BS EN 1453-1-2017 Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings Unplasticized poly(vinyl chloride) (PV.pdf

上传人:tireattitude366 文档编号:549012 上传时间:2018-12-09 格式:PDF 页数:34 大小:1.93MB
下载 相关 举报
BS EN 1453-1-2017 Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings Unplasticized poly(vinyl chloride) (PV.pdf_第1页
第1页 / 共34页
BS EN 1453-1-2017 Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings Unplasticized poly(vinyl chloride) (PV.pdf_第2页
第2页 / 共34页
BS EN 1453-1-2017 Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings Unplasticized poly(vinyl chloride) (PV.pdf_第3页
第3页 / 共34页
BS EN 1453-1-2017 Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings Unplasticized poly(vinyl chloride) (PV.pdf_第4页
第4页 / 共34页
BS EN 1453-1-2017 Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside buildings Unplasticized poly(vinyl chloride) (PV.pdf_第5页
第5页 / 共34页
亲,该文档总共34页,到这儿已超出免费预览范围,如果喜欢就下载吧!
资源描述

1、BS EN 1453-1:2017Plastics piping systems with structured-wall pipes for soiland waste discharge (low and high temperature) insidebuildings - Unplasticized poly(vinyl chloride) (PVC-U) -Part 1: Specifications for pipes andthe systemBSI Standards PublicationWB11885_BSI_StandardCovs_2013_AW.indd 1 15/0

2、5/2013 15:06BS EN 1453-1:2017 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of EN 1453-1:2017. It supersedes BS EN 1453-1:2000 which is withdrawn.The UK participation in its preparation was entrusted to Technical Committee PRI/88/1, Plastics piping for non-pressure

3、applications.A list of organizations represented on this committee can be obtained on request to its secretary.This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. The British Standards Institution 2017.Published

4、by BSI Standards Limited 2017ISBN 978 0 580 87651 6 ICS 23.040.01; 23.040.05; 91.140.80 Compliance with a British Standard cannot confer immunity from legal obligations.This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 January 2017.Amendment

5、s/corrigenda issued since publicationDate T e x t a f f e c t e dBS EN 1453-1:2017EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 1453-1 January 2017 ICS 23.040.01; 23.040.05; 91.140.80 Supersedes EN 1453-1:2000English Version Plastics piping systems with structured-wall pipes for soil and wast

6、e discharge (low and high temperature) inside buildings - Unplasticized poly(vinyl chloride) (PVC-U) - Part 1: Specifications for pipes and the system Systmes de canalisations en plastique avec des tubes paroi structure pour lvacuation des eaux-vannes et des eaux uses ( basse et haute temprature) li

7、ntrieur des btiments - Poly(chlorure de vinyle) non plastifi (PVC-U) - Partie 1 : Spcifications pour tubes et le systme Kunststoff-Rohrleitungssysteme mit Rohren mit profilierter Wandung zum Ableiten von Abwasser (niedriger und hoher Temperatur) innerhalb von Gebuden - Weichmacherfreies Polyvinylchl

8、orid (PVC-U) - Teil 1: Anforderungen an Rohre und das Rohrleitungssystem This European Standard was approved by CEN on 29 October 2016. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national

9、standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN member. This European Standard exists in three official versions (English, French, German). A version

10、in any other language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech

11、 Republic, Denmark, Estonia, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United King

12、dom. EUROPEAN COMMITTEE FOR STANDARDIZATION COMIT EUROPEN DE NORMALISATION EUROPISCHES KOMITEE FR NORMUNG CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels 2017 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1453-1:

13、2017 EBS EN 1453-1:2017EN 1453-1:2017 (E) 2 Contents Page European foreword . 3 1 Scope 4 2 Normative references 4 3 Terms and definitions, symbols and abbreviations . 6 3.1 Terms and definitions . 6 3.2 Symbols . 8 3.3 Abbreviations . 9 4 Material . 9 4.1 Raw material . 9 4.2 Utilization of non-vir

