1、Designation: F900 11 (Reapproved 2017)Standard Specification forIndustrial and Commercial Steel Swing Gates1This standard is issued under the fixed designation F900; the number immediately following the designation indicates the year of originaladoption or, in the case of revision, the year of last
2、revision. A number in parentheses indicates the year of last reapproval. A superscriptepsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers detailed requirements for chainlink fence gates, gate posts and accessories for both single anddo
3、uble swing-type gates for industrial and commercial appli-cation.1.2 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.3 This internation
4、al standard was developed in accor-dance with internationally recognized principles on standard-ization established in the Decision on Principles for theDevelopment of International Standards, Guides and Recom-mendations issued by the World Trade Organization TechnicalBarriers to Trade (TBT) Committ
5、ee.2. Referenced Documents2.1 ASTM Standards:2A780 Practice for Repair of Damaged and Uncoated Areasof Hot-Dip Galvanized CoatingsF1043 Specification for Strength and Protective Coatings onSteel Industrial Fence FrameworkF1083 Specification for Pipe, Steel, Hot-Dipped Zinc-Coated (Galvanized) Welded
6、, for Fence StructuresF2200 Specification for Automated Vehicular Gate Con-struction3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 polymerin this specification, polymer is used todescribe all types of vinyl, poly(vinyl-chloride) (PVC) orsimilar types of coatings other than zi
7、nc or aluminum.4. Materials and Manufacture4.1 MaterialsThe base materials of the gate frame shall beround or rectangular tubular members, welded at all corners orassembled with corner fittings. Gates assembled with cornerfittings shall have adjustable truss rods516 in. (7.9 mm)minimum diameter on p
8、anels 5 ft (1.5 m) wide or wider. Trussrods shall be the same base metal and finish as the gate frames.4.1.1 The interior bracing, when needed, shall be the samemetal and shape tubular material and finish as the gate frame,but need not be the same size.4.2 ManufactureGate frames shall be fabricated
9、andcoated where necessary, as described in 4.2.1 through 4.2.5.For gates intended to be automated, manufacture shall conformto the applicable provisions of Specification F2200.4.2.1 Zinc-Coated Steel Frames shall be in accordance withSpecifications F1043 or F1083, or a combination thereof, andshall
10、match that selected for any adjoining fence framework.Welded joints shall be coated in accordance with PracticeA780.4.2.2 Polymer-Coated Steel Frames shall be in accordancewith Specification F1043 and shall match that selected for anyadjoining fence framework. Welded joints on polymer-coatedsteel ga
11、te frames shall be coated in accordance with PracticeA780. The painted areas shall then be top-coated to match theframe color.4.2.3 Chain Link Gate FabricThe fabric shall be asspecified for the fence.4.2.4 Barbed Wire TopWhen specified, shall have the endmembers of the gate frame extended in height
12、to accommodatethree strands of barbed wire uniformly spaced and positionedso that the top strand is approximately 1 ft (300 mm) above thetop horizontal member of the gate frame, except that theminimum height for barbed wire installed at the top of gatesintended to be automated shall be in accordance
13、 with Specifi-cation F2200. Barbed wire shall be attached by suitable meansto prevent wire from moving out of position and shall besupported by a gate frame member at maximum intervals of 8ft (2.44 mm).4.2.5 Barbed TapeThe minimum height for barbed tapeinstalled at the top of gates intended to be au
14、tomated shall bea minimum of 8 ft - 0 in.1This specification is under the jurisdiction of ASTM Committee F14 on Fencesand is the direct responsibility of Subcommittee F14.40 on Chain Link Fence andWire Accessories.Current edition approved June 1, 2017. Published July 2017. Originally approvedin 1984
15、. Last previous edition approved in 2011 as F900 - 11. DOI: 10.1520/F0900-11R17.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the standards Document Summary page
16、onthe ASTM website.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United StatesThis international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for theD
