BS 4479-2-1990 Design of articles that are to be coated - Recommendations for electroplated and autocatalytic coatings《层覆物品设计 第2部分 电镀和自动催化覆层推荐标准》.pdf

上传人:unhappyhay135 文档编号:544429 上传时间:2018-12-09 格式:PDF 页数:16 大小:501.22KB
下载 相关 举报
BS 4479-2-1990 Design of articles that are to be coated - Recommendations for electroplated and autocatalytic coatings《层覆物品设计 第2部分 电镀和自动催化覆层推荐标准》.pdf_第1页
第1页 / 共16页
BS 4479-2-1990 Design of articles that are to be coated - Recommendations for electroplated and autocatalytic coatings《层覆物品设计 第2部分 电镀和自动催化覆层推荐标准》.pdf_第2页
第2页 / 共16页
BS 4479-2-1990 Design of articles that are to be coated - Recommendations for electroplated and autocatalytic coatings《层覆物品设计 第2部分 电镀和自动催化覆层推荐标准》.pdf_第3页
第3页 / 共16页
BS 4479-2-1990 Design of articles that are to be coated - Recommendations for electroplated and autocatalytic coatings《层覆物品设计 第2部分 电镀和自动催化覆层推荐标准》.pdf_第4页
第4页 / 共16页
BS 4479-2-1990 Design of articles that are to be coated - Recommendations for electroplated and autocatalytic coatings《层覆物品设计 第2部分 电镀和自动催化覆层推荐标准》.pdf_第5页
第5页 / 共16页
亲,该文档总共16页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、BRITISH STANDARD BS4479-2: 1990 Design of articles that are to be coated Part 2: Recommendations for electroplated and autocatalytic coatings UDC672/673:62/.795:006:669.857BS4479-2:1990 This British Standard, having been prepared under the direction of the Surface Coatings (other than Paints) Standa

2、rds Policy Committee, was published under the authority of the Board of BSI and comes into effect on 31July 1990 BSI03-1999 First published, as BS4479, August1969 First revision, as BS4479-2July1990 The following BSI references relate to the work on this standard: Committee reference SRC/10 Draft fo

3、r comment86/53497DC ISBN0580179001 Committees responsible for this British Standard The preparation of this British Standard was entrusted by the Surface Coatings (other than Paints) Standards Policy Committee (SRC/-) to Technical Committee SRC/10, upon which the following bodies were represented: B

4、ritish Anodising Association Institute of Metal Finishing Institute of Sheet Metal Engineering Institute of Vitreous Enamellers International Tin Research Institute Metal Finishing Association Welding Institute Zinc Development Association Amendments issued since publication Amd. No. Date CommentsBS

5、4479-2:1990 BSI 03-1999 i Contents Page Committees responsible Inside front cover Foreword ii 1 Scope 1 2 Definitions 1 3 Design considerations for electroplated articles 1 4 Design considerations for autocatalytically plated articles 3 Appendix A Diagrams illustrating preferred and deprecated desig

6、n features for articles to be electroplated 4 Figure 1 Rolled edges 4 Figure 2 Hollow articles 4 Figure 3 Corners 4 Figure 4 Edges 4 Figure 5 Fins 5 Figure 6 Indentations 5 Figure 7 Protruberances 5 Figure 8 Ribs 5 Figure 9 Slots 6 Figure 10 Bends 6 Figure 11 Blind holes 6 Figure 12 Holes 6 Figure 1

7、3 Overlap joints 7 Figure 14 Welded joints 7 Figure 15 Screwed joints 7 Figure 16 Flat plates 8 Figure 17 Selective plating features 8 Figure 18 Stacking densities 9 Publications referred to Inside back coverBS4479-2:1990 ii BSI 03-1999 Foreword This Part of BS4479 has been prepared under the direct

8、ion of the Surface Coatings (other than Paints) Standards Policy Committee and is based on a draft prepared by the Institute of Metal Finishing. The BSI Technical Committee acknowledges the contribution to this revision by the Institute 1)and by the Committee for the Promotion of Electroplating. Thi

9、s Part of BS4479 is one of a series of Parts which together form a revision of BS4479:1969. On publication of all the Parts, BS4479:1969 will be withdrawn. This revision of BS4479 comprises the following Parts: Part 1: General recommendations; Part 2: Recommendations for electroplated and autocataly

10、tic coatings; Part 3: Recommendations for conversion coatings; Part 4: Recommendations for paint coatings and varnish coatings; Part 5: Recommendations for anodic oxidation coatings; Part 6: Recommendations for hot-dip metal coatings; Part 7: Recommendations for thermally sprayed coatings; Part 8: R

