ASTM F2877-2011e1 Standard Test Method for Shock Testing of Structural Insulation of A-Class Divisions Constructed of Steel or Aluminum《钢或铝结构A等级分类的结构绝缘振动测试的标准试验方法》.pdf
《ASTM F2877-2011e1 Standard Test Method for Shock Testing of Structural Insulation of A-Class Divisions Constructed of Steel or Aluminum《钢或铝结构A等级分类的结构绝缘振动测试的标准试验方法》.pdf》由会员分享,可在线阅读,更多相关《ASTM F2877-2011e1 Standard Test Method for Shock Testing of Structural Insulation of A-Class Divisions Constructed of Steel or Aluminum《钢或铝结构A等级分类的结构绝缘振动测试的标准试验方法》.pdf(6页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F2877 111An American National StandardStandard Test Method forShock Testing of Structural Insulation of A-Class DivisionsConstructed of Steel or Aluminum1This standard is issued under the fixed designation F2877; the number immediately following the designation indicates the year oforig
2、inal adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1NOTEEditorially corrected the title in February 2012.TABLE OF CONTENTSIntr
3、oductionSection 1 ScopeSection 2 Referenced DocumentsSection 3 TerminologySection 4 Significance and UseSection 5 Shock Test Prior to Fire Resistance TestSection 6 Criteria to Evaluate Shock Test SpecimenSection 7 Post Shock Fire Resistance TestSection 8 Criteria to Evaluate the Fire Resistance of t
4、he Shock Test SpecimenSection 9 Test ReportSection 10 Precision and BiasSection 11 Key WordsINTRODUCTIONPassive fire protection materials have been required and used on commercial ships for decades. Thepassive systems include the non-combustible insulation material and its means of attachment to ste
5、elor aluminum divisions. The passive system has been evaluated in a standard fire test using a standardsteel or aluminum structural core. No impact loading has been required prior to testing for fireresistance.The United States Navy requires shock testing of passive fire protection prior to fire res
6、istancetesting; this test is defined in MIL-STD-3020, Fire Resistance of U.S. Naval Surface Ships, 7November, 2007. The technology to economically shock test the passive fire protection systems wasdeveloped 50 years ago, and equipment in commercial laboratories is available.After the terrorist attac
7、k on September 11, 2001 it is our responsibility that we add a level of shockprotection to our passive fire protection systems on commercial ships where appropriate.2Many of thepassive fire protection systems used today are mechanically fastened and will perform the intendedfunction after a shock ev
8、ent.Passive fire protection insulation may have thermal or acoustic treatments added to the insulateddivision. These treatments add mass to the fire protection system and their effect on shock is notincluded in this specification.1. Scope1.1 The purpose of the specification is to evaluate insulation
9、installed on steel or aluminum structural division as defined inIMO resolution A.754 (18) to ensure the insulation is notdegraded in the event of a shock.1.2 The non-combustible passive fire protection insulationshall be installed, which will meet the highest level ofcommercial fire resistance expec
10、ted. Lower levels of fireresistance will be allowed without additional shock testing.1.3 This test method is used to measure and describe theresponse of materials, products, or assemblies to heat and flameunder controlled conditions, but does not by itself incorporateall factors required for fire-ha
11、zard or fire-risk assessment of thematerials, products or assemblies under actual fire conditions.1This test method is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.02 onInsulation/Processes.Current edition approved Ja
12、n. 1, 2011. Published March 2011. DOI:10.1520/F2877-11.2JOM, 53(12), 2001 pp 8-12 and www.nist.gov/public.affairs/releases/wtc-briefing-april0505.htm1Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.1.4 Fire testing is inherently hazar
13、dous. Adequate safe-guards for personnel and property shall be employed inconducting these tests.1.5 The values stated in either SI units or inch-pound unitsare to be regarded separately as standard. The values stated ineach system may not be exact equivalents; therefore, eachsystem shall be used in
14、dependently of the other. Combiningvalues from the two systems may result in non-conformancewith the standard.1.6 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safet
15、y and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:3E176 Terminology of Fire Standards2.2 International Maritime Code: International Code forApplication of Fire Test Procedures, ISBN 92-801-1452-24:A.754 (18) Recom
16、mendation on Fire Resistance Tests for“A,” “B,” and “F” Class Divisions2.3 United States Military Documents:MIL-S-901D Requirements for Shock Tests H.I. (High Im-pact) Shipboard Machinery, Equipment, and Systems5NAVSEAINST 9491.ID Approved Class HI Shock TestingMachines6MIL-STD-3020 Fire Resistance
17、of U.S. Navy SurfaceShips73. Terminology3.1 Refer to Terminology E176 for general terms associatedwith fire issues.3.2 Definitions:3.2.1 A-Class division“A” class divisions in accordancewith Part 3 of IMO FTP Code are those divisions formed bybulkheads and decks which comply with the following crite
18、ria:(a) They are constructed of steel or other equivalent mate-rial;(b) They are suitably stiffened;(c) They are insulated with approved non-combustible ma-terials such that the average temperature of the unexposed sidewill not rise more than 140C above the original temperature,nor will the temperat
19、ure, at any one point, including any joint,rise more than 180C above the original temperature, with thetime listed below:class “A-60” 60 minclass “A-30” 30 minclass “A-15” 15 minclass “A-0” 0 min(d) They are so constructed as to be capable of preventingthe passage of smoke and flame to the end of th
20、e one-hourstandard fire test; and(e) The Administration required a test of a prototype bulk-head or deck in accordance with the Fire Test Procedures Codeto ensure that it meets the above requirements for integrity andtemperature rise.3.2.2 fire resistance, nthe ability of a material, product, orasse
21、mbly to withstand fire or give protection from it for aperiod of time.3.2.2.1 DiscussionFire resistance is the ability of a divi-sion or boundary (typically a bulkhead or overhead) to with-stand fire, give protection from it, prevent fire spread toadjoining compartments, and retain structural integr
22、ity underfire. Structural integrity is the ability to continue to carry astructural load. Fire resistance does not address reaction to fireproperties such as ignitability, surface flame spread, heatrelease rates, smoke density, fire gas toxicity, or other materialfire performance limits.3.2.2.2 fire
23、 resistance ratinga measure of the elapsed timeduring which a material, product, or assembly continues toexhibit fire resistance under specified exposure conditions.3.2.2.3 restricted applicationwhen a division will onlyprotect against a fire threat with the insulation installed on thefire side only
24、, the division is designated as fire resistant withrestricted application.3.2.2.4 un-restricted applicationwhen a division is pro-tected against a fire threat from both sides, the division isdesignated as fire resistant with unrestricted application.3.2.3 non-combustible insulationan insulation mate
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF28772011E1STANDARDTESTMETHODFORSHOCKTESTINGOFSTRUCTURALINSULATIONOFACLASSDIVISIONSCONSTRUCTEDOFSTEELORALUMINUM

链接地址:http://www.mydoc123.com/p-539643.html