1、Designation: F2088 11Standard Consumer Safety Specification forInfant Swings1This standard is issued under the fixed designation F2088; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parenthe
2、ses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONThis consumer safety specification addresses infant swing incidents identified by the U.S. ConsumerProduct Safety Commission (CPSC).In response to incide
3、nt data compiled by the CPSC, this consumer safety specification attempts tominimize the following: (1) swings tipping over or collapsing, (2) structural failures, and (3)entanglement in the restraints or entrapment in leg holes. This consumer safety specification isintended to cover normal use and
4、reasonably foreseeable misuse or abuse of infant swings. Thisspecification does not cover swings that are blatantly misused or used in a careless manner thatdisregards the safety instructions and warnings provided with each infant swing.This consumer safety specification is written within the curren
5、t state-of-the-art of infant swingtechnology and will be updated whenever substantive information becomes available that necessitatesadditional requirements or justifies the revision of existing requirements.1. Scope1.1 This consumer safety specification establishes safetyperformance requirements, t
6、est methods, and labeling require-ments to minimize the hazards to infants presented by swingsas identified in the introduction.1.2 This consumer safety specification is intended to mini-mize the risk of injuries to infants resulting from normal useand reasonably foreseeable misuse or abuse of infan
7、t swings. Itis not intended to address all incidents and injuries resultingfrom the interaction of other persons with the infant in theswing.1.3 No swing produced after the approval date of thisconsumer safety specification shall, either by label or othermeans, indicate compliance with this specific
8、ation unless itconforms to all requirements contained herein.1.4 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 The following precau
9、tionary caveat pertains only to thetest method portion, Section 7, of this consumer safety speci-fication: This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and h
10、ealth practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D3359 Test Methods for Measuring Adhesion by Tape TestF963 Consumer Safety Specification for Toy Safety2.2 Federal Standards:16 CFR Part 1303 Ban of Lead-Containing Pain
11、t andCertain Consumer Products Bearing Lead-ContainingPaint316 CFR Part 1500 Hazardous Substances Act Regulationsincluding sections:1500.48Technical Requirements for Determining aSharp Point in Toys or Other Articles Intended for Use byChildren Under Eight Years of Age31500.49Technical Requirements
12、for Determining aSharp Metal or Glass Edge in Toys or Other ArticlesIntended for Use by Children Under Eight Years of Age31500.50-.51Test Method for Simulating Use and Abuseof Toys and Other Articles Intended for Use by Children316 CFR Part 1501 Method for Identifying Toys and OtherArticles Intended
13、 for Use by Children Under Three Yearsof Age Which Present Choking, Aspiration, or Ingestion1This consumer safety specification is under the jurisdiction of ASTM Commit-tee F15 on Consumer Products and is the direct responsibility of SubcommitteeF15.21 on Infant Carriers, Bouncers and Baby Swings.Cu
14、rrent edition approved Feb. 1, 2011. Published March 2011. Originallyapproved in 2001. Last previous edition approved in 2009 as F2088 09. DOI:10.1520/F2088-11.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of
15、 ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401.1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C70
16、0, West Conshohocken, PA 19428-2959, United States.Hazards Because of Small Parts32.3 Other Documents:CAMI Infant Dummy, Mark II (see Fig. 1)4CAMI Newborn Dummy (see Fig. 2)53. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 conspicuous, na label which is visible, when theunit is
17、 in a manufacturers recommended use position, to aperson standing near the unit at any one position around theinfant swing but not necessarily visible from all positions.3.1.2 cradle swing, nan infant swing which is intendedfor use by a child lying flat.3.1.3 dynamic load, napplication of impulsive
18、forcethrough free fall of a weight.3.1.4 infant swing, na stationary unit with a frame andpowered mechanism that enables an infant to swing in a seatedposition. An infant swing is intended for use with infants frombirth until a child is able to sit up unassisted.3.1.5 manufacturers recommended use p