11、ecommendations for vitreous enamel coatings; Part 9: Recommendations for low pressure and vacuum deposited coatings. BS4479 is directed towards helping to maximize the benefit obtained from coating processes. There is a wide variety of coating processes, developed and established industrially, inten

12、ded to enhance or transform the surfaces of manufactured articles. However, time and money are often wasted because the design of many articles is unsuitable for the coating process to be applied. Coating is only one part of the manufacturing process and should not be ignored, or viewed in isolation

13、, when considering the overall costs and quality. This revision of BS4479 has been undertaken to extend the range of coating processes covered. It is not intended to cover every conceivable design detail, type of article or service condition. Adherence to the general principles described will, howev

14、er, greatly assist in the achievement of the desired results. In any case of doubt or difficulty, specialist advice in the particular type of process being considered should be sought. This Part of BS4479 is not a specification and should not be used as such. The recommendations are intended to prov

15、ide guidance towards good practice. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summa

16、ry of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 to10, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on theinside front

17、 cover. 1) Institute of Metal Finishing.BS4479-2:1990 BSI 03-1999 1 1 Scope This Part of BS4479 gives recommendations for the design of parts that are to be coated by electroplating or autocatalytic plating. This Part of BS4479 applies to the various techniques available for vat and barrel electropl

18、ating, selective electroplating, autocatalytic plating (commonly referred to as electroless plating, though this term is deprecated), but does not give full details of the various processes available for the plating of either metallic or non-metallic surfaces. NOTE 1Many of the basic design recommen

19、dations given are equally applicable to both metallic articles and to those manufactured from other materials, e.g.plastics. NOTE 2It is recommended that Part1 of BS4479 be read in conjunction with this Part. Part1 includes a list of British Standards relating to processes covered by BS4479 but not

20、necessarily referred to in each Part. NOTE 3The titles of the publications referred to in this standard are listed on the inside back cover. 2 Definitions For the purposes of this Part of BS4479, the following definitions apply. 2.1 electroplated coating a coating obtained by electrodeposition for t

21、he purpose of securing an adherent metallic surface with properties or dimensions different from those of the basis material 2.2 electrodeposition the process of depositing a substance upon an electrode by electrolysis 2.3 autocatalytic coating deposition of a metallic coating by a controlled chemic

22、al reduction that is catalysed by the metal or alloy being deposited NOTEElectroless plating is a deprecated term. 2.4 barrel electroplating a process by which electroplated coatings are applied to articles in bulk in a rotating container 2.5 vat plating a process in which the articles to be electro

23、plated are independently attached to the cathode 2.6 brush electroplating a method of electroplating in which the electrolyte is contained in a pad or brush in contact with the anode. The pad or brush is applied to the part to be processed which is given opposite polarity 2.7 linishing a process whe

24、reby flat surfaces are directionally ground by means of an abrasive bonded to an endless flexible belt 2.8 polishing the smoothing of a metal surface 2.9 electropolishing the smoothing and brightening of a metal surface by making it anodic in an appropriate solution 2.10 chemical polishing immersion

25、 of a metal surface in a solution to produce improved surface smoothness 2.11 significant surface the part of the article covered or to be covered by the coating and for which the coating is essential for serviceability and/or appearance 3 Design considerations for electroplated articles 3.1 General

26、 Plating is a process of depositing a metal, or alloy, on to the surface of an article, usually made of a different metal. It is also possible to deposit metals on to a non-metallic material. Plating can be effected with the aid of an electric current (electroplating) or by immersion in an appropria

27、te solution (autocatalytic plating). There are three main reasons for the application of a metallic coating by electrodeposition: a) to provide an increased resistance to corrosion; b) for decorative purposes; c) for engineering applications. Articles to be plated are normally suspended on wires or

28、jigs in vats, or, in the case of articles that can be handled in bulk, are processed in rotating barrels.BS4479-2:1990 2 BSI 03-1999 Articles that require a polished finish are given a preliminary treatment of grinding or linishing, if necessary, and polishing, or are mass treated in a rotating barr

29、el or vibratory bowl with various abrasive media or polishing compounds. Chemical or electrochemical polishing can be used on certain metals or alloys and may be advantageous on small and intricately shaped articles. Blind holes, recesses and joint crevices, where compound and metal debris can lodge

30、, should be avoided if possible. An electrodeposited coating is generally not distributed uniformly over the surface of an article, but is likely to be thicker at prominences and corners where the current tends to concentrate, and thinner in depressions. Where plated articles have to be fitted toget

31、her, due allowance should be made for the thickness and distribution of the coating, e.g.on screw threads (see also BS3382). The use of autocatalytic processes (see clause4) frequently provides a much more uniform coating thickness on all surfaces. Generally, it is best to avoid large flat areas whi