14、gin material . 9 4.3 Sealing ring retaining means 9 5 General characteristics 10 5.1 Appearance . 10 5.2 Colour . 10 6 Geometrical characteristics . 10 6.1 General . 10 6.2 Dimensions of pipes 10 6.3 Dimensions of sockets 13 7 Mechanical characteristics . 19 7.1 General requirements 19 7.2 Additiona

15、l requirements . 20 8 Physical characteristics . 21 9 Performance requirements 22 10 Sealing rings . 22 11 Adhesives 22 12 Marking 22 12.1 General . 22 12.2 Minimum required marking 23 12.3 Additional marking . 23 Annex A (informative) Guidance for calcium carbonate additives . 24 A.1 Composition of

16、 calcium carbonate additives . 24 A.2 Physical properties of calcium carbonate additive . 24 Annex B (normative) Utilization of non-virgin material . 25 B.1 Own reprocessed material 25 B.2 External reprocessed and recycled materials with agreed specification 25 B.3 External reprocessed and recycled

17、material not covered by an agreed specification . 28 Annex C (informative) Product standards . 29 Bibliography . 30 BS EN 1453-1:2017EN 1453-1:2017 (E) 3 European foreword This document (EN 1453-1:2017) has been prepared by Technical Committee CEN/TC 155 “Plastics piping systems and ducting systems”

18、, the secretariat of which is held by NEN. This document supersedes EN 1453-1:2000. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by July 2017, and conflicting national standards shall be withdrawn

19、 at the latest by July 2017. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN shall not be held responsible for identifying any or all such patent rights. This standard is a part of a System Standard for plastics piping systems

20、 of a particular material for a specified application. There are a number of such System Standards. System Standards are based on the results of the work undertaken in ISO/TC 138 “Plastics pipes, fittings and valves for the transport of fluids”, which is a Technical Committee of the International Or

21、ganization for Standardization (ISO). They are supported by separate standards on test methods to which references are made throughout the System Standard. The System Standards are consistent with general standards on functional requirements and on recommended practice for installation. EN 1453 cons

22、ists of the following parts, under the general title Plastics piping systems with structured-wall pipes for soil and waste discharge (low and high temperature) inside building Unplasticized poly(vinyl chloride) (PVC-U) 1): Part 1: Requirements for pipes and the system (the present standard) Part 2:

23、Guidance for the assessment of conformity (under preparation) According to the CEN-CENELEC Internal Regulations, the national standards organisations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estoni

24、a, Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the United Kingdom. 1) EN 1453 does n

25、ot cover a recommended practice for installation. A recommended practice for installation is covered by the following European Technical Report: CEN/TR 13801, Plastics piping systems for soil and waste discharge (low and high temperature) within the building structure Thermoplastics Recommended prac

26、tice for installation. BS EN 1453-1:2017EN 1453-1:2017 (E) 4 1 Scope This part of EN 1453 specifies the requirements for structured-wall unplasticized poly(vinyl chloride) (PVC-U) pipes and the system intended to be used for soil and waste discharge applications (low and high temperature) inside bui

27、ldings (application area code “B”) NOTE 1 The intended use is reflected in the marking of products by “B”. This part of EN 1453 is also applicable to structured-wall unplasticized poly(vinyl chloride) (PVC-U) pipes, and the system intended for the following purposes: ventilating part of the pipework

28、 in association with discharge applications; rainwater pipework inside building. It also specifies the test parameters for the test methods referred to in this standard. NOTE 2 Single layer foamed PVC-U pipes and spirally-formed PVC-U pipes are not covered by this standard. This standard covers a ra

29、nge of nominal sizes and gives recommendations concerning colours. NOTE 3 It is the responsibility of the purchaser or specifier to make the appropriate selections from these aspects, taking into account their particular requirements and any relevant national regulations and installation practices o

