1、Designation: F2591 06 (Reapproved 2013)Standard Specification forBearing, Roller, Tapered, Single Row of Rollers (MetricSeries)1This standard is issued under the fixed designation F2591; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revisi
2、on, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.This standard has been approved for use by agencies of the Department of Defense.1. Scope1.1 This specification co
3、vers requirements for metric series,tapered roller bearings with a single row of rollers.1.2 Intended UseThe bearings covered in this specifica-tion are intended to be used in general industrial and vehicleapplications where the operating temperature does not exceed120C (250F).1.3 This specification
4、 contains many of the requirements ofDS3225, which was originally developed by the Department ofDefense and maintained by the Defense Supply Center inRichmond. The following government activity codes may befound in the Department of Defense, Standardization DirectorySD-1.2Preparing Activity Custodia
5、ns Review ActivitiesDLA-GS4 Army-AT Army-AVNavy-MC Navy MC, SHAir Force-99 Air Force-84Other-NS1.4 The values stated in SI units are to be regarded asstandard. No other units of measurement are included in thisstandard.1.5 This standard does not purport to address all of thesafety concerns, if any,
6、associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ABMA Standard:3ABMA 19.1 Tapered Roller BearingsRadial, Metric De-sig
7、n2.2 ISO Standard:4ISO 5593 Rolling BearingsVocabulary2.3 Military Standard:5MIL-C-11796 Corrosion Preventative Compound,Petrolatum, Hot Application2.4 SAE Standard:6SAE AMS-STD-66 Steel: Chemical Composition and Hard-enability3. Terminology3.1 Definitions:3.1.1 For definitions of terms used in this
8、 specification referto ISO 5593.3.1.2 effective load centerdimension (a) locates a point onthe inner ring (cone) axis that is the center of pressure of allresisting forces set up by the bearing rollers. All momentsshould be calculated from this point when determining bearingloading and shaft stresse
9、s. A minus value of (a) indicates thatthe center is inside the inner ring (cone) backface.3.1.3 K factorthe K Factor is the ratio of the basic radialdynamic load rating to the basic static load rating.3.1.4 contact anglethese bearing have a contact angle ()between 10 and 19 degrees. The contact angl
10、e is the anglebetween the line of action of the roller load and a planeperpendicular to the bearing axis.4. Ordering Information4.1 Procurement documents should specify the following:4.1.1 Title, number, and date of this specification,4.1.2 Part Number (see 8.1),4.1.3 Nominal dimensions of bearing (
11、bore, outsidediameter, bearing width),4.1.4 Quantity required,4.1.5 Inspection records required, and1This specification is under the jurisdiction ofASTM Committee F34 on RollingElement Bearings and is the direct responsibility of Subcommittee F34.04 onAutomotive/Industrial Bearing.Current edition ap
12、proved May 1, 2013. Published October 2013. Originallypublished in 2006. Last previous edition approved as F2591 06. DOI: 10.1520/F2591-06R13.2The Military codes that are listed in SD-1 give the address and phone numbersof the DoD contacts. These are found in the DoDs ASSIST website http:/assist.dap
13、s.dla.mil/online/start/.3Available from Techstreet, 777 E. Eisenhower Parkway,AnnArbor , MI 48108.4Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036.5Available from the DODs Assist internet site located at: http:/assist.daps.dla.mil/online/star
14、t/.6Available from Society of Automotive Engineers (SAE), 400 CommonwealthDr., Warrendale, PA 15096-0001.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States14.1.6 Required packaging.5. Materials and Manufacture5.1 Material:5.1.1 Outer Rin
15、g (Cup), Inner Ring (Cone) and RollersBearing quality, carburizing grade alloy or through-hardening grade alloy steel in accordance with SAE AMS-STD-66.5.1.2 CageCarbon steel (stamped) or powdered processsteel (for example, Sinta Forge) may be used.6. Physical Properties6.1 HardnessOuter ring (cup),
