ASTM F3059-2015 Standard Specification for Fiber-Reinforced Polymer (FRP) Gratings Used in Marine Construction and Shipbuilding《海洋工程和船舶用纤维增强型聚合物 (FRP) 隔栅的标准规格》.pdf

上传人:sumcourage256 文档编号:539966 上传时间:2018-12-07 格式:PDF 页数:24 大小:1.36MB
下载 相关 举报
ASTM F3059-2015 Standard Specification for Fiber-Reinforced Polymer (FRP) Gratings Used in Marine Construction and Shipbuilding《海洋工程和船舶用纤维增强型聚合物 (FRP) 隔栅的标准规格》.pdf_第1页
第1页 / 共24页
ASTM F3059-2015 Standard Specification for Fiber-Reinforced Polymer (FRP) Gratings Used in Marine Construction and Shipbuilding《海洋工程和船舶用纤维增强型聚合物 (FRP) 隔栅的标准规格》.pdf_第2页
第2页 / 共24页
ASTM F3059-2015 Standard Specification for Fiber-Reinforced Polymer (FRP) Gratings Used in Marine Construction and Shipbuilding《海洋工程和船舶用纤维增强型聚合物 (FRP) 隔栅的标准规格》.pdf_第3页
第3页 / 共24页
ASTM F3059-2015 Standard Specification for Fiber-Reinforced Polymer (FRP) Gratings Used in Marine Construction and Shipbuilding《海洋工程和船舶用纤维增强型聚合物 (FRP) 隔栅的标准规格》.pdf_第4页
第4页 / 共24页
ASTM F3059-2015 Standard Specification for Fiber-Reinforced Polymer (FRP) Gratings Used in Marine Construction and Shipbuilding《海洋工程和船舶用纤维增强型聚合物 (FRP) 隔栅的标准规格》.pdf_第5页
第5页 / 共24页
亲,该文档总共24页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、Designation: F3059 15 An American National StandardStandard Specification forFiber-Reinforced Polymer (FRP) Gratings Used in MarineConstruction and Shipbuilding1This standard is issued under the fixed designation F3059; the number immediately following the designation indicates the year oforiginal a

2、doption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification provides the testing and performancerequirements f

3、or fiber-reinforced polymer (FRP) gratings usedin marine construction and shipbuilding as an equivalency tothe specification of steel gratings rated for a maximum load of94 lbf/ft2(4.5 kN/m2).1.2 The purpose of this specification is to ensure that allFRP gratings are designed and tested appropriatel

4、y to ensurepersonnel safety. It does not address the ability of the gratingsto support either moving or stationary equipment during orafter a fire exposure.1.3 This specification addresses fire conditions based onTest Methods E119 fire exposure and does not address hydro-carbon pool or jet fire expo

5、sures.1.4 This specification is intended for use by all personsdesigning, manufacturing, testing, inspecting, and maintainingFRP gratings.1.5 UnitsThe values stated in inch-pound units are to beregarded as the standard. The values given in parentheses aremathematical conversions to SI units that are

6、 provided forinformation only and are not considered standard.1.6 This specification does not constitute regulations or shipclassification rules, which shall be consulted where applicable.1.7 This standard does not purport to address all of thesafety concerns, if any, associated with its use. It is

7、theresponsibility of the user of this standard to establish appro-priate safety and health practices and determine the applica-bility of regulatory limitations prior to use.2. Referenced Documents2.1 ASTM Standards:2B117 Practice for Operating Salt Spray (Fog) ApparatusD2047 Test Method for Static C

8、oefficient of Friction ofPolish-Coated Flooring Surfaces as Measured by theJames MachineD4060 Test Method for Abrasion Resistance of OrganicCoatings by the Taber AbraserD4329 Practice for Fluorescent Ultraviolet (UV) Lamp Ap-paratus Exposure of PlasticsE84 Test Method for Surface Burning Characteris

9、tics ofBuilding MaterialsE119 Test Methods for Fire Tests of Building Constructionand MaterialsE695 Test Method of Measuring Relative Resistance ofWall, Floor, and Roof Construction to Impact Loading2.2 Other Standards:46 CFR 159 ShippingApproval of Equipment and Mate-rials3NVIC 02-06 Follow-Up Prog

