1、Designation: F2607 08 (Reapproved 2014) An American National StandardStandard Test Method forMeasuring the Hard Surface Floor-Cleaning Ability ofHousehold/Commercial Vacuum Cleaners1This standard is issued under the fixed designation F2607; the number immediately following the designation indicates
2、the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This test method provides only a laboratory test
3、 fordetermining the relative hard surface floor-cleaning ability ofhousehold/commercial vacuum cleaners when tested underspecified test conditions.1.2 This test method is applicable to household/commercialtypes of upright, canister, combination, and stick vacuumcleaners that use a dry primary dirt r
4、eceptacle and are intendedfor cleaning hard surface floors as a primary or secondaryfunction.1.3 This test method applies only to the removal of drydebris from hard surface floors, not the removal of embeddeddirt from carpet.1.4 The values stated in inch-pound units are to be regardedas standard. Th
5、e values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not considered standard.1.5 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard t
6、o establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D75 Practice for Sampling AggregatesE177 Practice for Use of the Terms Precision and Bias inASTM Test MethodsE691 Practice for Condu
7、cting an Interlaboratory Study toDetermine the Precision of a Test Method2.2 IEC Standard:3IEC 60312 Vacuum Cleaners for Household UseMethodsof Measuring the Performance3. Terminology3.1 Definitions:3.1.1 cleaning ability, nrelative ease with which soils orstains can be removed from material.3.1.2 m
8、odel, ndesignation of a group of vacuum cleanershaving identical mechanical and electrical construction withonly cosmetic or nonfunctional differences.3.1.3 population, ntotal of all units of a particular modelvacuum cleaner being tested.3.1.4 repeatability limit (r), nvalue below which theabsolute
9、difference between two individual test results obtainedunder repeatability condition may be expected to occur with aprobability of approximately 0.95 (95 %).3.1.5 repeatability standard deviation (Sr), nstandard de-viation of test results obtained under repeatability conditions.3.1.6 reproducibility
10、 limit (R), nvalue below which theabsolute difference between two test results obtained underreproducibility conditions may be expected to occur with aprobability of approximately 0.95 (95 %).3.1.7 reproducibility standard deviation (SR), nstandarddeviation of test results obtained under reproducibi
11、lity condi-tions.3.1.8 sample, ngroup of vacuum cleaners taken from alarge collection of vacuum cleaners of one particular modelwhich serves to provide information that may be used as a basisfor making a decision concerning the larger collection.3.1.9 test run, ndefinitive procedure that produces a
12、sin-gular measured result.3.1.10 unit, nsingle vacuum cleaner of the model beingtested.1This test method is under the jurisdiction ofASTM Committee F11 on VacuumCleaners and is the direct responsibility of Subcommittee F11.21 on Cleanability.Current edition approved Nov. 1, 2014. Published November
13、2014. Originallyapproved in 2006. Last previous edition approved in 2008 as F2607 08. DOI:10.1520/F2607-08R14.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information, refer to the st
14、andards Document Summary page onthe ASTM website.3Available from International Electrotechnical Commission (IEC), 3 rue deVaremb, Case postale 131, CH-1211, Geneva 20, Switzerland, http:/www.iec.ch.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. Un
15、ited States14. Significance and Use4.1 This test method will provide an indication of the abilityof the vacuum cleaner in removing dry debris from hardsurface floors. The cleaning ability in the laboratory test willnot be the same as in home cleaning; however, in most cases,a vacuum cleaner that per
16、forms well in the laboratory willclean well in a home.4.2 To provide a uniform basis for measuring the perfor-mance described in 1.1, standardized test hard surface flooringand standardized test debris are used.5. Apparatus5.1 Weighing Scale for Weighing Cleaners, accurate to0.035 oz (1 g) and havin