19、osition, nanyposition, that is presented as a normal, allowable, or acceptableconfiguration for the use of the product by the manufacturer inany descriptive or instructional literature. This specificallyexcludes positions that the manufacturer shows in a likemanner in its literature to be unacceptab
20、le, unsafe, or notrecommended.3.1.6 non-paper label, nany label material (such as plasticor metal) which either will not tear without the aid of tools ortears leaving a sharply defined edge.3.1.7 occupant, nthat individual who is in a product thatis set up in one of the manufacturers recommended use
21、positions.3.1.8 paper label, nany label material which tears withoutthe aid of tools and leaves a fibrous edge.3.1.9 static load, na vertically downward force applied bya calibrated force gage or by dead weights.3.1.10 structural component, nany load bearing memberor part of the product that support
22、s the weight or portion of theweight of the occupant.3.1.11 travel swing, na low profile, compact swing havinga distance of 6 in. or less between the underside of the seatbottom and the support surface (floor) at any point in the seatsrange of motion.4. Calibration and Standardization4.1 All testing
23、 shall be conducted on a concrete floor thatmay be covered with18 in. (3 mm) thick vinyl floor covering,unless test instructs differently.4.2 The product shall be completely assembled, unlessotherwise noted, in accordance with the manufacturers in-structions.4.3 No testing shall be conducted within
24、48 h of manufac-turing.4.4 The product to be tested shall be in a room with anambient temperature of 73 6 9F (23 6 5C) for at least 1hour prior to testing. Testing then shall be conducted withinthis temperature range.4.5 All testing required by this specification shall be con-ducted on the same unit
25、.5. General Requirements5.1 Hazardous Sharp Edges or PointsThere shall be nohazardous sharp points or edges as defined by 16 CFR 1500.48and 16 CFR 1500.49 before and after testing to the consumersafety specification.5.2 Small PartsThere shall be no small parts as defined by16 CFR 1501 before testing
26、 or liberated as a result of thistesting to this specification.5.3 The paint and surface coating on the product shallcomply to 16 CFR 1303.5.4 Wood PartsPrior to testing, any exposed wood partsshall be smooth and free from splinters.4Department of Transportation Memorandum Report AAC-119-74-14, Revi
27、sionII, Drawing No. SA-1001 by Richard Chandler, July 2, 1974. Federal AviationAdministration, Civil Aeromedical Institute, Protection and Survival Laboratory,Aeromedical Center, Oklahoma City, OK 73125.5Drawing numbers 126-0000 through 126-0015 (sheets 1 through 3), 126-0017through 126-0027, a part
28、s list entitled “Parts List for CAMI Newborn Dummy”, anda construction manual entitled, “Construction of the Newborn Infant Dummy” (July1992). Copies of the materials may be inspected at NHTSAs Docket Section, 400Seventh Street, SW., Room 5109, Washington, DC, or at the Office of the FederalRegister
29、, 800 North Capitol Street, NW., suite 700, Washington, DC.FIG. 1 CAMI Infant Dummy, Mark IIFIG. 2 CAMI Newborn DummyF2088 1125.5 Scissoring, Shearing, PinchingAproduct, when in themanufacturers recommended use position, shall be designedand constructed so as to prevent injury to the occupant froman
30、y scissoring, shearing, or pinching when members or com-ponents rotate about a common axis or fastening point, slide,pivot, fold or otherwise move relative to one another. Scissor-ing, shearing, or pinching that may cause injury could existwhen the edges of any rigid parts admit a probe greater than
31、0.210 in. (5.33 mm) and less than 0.375 in. (9.53 mm) diameterat any accessible point throughout the range of motion of suchparts.5.6 OpeningsHoles or slots that extend entirely though awall section of any rigid material less than 0.375-in. (9.53-mm)thick and admit a 0.210-in. (5.33-mm) diameter rod
32、 shall alsoadmit a 0.375-in. (9.53-mm) diameter rod. Holes or slots thatare between 0.210-in. (5.33-mm) and 0.375-in. (9.53-mm) andhave a wall thickness less than 0.375-in. (9.53-mm), but arelimited in depth to 0.375-in. (9.53-mm) maximum by anotherrigid surface shall be permissible (see Fig. 3). Th
33、e product shallbe evaluated in all manufacturers recommended use positions.5.7 Exposed Coil SpringsAny exposed coil spring whichis accessible to the occupant, having or capable of generatinga space between coils of 0.210 in (5.33 mm) or greater duringstatic load testing (see 7.2.2) shall be covered
34、or otherwisedesigned to prevent injury from entrapment.5.8 Protective ComponentsIf a child can grasp compo-nents between the thumb and forefinger, or teeth, (such as caps,sleeves, or plugs used for protection from sharp edges, points,or entrapment of fingers or toes), or if there is at least a 0.040
