1、| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BRITISH STANDARD BS EN 1592-3 : 1998 The E
2、uropean Standard EN 1592-3 : 1997 has the status of a British Standard ICS 77.150.10 NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAW Aluminium and aluminium alloys HF seam welded tubes Part 3. Tolerances on dimensions and form for circular tubesThis British Standard, having be
3、en prepared under the direction of the Engineering Sector Board, was published under the authority of the Standards Board and comes into effect on 15 March 1998 BSI 1998 ISBN 0 580 28821 8 BS EN 1592-3 : 1998 Amendments issued since publication Amd. No. Date Text affected National foreword This Brit
4、ish Standard is the English language version of EN 1592-3 : 1997 published by the European Committee for Standardization (CEN). Together with BS EN 1592-1 : 1998, BS EN 1592-2 : 1998 and BS EN 1592-4 : 1998 it supersedes BS 4300-1 : 1967 which is withdrawn. The UK participation in its preparation wa
5、s entrusted by Technical Committee NFE/35, Light metals and their alloys, to Subcommittee NFE/35/5, Wrought aluminium and aluminium alloys, which has the responsibility to: aid enquirers to understand the text; present to the responsible European committee any enquiries on the interpretation, or pro
6、posals for change, and keep the UK interests informed; monitor related international and European developments and promulgate them in the UK. A list of organizations represented on this committee can be obtained on request to its secretary. Cross-references The British Standards which implement inte
7、rnational or European publications referred to in this document may be found in the BSI Standards Catalogue under the section entitled International Standards Correspondence Index, or by using the Find facility of the BSI Standards Electronic Catalogue. Compliance with a British Standard does not of
8、 itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, the EN title page, pages 2 to 6, an inside back cover and a back cover.CEN European Committee for Standardization Comite Europe en de Normalisation Europa isches Komitee fu
9、r Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1997 CEN All rights of exploitation in any form and by any means reserved worldwide for CEN national Members. Ref. No. EN 1592-3 : 1997 E EUROPEAN STANDARD EN 1592-3 NORME EUROPE ENNE EUROPA ISCHE NORM October 1997 ICS 77.150.10 Desc
10、riptors: Aluminium, aluminium alloys, aluminium tubes, welded tubes, dimensional tolerances, form tolerances English version Aluminium and aluminium alloys HF seam welded tubes Part 3: Tolerances on dimensions and form for circular tubes Aluminium et alliages daluminium Tubes e lectrosoude s HF Part
11、ie 3: Tole rances sur dimensions et forme des tubes a section circulaire Aluminium und Aluminiumlegierungen HF-la ngsnahtgeschweite Rohre Teil 3: Grenzabmae und Formtoleranzen fu r Rundrohre This European Standard was approved by CEN on 19 September 1997. CEN members are bound to comply with the CEN
12、/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to
13、any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
14、 CEN members are the national standards bodies of Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom.Page 2 EN 1592-3 : 1997 BSI 1998 Foreword This European Sta
15、ndard has been prepared by Technical Committee CEN/TC 132, Aluminium and aluminium alloys, the secretariat of which is held by AFNOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by April 1998, an
16、d conflicting national standards shall be withdrawn at the latest by April 1998. Within its programme of work, Technical Committee CEN/TC 132 entrusted CEN/TC 132/WG 12, HF seam welded tubes, to prepare the following standard: EN 1592-3 Aluminium and aluminium alloys HF seam welded tubes Part 3: Tol
17、erances on dimensions and form for circular tubes This standard is part of a series of four standards. The other standards deal with: EN 1592-1 Aluminium and aluminium alloys HF seam welded tubes Part 1: Technical conditions for inspection and delivery EN 1592-2 Aluminium and aluminium alloys HF sea
18、m welded tubes Part 2: Mechanical properties EN 1592-4 Aluminium and aluminium alloys HF seam welded tubes Part 4: Tolerances on dimensions and form for square, rectangular and shaped tubes According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following count
19、ries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom. Contents Page Foreword 2 1 Scope 3 2 Normative refer
20、ences 3 3 Dimensions 3 4 Tolerances on dimensions 3 4.1 External diameter (ovality included) 3 4.2 Thickness 3 4.3 Length 3 5 Tolerances on form 4 5.1 Straightness 4 5.2 Perpendicularity of cut ends 4 5.3 Spiralling 5 5.4 Deburring 5 5.5 Weld fin 6Page 3 EN 1592-3 : 1997 BSI 1998 1 Scope This Part o
21、f EN 1592 specifies the tolerances on dimensions and form of circular HF seam welded tubes with a diameter up to and including 80 mm and a wall thickness up to and including 2,5 mm. These tubes are manufactured from rolled aluminium alloy strip longitudinally welded in a continuous process by the pa
22、ssage of an electric current across the abutting edges without the addition of filler metal. This standard also applies to tubes manufactured from aluminium alloy strip which is painted, lacquered or anodized prior to forming. Technical conditions for inspection and delivery are specified in EN 1592