17、g a weighing capacity of at least 15 lb(6.82 kg).5.2 Weighing Scale for Weighing Test Dirt and DirtContainer, accurate to 0.0035 oz (0.10 g) and having aweighing capacity of at least 1.1 lb (500 g).5.3 Stopwatch, with a second hand or other type of equip-ment capable of establishing the specified ra
18、te of movementand total cycle time of the vacuum cleaner.5.4 Voltmeter, to measure input volts to the vacuum cleanerand provide measurements accurate to within 61%.5.5 Voltage-Regulator System, to control the input voltageto the vacuum cleaner. The regulator shall be capable ofmaintaining the vacuum
19、 cleaners rated voltage 61 % andrated frequency 61 Hz having a waveform that is essentiallysinusoidal with 3 % maximum harmonic distortion for theduration of the test.5.6 Debris DispenserAny convenient dispensing systemthat provides the operator with a method to distribute the testdebris uniformly o
20、ver the test area.5.7 Hard Surface FloorAny smooth (minimal texture, noseams) vinyl floor covering. Flooring to be glued to a plywoodsupporting surface over the whole area. Plywood supportingsurface to be a flat surface consisting of a piece of34-in.(19-mm) thick exterior-grade plywood with the “A”
21、surfaceupward to support the test surface.5.8 Template, to standardize the debris area for each cleanertested. Debris area to be 27.6 in. (70 cm) long (stroke direction)with a width equal to 0.8 in. (2 cm) less than the outside widthof the vacuum cleaner floor nozzle.5.9 Temperature and Humidity Ind
22、icators, to provide tem-perature measurements accurate to within 61F (612 C) andhumidity measurements accurate to within 2 % relative humid-ity.5.10 Guide Rails, similar to those described in IEC 60312may be used to facilitate straight line movement of the cleanerover the test area. The use of guide
23、 rails is optional. See Fig. 1.NOTE 1Automated methods for spreading the test debris and cleaningthe surface are acceptable if they do not change the results of this testmethod.6. Materials6.1 Silica Sand, Sieve Size Range, 40/+50 at a density of0.0167 g/in.2(0.002 59 g/cm2). Sieving is suggested to
24、 get thecorrect size.46.2 Oatmeal, uncooked at a density of 0.0167 g/in.2(0.00259 g/cm2).6.3 Baking Soda, USP#1 at a density of 0.0167 g/in.2(0.00259 g/cm2).6.4 Orzo Pasta (elliptical shape, not teardrop shape), at adensity of 0.0167 g/in.2(0.002 59 g/cm2).7. Sampling7.1 A minimum of three units of
25、the same model vacuumcleaner selected at random in accordance with good statisticalpractice shall constitute the population sample.7.1.1 To determine the best estimate of cleaning ability forthe population of the vacuum cleaner model being tested, thearithmetic mean of the cleaning ability rating of
26、 the samplefrom the population shall be established by testing it to a 90 %confidence level within 65 % of the mean value of thecleaning ability rating.7.1.2 Annex A1 provides a procedural example for deter-mining the 90 % confidence level and when the sample sizeshall be increased.4The test dirt mu
27、st be sieved to ensure conformance with the analysis limits. UseTest Method D75.FIG. 1 Guide RailsF2607 08 (2014)28. Preparation of Test Vacuum Cleaners8.1 New Test Vacuum Cleaners:8.1.1 Preconditioning a New Test Vacuum CleanerRunthe vacuum cleaner in at rated voltage 61 % and ratedfrequency 61 Hz
28、with filters in place.8.1.1.1 Preconditioning Rotating Agitator-type VacuumCleanerIn a stationary position, operate the vacuum cleanerfor 1 h with the agitator bristles not engaged on any surface.8.1.1.2 Preconditioning a Straight-air Canister VacuumCleanerOperate the vacuum cleaner for 1 h with a w
29、ide-openinlet (without hose).8.2 Used Test Vacuum Cleaners:8.2.1 Recondition a used test vacuum cleaner before eachtest run as follows:8.2.1.1 Thoroughly remove excess dirt from the vacuumcleaner. Without using tools for disassembly, clean the entireouter surface, brushes, nozzle chamber, ductwork i
30、nside of thechamber surrounding the primary filter, and inside hose andwands.8.2.1.2 For vacuum cleaners using a disposable filter as theprimary filter, use a new disposable primary filter weighed tothe nearest 0.0035 oz (0.10 g) and install it as recommended bythe vacuum cleaner manufacturer.8.2.1.