10、rams for Fire-Safety Type-Approved Products4NVIC 9-97 Change 1Guide to Structural Fire Protection53. Terminology3.1 Definitions:3.1.1 compression molding, vmanufacturing process in-volving match die molds that compress the fiber reinforcedmatrix, generally under pressure and heat, to produce thefini

11、shed product.3.1.2 fiber-reinforced polymer, FRP, ncomposite materialmade of a resin matrix reinforced with fibers.3.1.2.1 DiscussionThe fibers are usually made of glass orcarbon fiber, while the polymer is usually an epoxy, vinyl ester,or polyester thermosetting plastic. The term “polymer” issometi

12、mes replaced by “plastic.”3.1.3 fire integrity, nability of a structure to retain func-tionality after a fire.1This specification is under the jurisdiction of ASTM Committee F25 on Shipsand Marine Technology and is the direct responsibility of Subcommittee F25.03 onOutfitting and Deck Machinery.Curr

13、ent edition approved Nov. 15, 2015. Published December 2015. Originallyapproved in 2014. Last previous edition approved in 2014 as F3059 14. DOI:10.1520/F3059-15.2For referenced ASTM standards, visit the ASTM website, www.astm.org, orcontact ASTM Customer Service at serviceastm.org. For Annual Book

14、of ASTMStandards volume information, refer to the standards Document Summary page onthe ASTM website.3Available from U.S. Government Printing Office Superintendent of Documents,732 N. Capitol St., NW, Mail Stop: SDE, Washington, DC 20401, http:/www.access.gpo.gov.4Available from United States Coast

15、Guard (USCG), U.S. Coast GuardHeadquarters, 2703 Martin Luther King Jr. Ave. SE Stop 7509, Washington, DC,20593-7509, http:/www.uscg.mil/hq/cg5/cg5214/docs/NVIC02-06.pdf.5Available from United States Coast Guard (USCG), U.S. Coast GuardHeadquarters, 2703 Martin Luther King Jr. Ave. SE Stop 7509, Was

16、hington, DC,20593-7509, http:/www.uscg.mil/hq/cg5/nvic/pdf/1997/n9-97ch1.pdf.Copyright ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959. United States13.1.3.1 DiscussionFire integrity levels for FRP gratingsare described as (from lowest to highest) Level 3, Le

17、vel 2, andLevel 1. Level 0 gratings are not qualified for fire integrity.3.1.4 glass-reinforced polymer, GRP, nfiber-reinforcedpolymer made of a resin matrix reinforced by glass fibers.3.1.5 molded grating, nFRP grating produced by the openmold process in which dry glass fiber and thermoset resin is

18、placed in the mold in both directions.3.1.5.1 DiscussionAfter filling the mold with the desig-nated amount of material, the resin is allowed to cure in theopen mold. Square mesh molded grating has nearly equalstrength and stiffness in longitudinal and transverse directions.Molded grating is usually

19、manufactured in square mesh orrectangular mesh configurations. See Fig. 1 and Fig. 2.3.1.6 open molding, vmanual process involving the com-bination of liquid resin and fiber reinforcements in an openmold to produce a finished part resembling the inverse of themold.3.1.6.1 DiscussionLiquid resin and

20、continuous fibers aresystematically laid in a moldlayer upon layer manually to adesired thickness and panel dimension.3.1.7 pultruded grating, ngrating produced from an as-sembly of pultruded structural shapes assembled into a gridpattern.3.1.7.1 DiscussionPultruded FRP grating products areassembled

21、 from bearing bars and cross rods manufactured fromthe pultrusion process as shown in Fig. 3. Pultruded grating hasmore strength and stiffness in the direction of the bearing bars.3.1.8 pultrusion, nmanufacturing process to form continu-ous lengths of reinforced polymer structural shapes.3.1.9 quali