23、-1. 2 Normative references This European Standard incorporates by dated or undated references, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or r
24、evisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 1592-1 Aluminium and aluminium alloys HF seam welded tubes Part 1: Technical conditions fo
25、r inspection and delivery 3 Dimensions The dimensions of tubes shall be designated by the outside diameter and wall thickness. 4 Tolerances on dimensions 4.1 External diameter (ovality included) The outside diameter measured at any point (excluding the first 100 mm from each end) shall be within the
26、 tolerances given in table 1. Table 1. Tolerances on outside diameter (ovality included) Dimensions in millimetres Nominal outside diameter D Tolerances 8# D# 15 0,10 15 40 mm, the measurements shall be performed using a vernier rule with an accuracy of at least 1/50th of a millimetre. All measureme
27、nts shall be taken at least 100 mm from the end of the tube. 4.2 Thickness The tolerances on thickness shall be in accordance with table 2. Table 2. Tolerances on thickness Dimensions in millimetres Nominal thickness t Tolerances 0,6# t# 1,0 0,05 1,0 t# 2,5 0,08 These tolerances are not applicable t
28、o the weld fin. Other thicknesses and tolerances are available by written agreement between producer and purchaser. 4.3 Length Tubes shall be supplied in one of the following ways: random lengths, subject to a tolerance of 100 mm; specified cut lengths with the tolerances in accordance with table 3.
29、 Table 3. Tolerances on specified cut length Dimensions in millimetres Specified length L Tolerances L 1 000 1,0 1 000# L 3 000 1,5 3 000# L 7 000 2,0 7 000# L 3,0 In case of dispute the length shall be measured as shown in figure 1, the tube being placed on a flat surface with 908 angle plates abut
30、ted on each end. The measurement shall be taken across the total gap l between plates.Page 4 EN 1592-3 : 1997 BSI 1998 Figure 1. Length measurement 5 Tolerances on form 5.1 Straightness Deviation from straightness shall be measured as shown in figure 2. Figure 2. Measurement of deviation from straig
31、htness The deviation F measured on any 1 m length taken at random along the length of the tube, shall not exceed 1,6 mm. The maximum deviation E, expressed in millimetres, measured over the entire length of the tube shall not exceed 1,63 L (in metres). 5.2 Perpendicularity of cut ends The deviation
32、from perpendicularity of the cut ends (see figure 3) shall not exceed the tolerances given in table 4. Figure 3. Measurement of deviation from perpendicularityPage 5 EN 1592-3 : 1997 BSI 1998 Table 4. Tolerances on perpendicularity of cut ends Dimensions in millimetres Nominal outside diameter D Tol
33、erance P 8# D# 10 0,075 10 D# 15 0,10 15 D# 30 0,20 30 D# 50 0,35 50 D# 70 0,50 70 D 0,75 For specific cut length orders, this deviation shall be included in the total length tolerance (see 4.3). 5.3 Spiralling Spiralling shall be measured on a 1 m section at any position along the length of the tub
34、e (see figure 4). It shall be expressed in degrees per metre. The standard tolerance b shall be# 28/m. The maximum permitted spiralling over the entire length of the tube shall be less than the value over 1 m multiplied by the length (in metres). OO9: geometrical axis of the tube AC: seam without sp
35、iralling BC: seam to be controlled Figure 4. Measurement of spiralling 5.4 Deburring Tubes shall not be supplied deburred (i.e. minimal end burrs which do not adversely affect the end use shall be permissible). If deburred tube ends are required, these shall be agreed between producer and purchaser
36、and specified in the order.Page 6 EN 1592-3 : 1997 BSI 1998 5.5 Weld fin The external weld fin shall be removed completely (i.e. flush with the outside surface of the tube). NOTE. Normally the total thickness t s at the weld should not exceed 2,2 times the thickness t of the tube (see figure 5). Thi
37、s applies to tubes with a wall thickness of 0,9 mm or greater. Figure 5. Weld finblankBSI 389 Chiswick High Road London W4 4AL | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | |
38、 | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | BSI British Standards Institution BSI is the independent national body responsible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Ro
39、yal Charter. Revisions British Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an
40、 inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel: 020 8996 9000. Fax: 020 8996 7400. BSI offers members an individual updating service called PLUS which ensu
41、res that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel: 020 8996 9001. Fax: 020 8996 7001. In response to orders for international standards, it i
42、s BSI policy to supply the BSI implementation of those that have been published as British Standards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporter
43、s Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel: 020 8996 7111. Fax: 020 8996 7048. Subscribing members of BSI are kept up to date with standards developments and receive substantial di
44、scounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel: 020 8996 7002. Fax: 020 8996 7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international stand
45、ardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not pre
46、clude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel: 020 8996 7070.
