1、Designation: F2941 13 An American National StandardStandard Practice forAir Soft Player Safety Briefing1This standard is issued under the fixed designation F2941; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last rev
2、ision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONThis practice is intended to provide air soft game organizers with safety information, which can begiven to each game particip
3、ant prior to the participants first game of the day. The intent is to revisethis practice whenever substantive information becomes available which justifies revising existingrequirements or adding new requirements.1. Scope1.1 This practice is intended to satisfy the demand for basicsafety informatio
4、n, which should be understood by each airsoft game participant prior to the start of the players first gameon the day of play.1.2 The information specifies rules of personal conduct,which might affect the safety of persons who are in closeproximity to an air soft gun.1.3 The information includes pro
5、cedures to be followed byevery person who is in, or near, an area where air soft gamesare being played or air soft ammunition is being shot, and tothe use of safety equipment related to air soft game or air softtarget shooting activities. These procedures are to be followedany time an air soft gun i
6、s being handled.1.4 This standard is intended to be a useful tool for air softgame organizers, but it is not intended to eliminate the need forproper game supervision, conforming to Practice F2940.2. Referenced Documents2.1 ASTM Standards:2F1776 Specification for Eye Protective Devices for Paintball
7、SportsF2679 Specification for 6 mm Projectiles Used with LowEnergy Air GunsF2748 Specification for Low Energy Air Guns (Less Than 1Joule)F2940 Practice for Air Soft Field Operation2.2 ANSI Standards:3ANSI Z87.1 American National Standard for Occupationaland Educational Personal Eye and Face Protecti
8、on De-vices3. Terminology3.1 Definitions of Terms Specific to This Standard:3.1.1 air soft projectile, nprojectile complying with Speci-fication F2679, which is fired from an airsoft gun.3.1.2 air soft gun, ndevice specifically designed to dis-charge air soft projectiles such as but not limited to t
9、hosedescribed in Specification F2748.3.1.3 accidental discharge device, ndevice specificallydesigned to be installed on an airsoft gun to prevent theaccidental discharge of air soft projectiles.3.1.4 ear canal, nasal and oral cavity protection, ndeviceor devices that cover the ear canal, nasal or or
10、al cavities andprevent direct entry of airsoft projectiles into these areas.3.1.5 game area, narea in which airsoft games are con-ducted and in which eye protection suitable for airsoft gameplay is required to be worn.3.1.6 goggles, neye protection device suitable for use inair soft games.3.1.7 gogg
11、les on area, nareas in which all persons arerequired to wear an eye protection device suitable for airsoftgames, such as and not limited to playing fields, game areas,chronograph areas, and target ranges.3.1.8 minimum engagement distance, nminimum distancebetween the shooter and the target at which
12、a shot may be fired.3.1.8.1 DiscussionThis distance is defined based on vari-ous factors in Table 1 of Practice F2940.3.1.9 player, nair soft game participant.1This test method is under the jurisdiction of ASTM Committee F08 on SportsEquipment, Playing Surfaces, and Facilities and is the direct resp
13、onsibility ofSubcommittee F08.27 on Airsoft.Current edition approved July 1, 2013. Published July 2013. DOI: 10.1520/F2941-13.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards volume information,
14、 refer to the standards Document Summary page onthe ASTM website.3Available from American National Standards Institute (ANSI), 25 W. 43rd St.,4th Floor, New York, NY 10036, http:/www.ansi.org.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United S
15、tates13.1.10 playing field, narea delineated by a boundarymarker, in which air soft games are conducted.3.1.11 safe area, narea where the discharge of air softguns is not permitted and actions are taken to prevent acciden-tal discharge of air soft guns.3.1.12 safety mechanism, ndevice that, when act
16、ivated,disables a part of the air soft gun, usually the trigger, to preventunintentional firing in normal use and must be released to allowthe gun to be discharged by the movement of the trigger.3.1.12.1 DiscussionThe device is sometimes referred to asa safety, safety button, or safety lever. An ele
17、ctronic on/offswitch is considered to be a safety mechanism if, when theswitch is placed in the off position, it renders the guninoperable.3.1.13 staging area, narea protected against stray entry ofair soft projectiles, in which air soft players organize them-selves prior to a game.4. Significance a