22、fied span, nFRP grating span used duringpreload and post load fire tests minimum 44 in. (112 cm).3.1.10 surface flame spread, npropagation of a flameaway from the source of ignition across the surface of thespecimen.3.2 Definitions of Terms Specific to This Standard:3.2.1 shall, vin this specificati

23、on, indicates a mandatoryrequirement.3.2.2 should, nin this specification, indicates a recom-mended requirement.3.3 Abbreviations:3.3.1 AFFFAqueous film-forming foam3.3.2 AHJAuthority having jurisdiction3.3.3 ASTMAmerican Society for Testing and Materials3.3.4 L1Level 1 fire integrity grating3.3.5 L

24、2Level 2 fire integrity grating3.3.6 L3Level 3 fire integrity grating3.3.7 L0Flame spread only3.3.8 MODUMobile offshore drilling unit3.3.9 NVICNavigation and Vessel Inspection Circular3.3.10 USCGU.S. Coast Guard3.3.11 UVUltraviolet4. Significance and Use4.1 This specification is for FRP gratings use

25、d in machineryspaces, cargo areas, and on-deck areas but not withinaccommodation, service, control spaces, and areas wheresmoke and toxicity is a concern. The test requirements andcriteria for FRP gratings have been developed based on theexpected environmental conditions, intended use, and firehazar

26、d the gratings could be exposed to in conjunction withrequirements for means of escape and fire brigade access to thearea where the FRP gratings will be located. The structural fireintegrity test requirements have been developed based oncomparative testing with steel gratings rated for maximum loado

27、f 94 lbf/ft2(4.5 kN/m2). The structural fire integrity require-ments for the specific locations are summarized in Table 1. Thefire test requirements include surface flammability testing andstructural fire integrity testing with three levels of structural fireintegrity that may be achieved as follows

28、:FIG. 1 Square Mesh Molded GratingF3059 1524.1.1 Level 1 (L1)FRP gratings meeting the L1 perfor-mance criteria provide the highest degree of safety and areintended for use in escape routes or areas in which access forfirefighting, emergency operation, or rescue is needed after asignificant fire expo

29、sure that may weaken the gratings. Level 1gratings may also be used in any areas requiring Levels 2 or 3gratings.4.1.2 Level 2 (L2)FRP gratings meeting the L2 perfor-mance criteria are intended for use in areas in which personnelmay need to assemble after the grating has been exposed to afire and ar

30、e tested to ensure that they will be able to sustain apost-fire structural loading. Areas in which L2 gratings arespecified include temporary safe refuge or lifeboat embarkationstations. Level 2 gratings may also be used in any areasrequiring Level 3 gratings.4.1.3 Level 3 (L3)FRP gratings meeting t

31、he L3 perfor-mance criteria are intended for use in areas used as egressroutes or that may require access for firefighting, emergencyoperations, or rescue during or shortly after exposure to a verylimited fire not likely involving flammable liquids.4.1.4 Level 0 (L0)FRP gratings tested to Test Metho

32、d E84with a flame spread index 20 and a smoke developed index of450. L0 FRP gratings have no level of fire integrity. L0gratings are used for personnel walkways, catwalks, ladders,platforms, or access areas in cargo holds and tanks.FIG. 2 Rectangular Mesh Molded GratingFIG. 3 Pultruded GratingF3059

33、1534.2 These test methods in this specification do not providethe following:4.2.1 Full information as to the performance of the FRPgrating with materials, construction, dimensions, coatings, andso forth, other than tested.4.3 In these test methods, the test specimens are subjected toone or more spec

34、ific tests under laboratory conditions. Whendifferent test conditions are substituted or the end-use condi-tions are changed, it is not always possible by, or from, thesetest methods to predict changes to the characteristics measured.Therefore, the results of these laboratory tests are valid only fo

35、rthe test conditions described in these test methods.4.4 The fire-resistance test methods specified herein requiretest specimens to be exposed to a standard fire that is controlledto achieve specified temperatures throughout a specified timeperiod or heat exposure. These are followed by the applicat

36、ionof specified loads. These test methods provide a relativemeasure of performance under the specified test conditions.The fire exposure is not representative of all fire conditions.Variation from the test conditions or test specimenconstruction, such as size, materials, method of assembly, andso fo