30、r codes. For external above ground application additional requirements depending on the climatic conditions should be agreed between the manufacturer and the user. NOTE 4 Pipes conforming to this standard are normally associated with fittings conforming to EN 13291 1. Pipes, fittings and components

31、conforming to any of the product standards listed in Annex C can also be used with pipes conforming to this standard, provided they conform to the requirements for joint dimensions given in Clause 6 and to the requirements in Table 11. NOTE 5 Joints and adhesives are considered to be part of the sys

32、tem as covered in the scope. NOTE 6 Products conforming to this standard may be submitted to national requirements on fire regulation. 2 Normative references The following documents, in whole or in part, are normatively referenced in this document and are indispensable for its application. For dated

33、 references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 681-1, Elastomeric seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 1: Vulcanized rubber EN 681-

34、2, Elastomeric Seals - Materials requirements for pipe joint seals used in water and drainage applications - Part 2: Thermoplastic elastomers EN 1905, Plastics piping systems - Unplasticized poly(vinyl chloride) (PVC-U) pipes, fittings and material - Method for assessment of the PVC content based on

35、 total chlorine content EN 10204:2004, Metallic products - Types of inspection documents EN 14680, Adhesives for non-pressure thermoplastics piping systems - Specifications EN 15346:2014, Plastics - Recycled plastics - Characterization of poly(vinyl chloride) (PVC) recyclates BS EN 1453-1:2017EN 145

36、3-1:2017 (E) 5 EN ISO 306, Plastics - Thermoplastic materials - Determination of Vicat softening temperature (VST) (ISO 306:2013) EN ISO 472, Plastics - Vocabulary (ISO 472) EN ISO 1043-1, Plastics - Symbols and abbreviated terms - Part 1: Basic polymers and their special characteristics (ISO 1043-1

37、) EN ISO 1183-1, Plastics - Methods for determining the density of non-cellular plastics - Part 1: Immersion method, liquid pyknometer method and titration method (ISO 1183-1) EN ISO 2505, Thermoplastics pipes - Longitudinal reversion - Test method and parameters (ISO 2505) EN ISO 3126, Plastics pip

38、ing systems - Plastics components - Determination of dimensions (ISO 3126) EN ISO 3451-5, Plastics - Determination of ash - Part 5: Poly(vinyl chloride) (ISO 3451-5) EN ISO 6259-1, Thermoplastics pipes - Determination of tensile properties - Part 1: General test method (ISO 6259-1) EN ISO 13229, The

39、rmoplastics piping systems for non-pressure applications - Unplasticized poly(vinyl chloride) (PVC-U) pipes and fittings - Determination of the viscosity number and K-value (ISO 13229) ISO 2507-1, Thermoplastics pipes and fittings Vicat softening temperature Part 1: General test method ISO 3127, The

40、rmoplastics pipes Determination of resistance to external blows Round-the-clock method ISO 6259-2, Thermoplastics pipes Determination of tensile properties Part 2: Pipes made of unplasticized poly(vinyl chloride) (PVC-U), chlorinated poly (vinyl chloride) (PVC-C) and high-impact poly (vinyl chloride

41、) (PVC-HI) ISO 9852, Unplasticized poly(vinyl chloride) (PVC-U) pipes Dichloromethane resistance at specified temperature (DCMT) Test method ISO 11173:1994, Thermoplastics pipes Determination of resistance to external blows Staircase method ISO 13254, Thermoplastics piping systems for non-pressure a

42、pplications Test method for watertightness ISO 13255, Thermoplastics piping systems for soil and waste discharge inside buildings Test method for airtightness of joints ISO 13257:2010, Thermoplastics piping systems for non-pressure applications Test method for resistance to elevated temperature cycl

43、ing ISO 18373-1, Rigid PVC pipes Differential scanning calorimetry (DSC) method Part 1: Measurement of the processing temperature BS EN 1453-1:2017EN 1453-1:2017 (E) 6 3 Terms and definitions, symbols and abbreviations 3.1 Terms and definitions For the purposes of this document, the terms and defini

