AWS D10 12M D10 12-2000 Guide for Welding Mild Steel Pipe《焊接低碳钢管指南》.pdf
《AWS D10 12M D10 12-2000 Guide for Welding Mild Steel Pipe《焊接低碳钢管指南》.pdf》由会员分享,可在线阅读,更多相关《AWS D10 12M D10 12-2000 Guide for Welding Mild Steel Pipe《焊接低碳钢管指南》.pdf(49页珍藏版)》请在麦多课文档分享上搜索。
1、Guide for WeldingMild Steel PipeAWS D10.12M/D10.12:2000An American National Standard550 N.W. LeJeune Road, Miami, Florida 33126AWS D10.12M/D10.12:2000An American National StandardApproved byAmerican National Standards InstituteJuly 20, 2000Guide for WeldingMild Steel PipeSupersedes ANSI/AWS D10.12-8
2、9Prepared byAWS D10 Committee on Piping and TubingUnder the Direction ofAWS Technical Activities CommitteeApproved byAWS Board of DirectorsAbstractThis document presents recommended practices for welding mild steel pipe. It is intended to cover piping systems suchas for low pressure heating, air con
3、ditioning, refrigeration, water supplies, as well as some gas or chemical systems. Itprovides welding techniques for oxyacetylene, shielded metal arc, gas tungsten arc, gas metal arc, and flux cored arcwelding. This document does not address the needs of pipe steels or service conditions which may r
4、equire Post WeldHeat Treatment (PWHT).Key WordsMild steel pipe, tubing, shielded metal arc welding, oxyacetylene welding, gas tungsten arc welding, gas metal arc welding, flux cored arc weldingStatement on Use of AWS American National StandardsAll standards (codes, specifications, recommended practi
5、ces, methods, classifications, and guides) of the AmericanWelding Society are voluntary consensus standards that have been developed in accordance with the rules of the AmericanNational Standards Institute. When AWS standards are either incorporated in, or made part of, documents that areincluded in
6、 federal or state laws and regulations, or the regulations of other governmental bodies, their provisions carrythe full legal authority of the statute. In such cases, any changes in those AWS standards must be approved by thegovernmental body having statutory jurisdiction before they can become a pa
7、rt of those laws and regulations. In allcases, these standards carry the full legal authority of the contract or other document that invokes the AWS standards.Where this contractual relationship exists, changes in or deviations from requirements of an AWS standard must be byagreement between the con
8、tracting parties.International Standard Book Number: 0-87171-551-1American Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126 2000 by American Welding Society. All rights reservedPrinted in the United States of AmericaAWS American National Standards are developed through a consensus standards d
9、evelopment process that bringstogether volunteers representing varied viewpoints and interests to achieve consensus. While AWS administers the processand establishes rules to promote fairness in the development of consensus, it does not independently test, evaluate, orverify the accuracy of any info
10、rmation or the soundness of any judgments contained in its standards.AWS disclaims liability for any injury to persons or to property, or other damages of any nature whatsoever, whether spe-cial, indirect, consequential or compensatory, directly or indirectly resulting from the publication, use of,
11、or reliance on thisstandard. AWS also makes no guaranty or warranty as to the accuracy or completeness of any information published herein.In issuing and making this standard available, AWS is not undertaking to render professional or other services for or onbehalf of any person or entity. Nor is AW
12、S undertaking to perform any duty owed by any person or entity to someoneelse. Anyone using these documents should rely on his or her own independent judgment or, as appropriate, seek the adviceof a competent professional in determining the exercise of reasonable care in any given circumstances.This
13、 standard may be superseded by the issuance of new editions. Users should ensure that they have the latest edition.Publication of this standard does not authorize infringement of any patent. AWS disclaims liability for the infringementof any patent resulting from the use or reliance on this standard
14、.Finally, AWS does not monitor, police, or enforce compliance with this standard, nor does it have the power to do so.Official interpretations of any of the technical requirements of this standard may be obtained by sending a request, in writ-ing, to the Managing Director Technical Services, America
15、n Welding Society, 550 N.W. LeJeune Road, Miami, FL 33126(see Annex E). With regard to technical inquiries made concerning AWS standards, oral opinions on AWS standards maybe rendered. However, such opinions represent only the personal opinions of the particular individuals giving them. Theseindivid
16、uals do not speak on behalf of AWS, nor do these oral opinions constitute official or unofficial opinions or interpre-tations of AWS. In addition, oral opinions are informal and should not be used as a substitute for an official interpretation.This standard is subject to revision at any time by the
17、AWS D10 Committee on Piping and Tubing. It must be reviewedevery five years and if not revised, it must be either reapproved or withdrawn. Comments (recommendations, additions, ordeletions) and any pertinent data that may be of use in improving this standard are required and should be addressed toAW
18、S Headquarters. Such comments will receive careful consideration by the AWS D10 Committee on Piping and Tub-ing and the author of the comments will be informed of the Committees response to the comments. Guests are invited toattend all meetings of the AWS D10 Committee on Piping and Tubing to expres
19、s their comments verbally. Procedures forappeal of an adverse decision concerning all such comments are provided in the Rules of Operation of the TechnicalActivities Committee. A copy of these Rules can be obtained from the American Welding Society, 550 N.W. LeJeuneRoad, Miami, FL 33126.Photocopy Ri
20、ghtsAuthorization to photocopy items for internal, personal, or educational classroom use only, or the internal, personal, oreducational classroom use only of specific clients, is granted by the American Welding Society (AWS) provided that theappropriate fee is paid to the Copyright Clearance Center
21、, 222 Rosewood Drive, Danvers, MA 01923, Tel: 978-750-8400;online: http:/.iiiPersonnelAWS D10 Committee on Piping and TubingW. J. Sperko, Chair Sperko Engineering ServicesM. C. Shepard, 1st Vice Chair Raytheon Engineers and ConstructorsD. J. Connell, 2nd Vice Chair Detroit EdisonT. R. Potter, Secret
22、ary American Welding SocietyF. G. Armao The Lincoln Electric CompanyR. E. Avery Avery Consulting Associates, IncorporatedW. L. Ballis ConsultantC. J. Bishop Medical Gas Management, IncorporatedC. R. Brashears Alyeska Pipeline Service CompanyK. Brazzell Liburdi Dimetrics CorporationH. W. Ebert Exxon
23、Research and Engineering CompanyW. R. Etie W. R. Etie ConsultantsA. L. Farland Brookhaven National LaboratoryS. Findlan Electric Power Research InstituteG. Frederick Electric Power Research Institute*E. A. Harwart ConsultantG. K. Hickox ConsultantJ. Hill Philip Technical Services(formerly Hill Techn
24、ical Services, Incorporated)J. E. Hinkel Consultant, Lincoln Electric Company*R. B. Kadiyala Techalloy CompanyM. P. Lang United Association Local 501B. B. MacDonald United AssociationL.A. Maier, Jr. ConsultantJ. W. McEnerney Gibson TubeP. A . M i ch a l s k i East Ohio Gas*J. W. Moeller ConsultantW.
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
本资源只提供5页预览,全部文档请下载后查看!喜欢就下载吧,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- AWSD1012MD10122000GUIDEFORWELDINGMILDSTEELPIPE 焊接 低碳钢 指南 PDF

链接地址:http://www.mydoc123.com/p-541929.html