16、 inner ring (cone) androllers shall be hardened to 58 to 64 HRC.7. Dimensions, Mass, and Permissible Variations7.1 Dimensions:7.1.1 Dimensions Db,Da,db,daare recommended shaft andhousing shoulder diameters.7.1.2 Dimensions R and r are the maximum fillet radii onthe shaft and the housing respectively
17、, which will be cleared bythe bearing corner. See Fig. 1 and Table 1.7.2 TolerancesPrecision grade (Class B) shall be specifiedonly when technically justified.7.2.1 Standard Grade (Class K)See Tables 2-5.7.2.2 Precision Grade (Class B)See Tables 6-9.7.3 Cage Clearance Designers should provide a clea
18、ranceof 3.2 mm minimum between the outside edge of the cage andthe housing counterbore.8. Part Number8.1 Part NumberThe Part number shall consist ofDS3225, followed by the dash number, followed by -K for astandard grade bearing or -B for a precision grade bearing.8.1.1 Examples:8.1.1.1 DS3225-15-K i
19、s a standard grade, 75 mm bore, 145mm OD, 51 mm wide single row tapered roller bearing.8.1.1.2 DS3225-15-B is a precision grade, 75 mm bore, 145mm OD, 51 mm wide single row tapered roller bearing.8.1.2 The ABMA (American Bearing Manufacturers Asso-ciation) outer and inner numbers are for reference o
20、nly and arenot to be used for ordering purposes.9. Lubrication9.1 LubricationUnless specified otherwise, bearings shallbe furnished without lubrication.10. Preservation, Packaging and Packing10.1 Packaging and packing shall be as specified in theacquisition document.10.2 Preservation:10.2.1 Commerci
21、al UseManufacturer shall coat bearingwith rust preventative film.10.2.2 DoD UseUnless specified otherwise, bearings shallbe furnished with preservative in accordance with MIL-C-11796, Class 3.11. Keywords11.1 bearing; DS3225; single row bearing; tapered rollerbearingFIG. 1 Schematic Drawing, Metric
22、Series, Single Row, Tapered Roller BearingF2591 06 (2013)2TABLE 1 Metric Series, Single Row, Tapered Roller Bearing DimensionsDashNo.ABMABearing Number(see 8.1)Outer Inner(Cup) (Cone)dDTBCRrdbdaDbDaKFactorBasicDynamicLoad Rating(kN)aBore O.D.Brg.WidthInner(Cone)WidthOuter(Cup)WidthMax.ShaftFilletRad
23、.Max.Hsg.FilletRad.RecommendedShoulder DiameterEff.LoadCenterShaft Housing Radial Thrust1 JLM104948-JLM104910 50 82 21.5 21.5 17.0 3.0 0.5 60 55.0 76 78.0 1.91 15.0 7.85 -5.42 JM205149-JM205110 50 90 28.0 28.0 23.0 3.0 2.5 63 57.0 80 85.0 1.78 22.2 12.45 -7.63 JHM807045-JHM807012 50 105 37.0 36.0 29
24、.0 3.0 2.5 69 63.0 90 100.0 1.20 31.8 26.6 -7.54 JLM506849-JLM506810 55 90 23.0 23.0 18.5 1.5 0.5 63 61.0 82 86.0 1.45 16.85 11.65 -2.85 JM207049-JM207010 55 95 29.0 29.0 23.5 1.5 2.5 64 62.0 85 91.0 1.74 24.0 13.8 -7.66 JH307749-JH307710 55 110 39.0 39.0 32.0 3.0 2.5 71 64.1 97 104.0 1.69 37.8 22.4
25、 -11.77 JLM508748-JLM508710 60 95 24.0 24.0 19.0 5.0 2.5 75 66.0 85 91.0 1.45 18.2 12.6 -2.78 JLM710949-JLM710910 65 105 24.0 23.0 18.5 3.0 1.0 78 72.0 96 100.5 1.29 19.8 15.35 -0.39 JM511946-JM511910 65 110 28.0 28.0 22.5 3.0 2.5 78 72.0 99 105.0 1.45 26.2 18.0 -3.410 JH211749-JH211710 65 120 39.0
26、38.5 32.0 3.0 2.5 80 74.0 107 114.0 1.73 41.0 23.6 -10.811 JLM813049-JLM813010 70 110 26.0 25.0 20.5 1.0 2.5 78 77.0 98 105.0 1.20 22.0 18.2 +0.412 JM612949-JM612910 70 115 29.0 29.0 23.0 3.0 2.5 83 77.0 103 110.0 1.36 27.4 20.2 -2.513 JLM714149-JLM714110 75 115 25.0 25.0 19.0 3.0 2.5 87 81.0 104 11
27、0.0 1.27 22.0 17.3 +0.414 JM714249-JM714210 75 120 31.0 29.5 25.0 3.0 2.5 88 82.9 108 115.0 1.31 30.2 23.0 -2.015 JH415647-JH415610 75 145 51.0 51.0 42.0 3.0 2.5 94 89.0 129 139.0 1.61 65.5 40.6 -14.416 JM515649-JM515610 80 130 35.0 34.0 28.5 3.0 2.5 94 88.0 117 125.0 1.50 38.0 25.4 -5.217 JM716649-
28、JM716610 85 130 30.0 29.0 24.0 3.0 2.5 98 92.0 117 125.0 1.31 31.6 24.0 -0.218 JHM516849-JHM516810 85 140 39.0 38.0 31.5 3.0 2.5 100 94.0 125 134.0 1.43 45.5 32.0 -5.919 JH217249-JH217210 85 150 46.0 46.0 38.0 3.0 2.5 101 95.0 134 142.0 1.76 62.0 35.2 -11.920 JM718149-JM718110 90 145 35.0 34.0 27.0