44、tions given in EN ISO 472 and EN ISO 1043-1 and the following apply. 3.1.1 application area code code used in the marking of pipes and fittings to indicate the application area(s) for which they are intended, as follows: B: application area code for components intended for use above ground inside th

45、e building Note 1 to entry: Other application area codes D, BD, U and UD not covered by this standard are defined elsewhere, e.g. in EN 13291 1 and EN 14011 2. 3.1.2 structured-wall pipe pipe with smooth internal and smooth external surfaces, with two solid PVC layers, or in which the inner and oute

46、r solid PVC layers are connected by foamed or non-foamed PVC intermediate layers Note 1 to entry: Pipe in which the inner and outer solid PVC layers are connected by foamed PVC intermediate layers is also called foam core pipe. 3.1.3 solid layer layer made of non-foamed PVC 3.1.4 foamed PVC poly(vin

47、yl chloride) which contains numerous small gas cells distributed throughout the mass Note 1 to entry: Foam layers have a density less than 1,37 g/cm3when measured according to EN ISO 1183-1. 3.1.5 nominal size DN numerical designation of the size of a component, other than a component designated by

48、thread size, which is approximately equal to the manufacturing dimension, in millimetres 3.1.6 nominal size DN/OD nominal size, related to the outside diameter 3.1.7 nominal outside diameter dnspecified outside diameter, in millimetres, assigned to a nominal size DN/OD BS EN 1453-1:2017EN 1453-1:201

49、7 (E) 7 3.1.8 outside diameter devalue of the measurement of the outside diameter through its cross-section at any point of a pipe or spigot end of a fitting, rounded up to the next greater 0,1 mm 3.1.9 mean outside diameter demvalue of the measurement of the outer circumference of a pipe or spigot end of a fitting in any cross-section, divided by ( 3,142), rounded up to the next greater 0,1 mm 3.1.10 inside diameter of a socket dsvalue of measurement of the inside diameter through its cross-section at any po

展开阅读全文
相关资源
  • BS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdfBS ISO IEC 29150-2011 Information technology Security techniques Signcryption《信息技术 安全技术 签密》.pdf
  • BS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdfBS ISO IEC 15408-1-2009 Information technology - Security techniques - Evaluation criteria for IT Security - Introduction and general model《信息技术 安全技术 IT安全评价准则 一.pdf
  • BS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdfBS ISO 7295-1988+A1-2014 Tyre valves for aircraft Interchangeability dimensions《飞机轮胎汽门嘴 互换性尺寸》.pdf
  • BS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdfBS ISO 15118-1-2013 Road vehicles Vehicle to grid communication interface General information and use-case definition《道路车辆 车辆到电力通讯接口 通用信息和使用案例定义》.pdf
  • BS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdfBS ISO 13765-2-2004 Refractory mortars - Determination of consistency using the reciprocating flow table method《耐熔灰浆 使用往复流动表法测定一致性》.pdf
  • BS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdfBS ISO 10998-2008+A1-2014 Agricultural tractors Requirements for steering《农业拖拉机 操纵要求》.pdf
  • BS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdfBS Z 9-1998 Space data and information transfer systems - Advanced orbiting systems - Networks and data links - Architectural specification《空间数据和信息传输系统 高级轨道系统 网络和数据链接 结构规范》.pdf
  • BS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdfBS Z 7-1998 Space data and information transfer systems - ASCII encoded English《空间数据和信息传输系统 ASCII 编码英语》.pdf
  • BS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdfBS Z 5-1997 Space data and information transfer systems - Standard formatted data units - Control authority procedures《航天数据和信息发送系统 标准格式数据单元 控制授权程序》.pdf
  • BS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdfBS Z 4-1997 Space data and information transfer systems - Standard formatted data units - Structure and construction rules《航天数据和信息传输系统 标准格式数据单元 结构和构造规则》.pdf
  • 猜你喜欢
    相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > BS

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1