17、evelopment of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.15. Dimensions, Mass, and Permissible Variations5.1 Size of the gate opening shall be measured from theinside face to inside face of gate posts.5.2 Dim
18、ensions and weights of gate frame members shall bein accordance with Table 1.5.2.1 Gate frame shall be designed for the width built so thatthe outer member shall not sag in excess of the lesser of 1 % ofthe gate leaf width or 2 in. (50.8 mm).5.2.2 For dimensions and weight of gate posts, see Table 2
19、.6. Gate Accessories6.1 All gate hardware shall be of sufficient strength anddurability to support the gate and repeated open-close cycles.6.2 Gate HingesHinges shall be pressed steel or malleableiron having a minimum zinc coating of 1.2 oz ft2and allow thegate to open and close without binding. The
20、 hinges shall be sodesigned to permit the gate to swing a full 180. The user shallspecify, one of the following directions of swing:6.2.1 180 outward,6.2.2 180 inward,6.2.3 90 in and out.6.3 Single Gate LatchThis latch shall be capable ofretaining the gate in a closed position and shall have provisi
21、onfor a padlock.6.4 Double Gate LatchThis latch shall be a drop rod orplunger bar arranged to engage the gate stop. Locking devicesshall be constructed so that the center drop rod or plunger barcannot be raised when the gate is locked. The latching devicesshall have provision for a padlock.6.5 Gate
22、StopsGate stops shall be provided for all doublegates and shall be suitable for setting in concrete for the centerdrop rod or plunger.6.6 KeepersKeepers shall be provided for each gate leafover 5 ft (1.5 m) wide. Gate keepers shall consist of amechanical device for securing the free end of the gate
23、when infull open position.6.7 All gate accessories to have a minimum zinc coating of1.2 oz ft2.6.8 All gate posts shall be of sufficient strength so that thetotal deflection of the gate frame and the gate post at the end ofthe gate leaf shall not exceed the lesser of 2 % of the gate leafwidth or 4 i
24、n. When necessary to meet this requirement due tothe total weight of the gate leaf the next larger size post listedin Table 2 shall be used.7. Keywords7.1 drop rod; gate leaf; hinges; keepers; latch; plunger;polymer; truss rodsTABLE 1 Gate Frame Members, Dimensions, and WeightsNOTE 1Gate leaf shall
25、have vertical interior bracing at maximum intervals of 8 ft and shall have a horizontal interior member if fabric height is 8ft or more. Additional horizontal, vertical or diagonal member or diagonal truss rods may be needed to comply with requirements of 5.2.1.Gate Fabric Height OutsideDimensions,i
26、n. (mm)Minimum Weight,lb/ft (kg/m)6 ft (1.8 m) or Less:Round tubular (steel) 1.66 (42.2) 1.83 (2.72)Rectangular tubular (steel) 2.00 (50.81) 2.52 (3.75)Over 6 ft (1.8 m):Round tubular (steel) 1.90 (48.3) 2.28 (3.39)Rectangular tubular (steel) 2.00 (50.8) 2.52 (3.75)Interior Bracing:Round pipe (steel
27、) 1.66 (42.2) 1.83 (3.39)Rectangular pipe (steel) 1.50 (38.1) 1.84 (2.74)F900 11 (2017)2ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of
28、 the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn.
29、Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comme
30、nts have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or m
31、ultiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the Copyright Clearance
32、 Center, 222Rosewood Drive, Danvers, MA 01923, Tel: (978) 646-2600; http:/ 2 Typical Dimensions and Weight of Gate PostsNOTE 1It is recommended that any questions regarding deflection of post be directed to the post manufacturer.Gate Leaf Width Outside Diameterof Pipe, in. (mm)Minimum Weight,lb/ft (
33、kg/m)For Gate Fabric Height of 6 ft (1.8 m) or less:Up to and including 4 ft. (1.2 m) Steel 2.375 (60.3) 3.11 (4.63)Over 4 to 10 ft (1.2 to 3.7 m) Steel 2.875 (73.0) 4.64 (6.91)Over 10 to 18 ft (3.7 to 5.5 m) Steel 4.000 (101.6) 6.56 (9.77)For Gate Fabric Height Over 6 ft (1.8 m):Up to and including 6 ft (1.8 m) Steel 2.875 (73.0) 4.64 (7.04)Over 6 to 12 ft (1.8 to 3.7) Steel 4.000 (101.6) 6.56 (9.77)Over 12 to 18 ft (3.7 to 5.5 m) Steel 6.625 (168.3) 18.02 (26.82)Over 18 to 24 ft (5.5 to 7.3 m) Steel 8.625 (219.1) 27.12 (40.36)F900 11 (2017)3
