1、Designation: F880 02 (Reapproved 2008)1Standard Specification forStainless Steel Socket-Set Screws1This standard is issued under the fixed designation F880; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of last revision.
2、 A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1NOTE12.3.1 was editorially corrected in February 2012.1. Scope
3、1.1 This specification covers the requirements for austeniticgrade stainless steel socket-set screws (SSS) sizes 0.060through 0.500 in., in two conditions, AF and CW.1.2 UnitsThe values stated in inch-pound units are to beregarded as standard. No other units of measurement areincluded in this standa
4、rd.NOTE 1A complete metric companion to Specification F880 has beendevelopedF880M; therefore, no metric equivalents are shown in thisspecification.1.3 The following hazards caveat pertains only to TestMethod Section, Section 12 of this specification. This standarddoes not purport to address (all of)
5、 the safety problemsassociated with its use. It is the responsibility of the user of thisstandard to establish appropriate safety and health practicesand determine the applicability of regulatory limitations priorto use.2. Referenced Documents2.1 ASTM Standards:2A262 Practices for Detecting Suscepti
6、bility to IntergranularAttack in Austenitic Stainless SteelsA342/A342M Test Methods for Permeability of FeeblyMagnetic MaterialsA380 Practice for Cleaning, Descaling, and Passivation ofStainless Steel Parts, Equipment, and SystemsA555/A555M Specification for General Requirements forStainless Steel W
7、ire and Wire RodsA751 Test Methods, Practices, and Terminology for Chemi-cal Analysis of Steel ProductsA967 Specification for Chemical Passivation Treatmentsfor Stainless Steel PartsD3951 Practice for Commercial PackagingE18 Test Methods for Rockwell Hardness of Metallic Ma-terialsF593 Specification
8、 for Stainless Steel Bolts, Hex CapScrews, and StudsF788/F788M Specification for Surface Discontinuities ofBolts, Screws, and Studs, Inch and Metric SeriesF1470 Practice for Fastener Sampling for Specified Me-chanical Properties and Performance Inspection2.2 ASME Standard:3B 18.3 Socket Cap, Shoulde
9、r and Set Screws, Inch Series3. Classification3.1 The designation of the alloy group and condition for thetwo materials and conditions of this specification shall beconsistent with the stainless steel designations in SpecificationF593.3.2 The austenitic stainless steel socket set screw shall bedesig
10、nated F880 Group 1 Condition AF (solution annealed) orF880 Group 1 Condition CW (cold worked).4. Ordering Information4.1 Orders for material under this specification shall includethe following information:4.1.1 Quantity (number of screws);4.1.2 Dimensions, including nominal thread designation,thread
11、 pitch, nominal screw length (inches) and point configu-ration. A standard part number may be used for this definition;4.1.3 Name of the screw (SSS);4.1.4 Condition AF/CW;4.1.5 Surface finish, if required. If a finish other thanpassivation is required, it must be specified on the order orproduct sta
12、ndard;4.1.6 ASTM specification and year of issue; and4.1.7 Any special or supplemental requirements.4.2 Example50 000 pieces 0.250-20 3 0.375 cone pointSSS CW ASTM F880 XX.1This specification is under the jurisdiction of ASTM Committee F16 onFasteners and is the direct responsibility of Subcommittee
13、 F16.04 on NonferrousFasteners.Current edition approved May 1, 2008. Published August 2008. Originallyapproved in 1986. Last previous edition approved in 2002 as F880 - 02. DOI:10.1520/F0880-02R08.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service a
14、t serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.1Copyright ASTM International, 100 Ba
15、rr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.5. Materials and Manufacture5.1 The screw may be forged, formed, extruded, machined,or ground to meet the dimensional characteristics and perfor-mance requirements.5.2 Heat TreatmentAustenitic alloys Group 1 ConditionAF sc
16、rew shall be annealed by heating to 1900 6 50F toobtain maximum corrosion resistance and minimum perme-ability. The screws shall be held for a sufficient time attemperature, then cooled at a rate sufficient to prevent precipi-tation of the carbide and provide the properties in accordancewith Table 1
17、.5.3 When condition CW is specified, the austenitic alloysshall be annealed as specified in 5.2, generally by the rawmaterial manufacturer, and then cold worked to developspecific properties.6. Chemical Composition6.1 The analysis of the screw material shall conform to thechemical composition specif
18、ied in Table 2.6.2 Unless otherwise specified in the inquiry and purchaseorder (see Supplementary Requirement S2), the choice of alloyused shall be that of the fastener manufacturer as determinedby his fabrication methods and material availability. Thespecific alloy used by the manufacturer shall be
