9. Inspection and Certification9.1 Manufacturer shall inspect and certify that the item
25、offurniture complies with the furniture specification and theloading requirements as defined in Section 6.10. Packaging and Package Marking10.1 Each item shall be marked in accordance with thepurchase order.10.2 Packaging shall be provided and shall be acceptable toa common carrier.11. Keywords11.1
26、chest of drawers; chiffoniers; marine chest of drawers;marine furnitureASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of
27、any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are
28、 invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not rece
29、ived a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org).F 822 93 (2004)3