37、rth, may affect the fire-test response. For these reasons,evaluation of such variations may be required for application toconstruction in the field. However, variations in the requiredtest exposure conditions are considered outside the scope ofthis specification.5. Sampling5.1 Sampling methods shall

38、 be as required to providereasonable assurance that the test samples are truly represen-tative of the standard manufactured product. When required,test specimens of products shall be sampled at the manufac-turing facility by personnel representing an accredited testinglaboratory, accredited inspecti

39、on agency, or accredited certifi-cation agency. Sampling at a warehouse or distribution centerin lieu of sampling at the manufacturing facility is permittedprovided the testing laboratory, inspection agency, or certifi-cation agency samples the materials and correlates the sampledmaterials with the

40、finished product specification. The testspecimens shall be representative of the FRP gratings to bequalified including materials, construction, profile, dimensions,coatings, and so forth.6. Number of Tests and Retests6.1 GeneralThe number of tests are as described in thetest requirements portion of

41、this specification. If significantchanges occur to the manufacturing process or material speci-fications that may affect the physical properties or systemqualification requirements, qualification tests related to thesignificant change shall be required.TEST REQUIREMENTS7. Summary7.1 The following te

42、st requirements shall be met: deflectionlimits, assembled grating ultimate failure, wheel loading,assembled panel impact resistance, skid resistance, durability,ultraviolet (UV) resistance, salt spray, surface flammability,and structural fire integrity. Testing shall be conducted by alaboratory acce

43、ptable to the AHJ.TABLE 1 Structural Fire Integrity RequirementsLocation ServiceStructuralFireIntegrityMachineryspacesWalkways or areas which may be usedfor escape, or access for firefighting,emergency operation, or rescueL1APersonnel walkways, catwalks, ladders,platforms, or access areas other than

44、those described aboveL3Cargo pumproomsAll personnel walkways, catwalks,ladders, platforms, or access areasL1Cargo holds Walkways or areas which may be usedfor escape, or access for firefighting,emergency operation, or rescueL1Personnel walkways, catwalks, ladders,platforms, or access areas other tha

45、nthose described aboveL0Cargo tanks All personnel walkways, catwalks,ladders, platforms, or access areasL0Fuel oil tanks All personnel walkways, catwalks,ladders, platforms, or access areasL0Ballast watertanksAll personnel walkways, catwalks,ladders, platforms, or access areasL0Cofferdams, voidspace

46、s, doublebottoms, pipetunnels, and soforthAll personnel walkways, catwalks,ladders, platforms, or access areasL0Accommodation,service, andcontrol spacesAll personnel walkways, catwalks,ladders, platforms, or access areas Not permittedLifeboatembarkation ortemporary saferefuge stationsin open deckare

47、asAll personnel walkways, catwalks,ladders, platforms, or access areasL2Open decks orsemi-enclosedareasOperational areas and access routes fordeck foam firefighting systems on tankvesselsL2Walkways or areas that may be used forescape, or access for firefighting systemsand AFFF hose reels, emergencyo

48、peration, or rescue on MODUs andproduction platforms including safeaccess to tanker bowsL2Walkways or areas that may be used forescape or access for firefighting systems,emergency operation, or rescue otherthan those described aboveL3Personnel walkways, catwalks, ladders,platforms, or access areas o

49、ther thanthose described aboveL3AIf the machinery space does not contain any internal combustion machinery,other oil burning, oil heating, or oil pumping units, fuel oil filling stations, or otherpotential hydrocarbon fire sources and has not more than 5.5 lb/ft2(2.5 kg/m2)ofcombustible storage, gratings of L3 structural fire integrity may be used in lieu ofL1.F3059 1548. Deflection Limits (Application, Not Fire)8.1 The grating panel shall meet the following load deflec-tion limits:8.1.1 The specified performance requirements for each

展开阅读全文
相关资源
猜你喜欢
相关搜索

当前位置:首页 > 标准规范 > 国际标准 > ASTM

copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
备案/许可证编号:苏ICP备17064731号-1