ASTM F2951-2012 Standard Consumer Safety Specification for Baby Monitors《婴儿监视器的标准消费者安全规范》.pdf
《ASTM F2951-2012 Standard Consumer Safety Specification for Baby Monitors《婴儿监视器的标准消费者安全规范》.pdf》由会员分享,可在线阅读,更多相关《ASTM F2951-2012 Standard Consumer Safety Specification for Baby Monitors《婴儿监视器的标准消费者安全规范》.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、Designation: F2951 12Standard Consumer Safety Specification forBaby Monitors1This standard is issued under the fixed designation F2951; the number immediately following the designation indicates the year oforiginal adoption or, in the case of revision, the year of last revision. A number in parenthe
2、ses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.INTRODUCTIONThis consumer safety specification addresses incidents associated with corded baby monitors thatwere identified by the U.S. Consumer Product Safety Commi
3、ssion (CPSC).Incidents identified by the CPSC and addressed in this consumer safety specification includestrangulations as a result of entanglement in cords.This consumer safety specification is not intended to address corded monitors that are eitherblatantly misused or abused. This consumer safety
4、specification is written within current state-of-the-art technology and is intended to be updated if substantive information becomes available thatnecessitates additional requirements or justifies revision of existing requirements.1. Scope1.1 This consumer safety specification establishes require-me
5、nts for corded baby monitors, including audio monitors,video monitors, and motion sensor monitors. It also providesrequirements for labeling, instructional material and packag-ing.1.1.1 This consumer safety specification is intended tominimize injuries to children resulting from normal usage andreas
6、onably foreseeable misuse or abuse of baby monitors.1.2 No product produced after the approval date of thisconsumer safety specification shall, either by label or othermeans, indicate compliance with this specification unless itconforms to all applicable requirements contained herein,before and afte
7、r all testing.1.3 UnitsThe values stated in inch-pound units are to beregarded as standard. The values given in parentheses aremathematical conversions to SI units that are provided forinformation only and are not considered standard.1.4 This standard does not purport to address all of thesafety con
8、cerns, if any, associated with its use. It is theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2D3359 Test Methods for Measuring Adhes
9、ion by Tape TestF963 Consumer Safety Specification for Toy Safety2.2 Federal Standards:316 CFR 1303 Ban of Lead-Containing Paint and CertainConsumer Products Bearing Lead-Containing Paint16 CFR 1500 Hazardous Substances Act Regulations in-cluding sections: 1500.3 (c) (6) (vi) Definition of “Flam-mab
10、le Solid”1500.48 Technical Requirements for Determining a SharpPoint In Toys and Other Articles Intended for Use ByChildren Under Eight Years of Age1500.49 Technical Requirements for Determining a SharpMetal or Glass Edge in Toys or OtherArticles Intended forUse by Children Under Eight Years of Age1
11、500.53 Test Methods for Simulating Use and Abuse ofToys and Other Articles Intended for Use by ChildrenOver 36 but Not Over 96 Months of Age3. Terminology3.1 Definitions of Terms Specific to This Standard:1This specification is under the jurisdiction of ASTM Committee F15 onConsumer Products and is
12、the direct responsibility of Subcommittee F15.68 onBaby Monitors.Current edition approved May 1, 2012. Published May 2012. DOI: 10.1520/F2951-12.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book of ASTMStandards
13、volume information, refer to the standards Document Summary page onthe ASTM website.3Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401, http:/www.access.gpo.gov.1Copyright ASTM International, 100 Barr Harbor Drive,
14、 PO Box C700, West Conshohocken, PA 19428-2959, United States.3.1.1 conspicuous, adjdescribes a label that is visiblewhen the unit is in a manufacturers recommended use positionto a person standing near the unit at any one position aroundthe unit but not necessarily visible from all positions.3.1.2
15、cord, nalternating current (A/C) adapter and othersimilar cords including lengths of slender flexible materialincluding monofilaments, rope, woven and twisted cord, plasticand textile tapes, ribbon, and those materials commonly calledstring.3.1.3 corded monitor, nmonitor that uses a cord or onethat
16、has an option to use a cord.3.1.4 manufacturers recommended use position, nanyposition that is presented by the manufacturer in any descrip-tive or instructional literature as a normal, allowable, oracceptable configuration for use of the product. This specifi-cally excludes positions that the manuf
17、acturer shows in a likemanner in its literature to be unacceptable, unsafe, or notrecommended.3.1.5 nonpaper label, nany label material (such as plasticor metal) that either will not tear without the aid of tools ortears leaving a sharply defined edge or labels made from fabric.3.1.6 occupant retent
18、ion area, nany area designated bythe manufacturer as being the recommended area for theoccupant of the product.3.1.7 paper label, nany label material that tears withoutthe aid of tools and leaves a fibrous edge.3.1.8 protective covering, nrigid shielding, rigid encase-ment, or other means of enclosi
19、ng a cord.4. Calibration and Standardization4.1 The unit shall be completely assembled, unless other-wise noted, in accordance with the manufacturers instructions.4.2 The product to be tested shall be preconditioned in aroom with an ambient temperature of 73 6 9F (23 6 5C) forat least 1 h before tes
20、ting. Testing shall then be conductedwithin this temperature range.4.3 All testing required by this specification shall be con-ducted on the same unit.5. General Requirements5.1 There shall be no hazardous sharp points or edges asdefined by 16 CFR 1500.48 and 16 CFR 1500.49 before orafter testing to
21、 this consumer safety specification.5.2 Corded monitors shall provide warnings to instructconsumers not to place a baby monitor cord where it isaccessible to a child, or, if intended to be attached to a crib orused within 3 ft (0.9 m) of a crib, shall have cords that areencased in a rigid protective
22、 covering to prevent access to acord that could cause a strangulation hazard.5.2.1 Corded monitors not intended to be attached to a cribshall have warning labels as defined in 7.2.5.2.2 Corded monitors intended to be attached to a crib orused within 3 ft (0.9 m) of a crib shall have cords that arein
23、accessible to the occupant by rigid encasement, shielding, orother means. When installed according to the manufacturersinstructions, cords shall remain inaccessible when tested to 6.1.Cords are considered accessible if, after performing these tests,any portion of the cord is exposed within 36 in. (9
24、1 cm) to theoccupant retention area and can be contacted by any portionforward of the collar of the accessibility probe as described in16 CFR 1500.48 and 16 CFR 1500.49. EXCEPTION: For unitsthat are secured to a crib and the shield/enclosure extendsdownward to the floor, the cord is considered acces
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
最后一页预览完了!喜欢就下载吧,查找使用更方便
5000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- ASTMF29512012STANDARDCONSUMERSAFETYSPECIFICATIONFORBABYMONITORS 婴儿 监视器 标准 消费者 安全 规范 PDF

链接地址:http://www.mydoc123.com/p-539801.html