32、ch can highlight basis metal imperfections. Convex or textured surfaces are to be preferred. Some deposits are less ductile than others and this should be borne in mind when application is considered for articles that might undergo some flexing in fabrication or service. The effect of certain platin

33、g processes on the mechanical properties of some substrates, and, hence, possibly on the serviceability of the coated article should be noted. For example, high strength steels (normally above1000 N/mm 2 ) are particularly susceptible to embrittlement by the hydrogen evolved during the pretreatment

34、or plating processes, and the effect can be relieved by suitable heat-treatment 2) . Consideration should be given to which of the following methods of plating is likely to be the more suitable, in view of the shape and size of the articles: 1) vat plating (see3.2); 2) barrel plating (see3.3); 3) se

35、lective plating (see3.4). Diagrams illustrating preferred and deprecated design features for articles to be electroplated are given in Appendix A. 3.2 Vat plating Account should be taken of the fact that articles to be vat plated should have jigging, or wiring points. They should be either located i

36、n the processing solutions in such a manner that liquid will not be trapped in seams or hollows, or be provided with drainage holes to prevent this problem. Provision of a means for releasing of air or evolved gas should be made where this may become trapped during plating. It is important that the

37、designer clearly indicates those significant surfaces intended to be coated for decorative purposes and/or corrosion protection. This will assist the electroplater in processing to ensure smooth deposits with as even a thickness as possible. The cost of plating a given area on an article will be gre

38、ater if the space occupied by the article in the vat is large. It is sometimes more economical to make the article in sections and assemble them after plating. 3.3 Barrel plating Design may have to take account of non-uniform distribution of coating thicknesses sometimes obtained in barrel plating.

39、Articles should not be prone to interlocking, which can result in damage as well as poor distribution of plating. Flat articles such as washers should be dimpled, if possible, to prevent sticking. Cup-shaped articles may be difficult to immerse in liquids and may drain ineffectively during transfer

40、from one process solution to the next; in such cases suitable drainage holes should be provided where possible. 3.4 Selective plating The following are examples of techniques that are available for the selective plating of articles: a) brush plating; NOTEBrush plating is normally used for local repa

41、ir work although large articles, too big to immerse in a vat can be processed by this method. Numerous metals and alloys can be brush plated and the entire operation is capable off being automated. b) application of a screen-printed or photo-mechanical mask prior to total immersion of the article in

42、 the process solutions; c) application of a mechanical mask for total immersion; d) controlled depth of immersion in the plating solution. 2) Appendix A of BS4479-1:1989 includes a list of some British Standards that give details of suitable treatments. e.g.BS1706 and BS4292-1. Further detailed info

43、rmation may also be found in Engineering coatings applications and properties No.16 in the series of Guides to Practice in Corrosion Control, published by National Corrosion Service of the National Physical Laboratory, obtainable from HMSO.BS4479-2:1990 BSI 03-1999 3 In the case of continuous automa

44、tic selective plating, in which mechanical masks can be used, the work is transported on a bandolier, or continuous strand, through an automatic in-line processing and plating line. The orientation of the articles on the bandolier or strand should permit selective or partial plating to be carried ou

45、t, if possible allowing a choice of techniques. The active area of the article should therefore be presented in the most accessible position. In some cases, a post-forming operation may be necessary and it is important to note that forming of the active area after plating is generally inadvisable. T

46、o facilitate economical processing speeds, the arrangement of articles should avoid line astern configuration. Close pitched ladder formations, with multiple rows, are preferred if possible. The selvedge, carrier bar or bandolier should be sufficiently strong to withstand several S-bends during proc

47、essing, and should be capable of carrying the current for the electrolytic processes used, taking into account the high current densities common to this type of processing. Twist and edge-wise bowing (sabre) should be avoided, if precise selective plating of small areas is required. These adverse ch

48、aracteristics are more serious when a punched strand has more than one carrier bar (see Figure 17 for recommended design practice and tolerances). Pitch errors should not be cumulative and tolerances on all features should generally reflect the precision required in terms of area and location of the

49、 selective plating. If the bandoliered articles are tubular, e.g.socket contacts, they should be free draining and accessible to spray rinses and forced air drying. Components should be easily removable, e.g.for the purposes of testing, without recourse to cutting the strand. 4 Design considerations for autocatalytically plated articles The principal design features given in clause3 for electroplated coatings and illustrated in Appendix A are equally applicable to articles required to be autocatalytically plated. The coating

展开阅读全文
相关资源
  • BS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdfBS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdf
  • BS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdfBS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdf
  • BS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdfBS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdf
  • BS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdfBS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdf
  • BS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdfBS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf
  • BS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdfBS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdf
  • BS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdfBS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdf
  • BS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdfBS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdf
  • BS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdfBS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdf
  • BS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdfBS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > BS

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1