18、nd Use4.1 Specific safety rules and procedures are important inorder to minimize the risk of injury to persons in the generalarea of air soft guns.5. General Considerations5.1 Persons who participate in air soft games should bemade aware of the hazards associated with the equipment andthe game activ
19、ities.5.2 This standard specifies the minimum requirements for aplayer safety briefing. Air soft game organizers may choose toinclude additional safety instructions in their briefing to play-ers.5.3 Any person permitted into an area requiring goggles beworn must be given the relevant portions of thi
20、s safety briefingbefore being allowed in the area.6. Safety Instructions for Air Soft Game Participants6.1 GogglesAll persons shall be required to wear an eyeprotective device at all times while they are in areas designatedas “goggles on areas.” As no standard exists for air soft eyeprotective devic
21、es at this time all eye protective devices shallbe subject to the approval of the game operator and meets oneof the following:6.1.1 An eye protective device which meets ANSI Z87.1requirements and is manufactured and advertised by themanufacturer as suitable for use in air soft game activity. Thispro
22、tector must have a solid lens material used in the construc-tion rather than a screen or other similar material.6.1.2 Meet Specification F1776.6.2 Goggle Safety:6.2.1 Goggles should be inspected for cracks and to becertain the goggle lens is properly secured by the lens retentionsystem.6.2.2 Goggles
23、 should be checked to be sure they fit snugly.6.2.3 Every person must wear goggles at all times, when heor she is not in a safe area.6.2.4 While in a goggles-on area, a person must never lift orremove his or her goggles for any reason.6.2.5 Any person whose vision is impaired/obscured, shouldhold hi
24、s or her goggles securely in place and call out forassistance from a referee, safety official, or teammate to helpget off the field safely.6.2.6 In the event a persons goggles are knocked off,damaged, or displaced, that person should set their gun down,drop to the ground, cover their eyes, and call
25、out that theirgoggles have fallen off and to stop shooting. Everyone whohears this should immediately stop shooting, put their gundown, and stop playing, until a referee has arrived, the playerwith the goggle problem has been taken off the field, and thereferee announces that the game can resume.6.2
26、.7 Just because a person is eliminated from a game doesNOT mean that person can remove his or her goggles. Gogglesmust not be removed until the person wearing them is in adesignated safe area. Goggles must always stay on, until anaccidental discharge device is securely in place.6.3 All persons shall
27、 be required to wear adequate protec-tion to limit entry of airsoft pellets into the ear canal.6.4 It is recommended that all persons wear additionalprotective device(s) which limit the entry of airsoft projectilesinto the nasal and oral cavity.6.5 Accidental Discharge DeviceAn accidental discharged
28、evice must be securely in place any time you are not in ashooting zone or on a playing field, and at any time when areferee or other official has ordered barrel blocking devices tobe used.6.6 Every airsoft guns velocity must be checked before thefirst time it goes onto the playing field, and should
29、be checkedagain as needed throughout the playing day.6.6.1 The velocity at which an airsoft gun is shooting mustbe measured by use of a chronograph as defined in subsection4.7 of Practice F2940.6.6.2 Airsoft gun velocities must conform to Table 1 inPractice F2940.6.6.3 Players will be advised of the
30、 minimum engagementdistance for each gun they use in play.6.6.4 A referee or other game official may require a velocitycheck of any airsoft gun at any time for any reason.6.7 Every airsoft game participant renting equipment mustreceive instructions on, or demonstrate an understanding of,how the rent
31、al equipment works and how to use it properly.This lesson must include but is not limited to the following:6.7.1 How to load and unload the airsoft gun,6.7.2 How to use each safety device on the airsoft gun,whether mechanical or electronic,6.7.3 How to use the accidental discharge device on theairso
32、ft gun,6.7.4 How to properly put on and adjust the goggle system.6.8 Emergency ProceduresParticipates shall be informedof what to do in case of an emergency.7. Keywords7.1 airsoft; airsoft game; safety; safety briefingF2941 132ASTM International takes no position respecting the validity of any paten
33、t rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof infringement of such rights, are entirely their own responsibility.This standard is subject to revision a
34、t any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standardsand should be addressed to ASTM International Headquarters. Your commen
35、ts will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted
36、by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F2941 133