35、in. (1.00 mm) gap between the component and its adjacentparent component, such component shall not be removed whentested in accordance with 7.1.5.9 Labeling:5.9.1 Warning labels, (whether paper or non paper) shall bepermanent when tested per 7.7.5.9.2 Warning statements applied directly onto the sur
36、faceof the product by hot stamping, heat transfer, printing, woodburning, etc. shall be permanent when tested per 7.8.5.9.3 Non-paper labels shall not liberate small parts whentested in accordance with 7.9.5.10 ToysToy accessories attached to, removable from, orsold with an infant swing, as well as
37、their means of attachment,must meet applicable requirements of Consumer Safety Speci-fication F963.FIG. 3 Opening ExamplesF2088 1135.10.1 Toy mobiles that attach solely to an infant swing arenot required to contain labeling as stated in Consumer SafetySpecification F963, Section 5.6.2 Safety Labelin
38、g Mobiles and6.3 Instructional Literature Mobiles.6. Performance Requirements6.1 Structural IntegrityAll tests that cover static anddynamic loading are to be performed sequentially on the sameproduct and in the sequence listed in the standard.6.1.1 Dynamic LoadThe swing shall support a dynamicload a
39、nd there shall be no failure of seams, breakage ofmaterials, or changes of adjustments that could cause theproduct to not fully support the child or create a hazardouscondition as defined in Section 5 after testing in accordancewith 7.2.1.6.1.2 Static LoadThe swing shall support a static load andthe
40、re shall be no failure of seams, breakage of materials, orchanges of adjustments that could cause the product to not fullysupport the child or create a hazardous condition as defined inSection 5 after testing in accordance with 7.2.2.6.2 Stability TestThe swing shall not tip over when testedaccordin
41、g to 7.3.6.3 Unintentional FoldingThe swing shall remain in themanufacturers recommended use position when tested per 7.4.If a unit is designed with a latching or locking device, thatdevice shall remain engaged and operative after testing.6.3.1 Threaded fasteners used to attach structural compo-nent
42、s shall have a locking mechanism such as lock washers,self-locking nuts or other means to prevent detachment due tovibration.6.4 Restraint SystemA restraint system shall be providedto secure a child in the seated positions in any of themanufacturers recommended use positions.6.4.1 The restraint syst
43、em shall include both waist andcrotch restraint designed such that the crotch restraints use ismandatory when the restraint system is in use.6.4.2 This system and its closing means shall not slip morethan 1 in. (25 mm), break, separate, or permit the removal ofthe test dummy when tested per 7.5.6.4.
44、3 A connecting means and adjustment means for thewaist restraint shall be capable of usage independent of oneanother. The connecting means shall not be an adjustmentmeans but may have one integrally attached to it.6.4.4 Before shipment, the restraint system must be attachedto the swing in such a man
45、ner as to not become detachedthrough normal use.6.4.5 If the swing seat has a tray or other component thatcreates a completely bounded opening in front of the occupant,a passive crotch restraint system shall be included and designedsuch that its use is mandatory when the tray or other compo-nent is
46、in use.6.5 Passive Crotch Restraint SystemFor products with atray or other component that creates a completely boundedopening in front of the occupant.6.5.1 There shall be no vertical gap between the passivecrotch restraint and either the tray or seating surface that allowsfree passage of a 1.5-in.
47、(38-mm) diameter by 3-in. (76-mm)long rod from one leg opening to the other.6.5.2 The leg openings on each side of the passive crotchrestraint shall not allow complete passage of the wedge blockwhen tested in accordance with 7.10.6.6 Cradle Swing OrientationThe angle of the cradleswing surface along
48、 the dummys head-to-toe axis relative tothe horizontal shall not be greater than 5 degrees when testedin accordance to 7.6.6.7 Swings Containing Battery Compartment(s) (remotecontrol devices are exempt from the requirements in 6.7):6.7.1 Each battery compartment or area immediately adja-cent to the
49、battery compartment shall be marked permanentlyand legibly to show the correct battery polarity, size, andvoltage.6.7.2 Each battery compartment shall provide a means tocontain the electrolytic material in the event of a batteryleakage. This containment means shall not be accessible to theoccupant.6.7.3 Positive protection from the possibility of chargingany primary (non-rechargeable) battery shall be achieved eitherthrough physical design of the battery compartment or throughthe use of appropriate electrical circuit design. This appli