19、 clearlyidentified on all certification required in the purchase order andshall have a chemical composition conforming to the limitsspecified in Table 2.6.3 When chemical analysis is performed by the purchaserusing finished fasteners representing each lot, the chemicalcontents obtained shall conform
20、 to the limits specified in Table2 for the specific alloy. Chemical composition shall conform tothe tolerances specified in Specification A555/A555M.6.3.1 In the event of a discrepancy, a referee analysis of thesamples for each lot as specified in 12.1 shall be made inaccordance with 11.3.1.7. Mecha
21、nical Properties7.1 Socket-set screws, when subjected to a torque test inaccordance with 12.3.1, shall withstand application of the testtightening torque specified in Table 1 without evidence of thesocket reaming or the screw bursting.7.2 The hardness limits from 70 to 95 HRB (125 to 210DPH) for Con
22、dition AF and 96 HRB to 33 HRC (216 to 327DPH) for Condition CW shall be met as determined using TestMethods E18.8. Corrosion Resistance Requirements8.1 Carbide Precipitation:8.1.1 Rod, bar, and wire in the austenitic alloy groups 1, 2,and 3, except the free-machining grades, 303 and 303Se, usedto m
23、ake fasteners in accordance with this specification shall becapable of passing the test for susceptibility to intergranularcorrosion as specified in Practice E of Practices A262.8.1.2 As stated in PracticesA262, samples may be subjectedto the faster and more severe screening test in accordance withP
24、ractice A. Failing Practice A, specimens shall be tested toPractice E and be considered satisfactory if passing Practice E.9. Dimensions9.1 Unless otherwise specified, the product shall conform tothe requirements of ASME B 18.3.10. Workmanship, Finish, and Appearance10.1 Surface TreatmentUnless othe
25、rwise specified,screws shall be cleaned, descaled, and passivated in accordancewith Practice A380 or Specification A967 at the option of themanufacturer.10.2 Surface Discontinuities:10.2.1 The surface discontinuities for these products shallconform to Specification F788/F788M and the additionallimit
26、ations specified herein.10.2.1.1 Processing cracks that connect the socket to theperiphery of the screw are not permissible. Defects originatingon the periphery with a traverse indicating a potential tointersect are not permissible. For peripheral discontinuities, themaximum depth may be 0.06 D.11.
27、Number of Tests11.1 The requirements of this specification shall be met incontinuous mass production for stock and the manufacturershall make sample inspections to ensure that the productconforms to the specified requirements. Additional tests ofTABLE 1 Torsional Strength RequirementsNominal Screw S
28、ize Shortest Nominal Screw Lengths Subject to Torque Testing Test Torque, in.-lb, minCup and Flat Points,mmCone and Oval Points Half Dog Points, mm AF CW0 0.060 0.109 0.125 0.109 0.3 0.61 0.073 0.125 0.141 0.125 0.7 1.22 0.086 0.125 0.141 0.141 0.7 1.23 0.099 0.141 0.156 0.156 1.6 3.34 0.112 0.141 0
29、.172 0.156 1.6 3.35 0.125 0.188 0.188 0.172 3 56 0.138 0.172 0.203 0.188 3 58 0.164 0.188 0.219 0.203 9 1610 0.190 0.188 0.250 0.234 16 2614 0.250 0.250 0.312 0.297 40 67516 0.312 0.312 0.391 0.359 79 13538 0.375 0.375 0.438 0.438 138 237716 0.437 0.438 0.547 0.484 220 37812 0.500 0.500 0.609 0.547
30、358 600F880 02 (2008)12individual shipments of fasteners are not ordinarily necessary.A record of the individual heat of steel in each lot shall bemaintained. The containers shall be coded to permit identifi-cation of the lot.11.2 When specified in the purchase order, the manufacturershall furnish a
31、 test report of the last complete set of chemicalanalysis and mechanical tests for each stock size in eachshipment.11.3 When tests of individual shipments are required,Supplementary Requirement S1 must be specified in theinquiry and order.11.3.1 When the purchaser does not specify the samplingplan a
32、nd basis of acceptance, the following shall apply.11.3.1.1 The lot, for purposes of selecting samples, shallconsist of all products offered for inspection and testing at onetime, that are of the same style, nominal diameter, thread pitch,nominal length, material type, and condition, and surfacefinis
33、h.11.3.1.2 From each lot, samples shall be selected at randomand tested for each requirement in accordance with thefollowing:Number of Pieces in LotNumber ofSamples800 and less 1Over 800 to 8000, incl 2Over 8000 to 22 000, incl 3Over 22 000 511.3.1.3 Should any sample fail to meet the requirements o
34、fa specified test, double the number of samples from the samelot shall be retested for the requirement(s) in which it failed.All of the additional samples shall conform to the specificationor the lot shall be rejected.11.3.1.4 If the failure of a test specimen is due to improperpreparation of the sp