29、3.0 2.5 106 99.0 131 138.8 1.31 42.0 32.0 -2.021 JHM318448-JHM318410 90 155 44.0 44.0 35.5 3.0 2.5 106 100.0 140 148.0 1.71 61.0 35.8 -10.022 JM719149-JM719113 95 150 35.0 34.0 27.0 3.0 2.5 109 104.0 135 143.0 1.32 41.6 31.6 -1.623 JM720249-JM720210 100 155 36.0 35.0 28.0 3.0 2.5 115 109.0 140 149.0
30、 1.24 44.8 36.2 +0.324 JHM720249-JHM720210 100 160 41.0 40.0 32.0 3.0 2.5 117 109.4 143 153.9 1.24 54.5 43.8 -2.525 JM822049-JM822010 110 165 35.0 35.0 26.5 3.0 2.5 125 119.0 149 159.0 1.18 45.0 38.2 +3.026 JHM522649-JHM522610 110 180 47.0 46.0 38.0 3.0 2.5 127 122.0 162 172.0 1.44 72.0 50.0 -6.027
31、JHM534149-JHM534110 170 230 39.0 38.0 31.0 3.0 2.5 184 178.0 217 224.0 1.52 69.0 45.5 +4.628 JM344449-JM734410 170 240 46.0 44.5 37.0 3.0 2.5 185 180.0 222 232.0 1.34 88.5 66.0 +5.029 JM736149-JM736110 180 250 47.0 45.0 37.0 3.0 2.5 196 190.5 232 242.6 1.22 91.5 75.0 +9.030 JM738249-JM738210 190 260
32、 46.0 44.0 36.5 3.0 2.5 206 200.0 242 252.0 1.22 85.5 70.0 +10.831 JHM840449-JHM840410 200 300 65.0 62.0 51.0 3.5 2.5 223 214.8 273 288.9 1.12 147.5 132.0 +8.1TABLE 2 Inner Ring (Cone) Bore Tolerance (Class K)Inner Ring Bore (d)Size Range,mmTolerance,mOver Incl. Plus Minus30 50 0 -1250 80 0 -1580 12
33、0 0 -20120 180 0 -25180 250 0 -30TABLE 3 Outer Ring (Cup) Outside Diameter Tolerance (Class K)Outer Ring O.D. (D)Size Range,mmTolerance,mOver Incl. Plus Minus80 120 0 -18120 150 0 -20150 180 0 -25180 250 0 -30250 315 0 -35TABLE 4 Bearing Overall Width Tolerance (Class K)Bearing Width (T)Bore Size Ra
34、nge,mmTolerance,mOver Incl. Plus Minus18 80 200 080 120 200 -200120 250 350 -250TABLE 5 Maximum Radial Runout of Assembled Bearing(Class K)Maximum Radial RunoutOuter Ring O.D. (D),mmTolerance,mOver Incl.80 180 35120 150 40150 180 45180 250 50250 315 60F2591 06 (2013)3APPENDIX(Nonmandatory Informatio
35、n)X1. BEARING LOAD RATINGS AND RATING LIFEX1.1 Basic Dynamic Load RatingX1.1.1 The Basic Dynamic Load Rating is that constantstationary load which a group of apparently identical bearingswith stationary outer rings (cups) can endure for a rating life of90 million revolutions of the inner ring (cone)
36、. The basicdynamic load ratings listed herein are based on a rated life of90 million revolutions or 3000 h at 500 revolutions per min.X1.1.2 To compare the load ratings in this specification withother load ratings whose basis for ratings are other than 90million revolution or 3000 h at 500 rpm, use
37、the followingformula:C 5 Other Bearing Load Rating 3 R1/500!1/f3 H1/3000!1/f(X1.1)where:R1= rotational speed (in rpm) at which other bearing israted,H1= hours at which other bearing is rated, andf = other bearing fatigue factor.X1.2 Rating Life (Hours)X1.2.1 The rating life is the number of hours at
38、 someconstant speed of the inner ring (cone) that 90 % of a group ofTABLE 6 Inner Ring (Cone) Bore Tolerance (Class B)Inner Ring Bore (d)Size Range,mmTolerance,mOver Incl. Plus Minus30 50 0 -850 80 0 -980 120 0 -10120 180 0 -13180 315 0 -15TABLE 7 Outer Ring (Cup) Outside Diameter Tolerance (Class B
39、)Outer Ring (Cup) O.D. (D)Size Range,mmTolerance,mOver Incl. Plus Minus80 120 0 -10120 150 0 -11150 180 0 -13180 250 0 -15250 315 0 -18TABLE 8 Bearing Overall Width Tolerance (Class B)Bearing Width (T)Bore Size Range,mmTolerance,mOver Incl. Plus Minus18 120 200 -200120 180 200 -250180 250 200 -300TA
40、BLE 9 Maximum Radial Runout of Assembled Bearing(Class B)Maximum Radial RunnoutOuter Ring O.D. (D),mmTolerance,mOver Incl.80 180 4.0180 315 5.0F2591 06 (2013)4apparently identical bearings will complete or exceed beforefirst evidence of fatigue develops. The magnitude of the ratedlife in hours is fo
41、und from the following:L10 5 1.5 3106!/R# 3 C/P!10/3h (X1.2)where:C = basic dynamic load rating,P = equivalent load (combined radial and thrust load) kN,andR = rotational speed, in revolutions per minute.X1.2.2 The average life is approximately four times therated life.ASTM International takes no po
42、sition respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibi
43、lity.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to A
44、STM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the addres
45、s shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F2591 06 (2013)5