31、3 For vacuum cleaners using a nondisposable dirtreceptacle, empty in accordance with the manufacturers in-structions after each test run and clean the receptacle until itsweight is within 0.07 oz (2 g) of its original weight. Weigh thereceptacle to the nearest 0.0035 oz (0.10 g) and install it asrec
32、ommended by the vacuum cleaner manufacturer.8.3 Test Vacuum Cleaner SettingsIf various settings areprovided, set the motor speed setting, suction regulator, nozzleheight, or combination thereof using the manufacturers speci-fications as provided in the instruction manual for hard surfacefloor. Conta
33、ct the manufacturer if no instructions are given orif the instructions are unclear or inadequate.9. Conditioning9.1 Test RoomMaintain the test room in which all condi-tioning and vacuum cleaner testing is done at 70 6 5F (21 63C) and 45 to 55 % relative humidity.9.2 All components involved in the te
34、st shall remain and beexposed in the controlled environment for at least 16 h beforethe start of the test.10. Procedure10.1 Measure the outside width of the floor nozzle of thetest vacuum cleaner. The width measurement is to be taken atthe centerline of the nozzle opening.10.2 Determine the amount o
35、f each type of debris to be usedin the test by multiplying the nozzle width minus 0.8 in. (2 cm)by 27.6 in. (70 cm) and then multiplying this area by the massof debris per unit area given in 6.1 through 6.4.10.2.1 Example:10.2.1.1 Nozzle width equals 13.5 in.10.2.1.2 Debris width equals 12.7 in.10.2
36、.1.3 Debris area equals 12.7 27.6 in. = 350.5 in.2.10.2.1.4 Mass of sand in mixture equals 350.5 in.20.0167 g/in.2= 5.9 g.10.3 Prepare test cleaners and dirt receptacles in accordancewith Section 8.10.4 Clean off the hard surface floor using any method thatensures that the surface is clean and dry.1
37、0.5 Mark the debris area on the test surface such that it iscentered laterally on the test surface (or between the side railsif used). Mark the debris area longitudinally to provide anacceleration/deceleration zone at the start of the forward stroke8 in. (20 cm) long and another acceleration/deceler
38、ation zoneat the end of the forward stroke 12 in. (30 cm) long. See Fig.2. Spread the materials individually within the debris area inthe sequence listed: sand (Layer 1), oatmeal (Layer 2), bakingsoda (Layer 3), and orzo pasta (Layer 4).10.6 Weigh the prepared dirt receptacle (that is, dust bag orot
39、her primary filter device) before conducting the measurementtest run. Record the weight to the nearest 0.0035 oz (0.10 g).10.6.1 For vacuum cleaners with nondisposable dirtreceptacles, weigh and record the receptacles original weightto the nearest 0.0035 oz (0.10 g).10.7 Install the primary filter a
40、s explained in the following:10.7.1 For vacuum cleaners using disposable primary filters,install a new primary filter from the manufacturer in accor-dance with their instructions.10.7.2 For vacuum cleaners using nondisposable primarydirt receptacles, clean the receptacle in accordance with 8.2.1.3an
41、d install it in accordance with the manufacturers instruc-tions.10.8 Ensure that the vacuum cleaner settings have beenmade in accordance with 8.3.10.9 Energize the cleaner for 2 min at nameplate-ratedvoltage 61 % and frequency 61 Hz immediately precedingthe test sequence of 10.11. For cleaners with
42、dual nameplatevoltage ratings, conduct testing at the highest voltage.10.9.1 For a rotating agitator-type vacuum cleaner, place itsuch that the bristles clear the hard surface floor and no loosedebris is picked up.10.9.2 For a straight-air canister vacuum cleaner, operatewith the nozzle unrestricted
43、, positioned such that no loosedebris is picked up from the hard surface floor.10.10 Immediately following the 2-min “run-in” of 10.9,de-energize the vacuum cleaner and place the vacuum cleanernozzle on the hard surface floor so that the front edge of thevacuum cleaner nozzle lip is aligned with the
44、 edge of theacceleration/deceleration zone. See Fig. 2.10.10.1 Reasonable efforts shall be made to maintain thehandle height at 31.5 in. (80 cm) during each test run.10.10.2 Reasonable efforts shall be made to maintain thevacuum cleaners nozzle parallel to the test hard floor surfaceduring each test
45、 run for vacuum cleaners with nonpivotinghandles.10.11 Tilt or lift the nozzle off the hard surface floor,energize the vacuum cleaner, and adjust the voltage to ratedF2607 08 (2014)3voltage 61 %.Allow the vacuum cleaner to run and expand thefilter bag, if one is present. Lower the nozzle before test
46、ingbegins.10.12 Clean with one forward stroke and one backwardstroke at 1.8 ft/s (0.55 m/s). Stop the forward stroke when thefront edge of the nozzle is aligned with the far edge of theacceleration/deceleration zone. Stop the rearward stroke at thesame position as in 10.11.10.13 At the end of the la
47、st stroke, smoothly tilt or lift thevacuum cleaner nozzle off the hard surface floor and allow thevacuum cleaner to run approximately an additional 10 s to clearthe system of test dirt actually picked up but temporarilytrapped in it. Then de-energize the vacuum cleaner. During theadditional run peri
48、od, the hose shall be flexed to help clear thesystem.10.13.1 For vacuum cleaners with removable dirtreceptacles, carefully remove the receptacle and weigh it.Record the weight to the nearest 0.10 g (0.0035 oz).10.14 Determination of the grams picked up for each testrun will be done in the following
49、manner:10.14.1 For vacuum cleaners with removable dirtreceptacles, subtract the weight of the clean dirt receptacle atthe start of the test from the weight of the dirt receptacle at theend of the test. Record results to the nearest 0.10 g (0.0035 oz).10.15 The percent hard surface floor dirt-removal ability fora single test run of a given vacuum cleaner is the mass pickedup (grams) recorded in 10.14.1 divided by the total mass of allfour materials put down (grams) recorded in 10.2, multipliedby 100.10.16 Using the same test vacuum cleaner, repea