35、ecimen or an incorrect testing technique,the specimen shall be discarded and another test specimensubmitted.11.4 Corrosion Resistance Tests:11.4.1 Unless otherwise specified, inspection for corrosionresistance shall be in accordance with the manufacturersstandard quality control practices. No specif
36、ic method ofinspection is required but the screws shall be produced fromsuitable raw material and manufactured by properly controlledpractices to maintain resistance to corrosion. When corrosiontests are required, Supplementary Requirement S4 must bespecified in the inquiry and order except as noted
37、 in 11.4.2.11.4.2 Products that have been hot worked shall be solutionannealed and tested to determine freedom from precipitatedcarbides. Not less than one corrosion test shall be made fromeach lot. Corrosion tests shall be performed in accordance withPractices A262, Practices A or E as applicable.1
38、2. Test Methods12.1 Chemical AnalysisThe chemical composition shallbe determined in accordance with Test Methods, Practices, andTerminology A751.12.2 The fastener manufacturer may accept the chemicalanalysis of each heat of raw material purchased and reported onthe raw material certification furnish
39、ed by the raw materialproducer. The fastener manufacturer is not required to do anyfurther chemical analysis testing, provided that precise heat lottraceability has been maintained throughout the manufacturingprocess on each lot of fasteners produced and delivered.12.3 Mechanical Tests:12.3.1 For so
40、cket strength torque test, the test screw shall beassembled into a tapped hole of 5H tolerance class in a steelblock (Fig. 1) until the face of the screw is flush with the topsurface of the test block and the set screw bears against a firmTABLE 2 Chemical RequirementsUNSDesignationAlloyComposition,
41、% maximum except as shownCarbon Manganese Phosphorus Sulfur Silicon Chromium Nickel Copper MolybdenumAustenitic AlloysS30300 303 0.15 2.00 0.20 0.15 min 1.00 17.0 to 19.0 8.0 to 10.0 0.60 maxAS30323 303Se 0.15 2.00 0.20 0.060 1.00 17.0 to 19.0 8.0 to 10.0 Se 0.15 minS30400 304 0.08 2.00 0.045 0.030
42、1.00 18.0 to 20.0 8.0 to 10.5 1.00 . . .S30403 304L 0.030 2.00 0.045 0.030 1.00 18.0 to 20.0 8.0 to 12.0 1.00 . . .S30500 305 0.12 2.00 0.045 0.030 1.00 17.0 to 19.0 10.5 to 13.0 1.00 . . .S38400 384 0.08 2.00 0.045 0.030 1.00 15.0 to 17.0 17.0 to 19.0 . . .S20300 XM1 0.08 5.0 to 6.5 0.040 0.18 to 0
43、.35 1.00 16.0 to 18.0 5.0 to 6.5 1.75 to 2.25 0.50 maxAS30430 189LW 0.10 2.00 0.045 0.030 1.00 17.0 to 19.0 8.0 to 10.0 3.0 to 4.0 . . .S30433 302HQ 0.03 2.00 0.045 0.030 1.00 17.0 to 19.0 8.0 to 10.0 3.0 to 4.0 . . .AAt the manufacturers option, determined only when intentionally added.FIG. 1 Typic
44、al Torque Test FixtureF880 02 (2008)13base, such as a hardened screw installed from the opposite sideof the block. The applicable hexagon key bit, in accordancewith ASME B 18.3, shall be inserted to the full depth of the setscrew socket and the test torque listed in Table 1 applied bymeans of a torq
45、ue wrench. The screw shall be disassembledfrom the block and examined for compliance to the require-ments of 6.1.12.4 Corrosion ResistanceWhen specified on the pur-chase order or inquiry, corrosion tests to determine freedomfrom precipitated carbides shall be performed in accordancewith Practices A2
46、62, Practice A or E as applicable.13. Inspection13.1 If the inspection described in 13.2 is required by thepurchaser, it shall be specified in the inquiry, order, or contract.13.2 The inspector representing the purchaser shall havefree entry to all parts of the manufacturers works that concernthe ma
47、nufacture of the material ordered. The manufacturershall afford the inspector all reasonable facilities to satisfy thatthe material is being furnished in accordance with this speci-fication. All tests and inspection required by the specificationthat are requested by the purchasers representative and
48、 pur-chase order shall be made prior to shipment and shall be soconducted as not to interfere unnecessarily with the operationof the work.14. Rejection and Rehearing14.1 Screws that fail to conform to the requirements of thisspecification may be rejected by the purchaser. Rejection shallbe reported
49、to the supplier promptly and in writing. In case ofdissatisfaction with the results of tests or inspection authorizedby the purchaser, the supplier may make claim for a rehearing.15. Certification15.1 Test Report The manufacturer shall maintain on filefor a period of 5 years, the original test report, including a copyof the certified chemical analysis of the heat of material usedand the results of the required testing for the lot of fasteners.15.2 Manufacturers Certificate of ConformanceThemanufacturer shall maintain on file for a period of 5 years, ace
