1、BRITISH STANDARD AEROSPACE SERIES BS EN 2143:1993 Rivets, solid, universal head, in aluminium1050A, inch based series The European Standard EN 2143:1992 has the status of a British Standard UDC 621.884.2-034.715:629.7BSEN2143:1993 This British Standard, having been prepared under the directionof the
2、 Aerospace Standards Policy Committee, waspublished under the authorityof the Standards Boardand comes into effect on 15February1993 BSI 11-1999 The following BSI references relate to the work on this standard: Committee reference ACE/12 Draft for comment 89/79398 DC ISBN 0 580 21973 9 Cooperating o
3、rganizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark Dansk Stan
4、dardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority of Ireland Italy Ente Na
5、zionale Italiano di Unificazione Luxembourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normalizacin y Certificacin Sweden Standardiseringskommissionen i Sve
6、rige Switzerland Association suisse de normalisation United Kingdom British Standards Institution Amendments issued since publication Amd. No. Date CommentsBSEN2143:1993 BSI 11-1999 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 1 Scope 3 2 Normative ref
7、erences 3 3 Required characteristics 3 4 Designation 5 5 Marking 5 6 Technical specification 5 National annex NA (informative) Committees responsible Inside back cover National annex NB (informative) Cross-references Inside back cover Figure 1 3 Table 1 4 Table 2 4 Table 3 5BSEN2143:1993 ii BSI 11-1
8、999 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN2143:1992 Aerospace series Rivets, solid, universal head, in aluminium1050A, inch based series, published by the European Committee f
9、or Standardization (CEN). EN2143:1992 was produced as a result of international discussions in which the United Kingdom took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct applica
10、tion. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, theEN title page, pages2to6, an inside back cover and a back cover. This standard has been updated (see c
11、opyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2143 November 1992 UDC 621.884.2-034.715:629.7 Descriptors: Aircraft industry, full rivet, round head rivet, aluminium
12、, dimension, designation English version Aerospace series Rivets, solid, universal head, in aluminium 1050A, inch based series Srie arospatiale Rivets ordinaires, tte ronde aplatie, en aluminium 1050A, srie base inches Luft- und Raumfahrt Vollniete, mit Universalkopf, aus Aluminium 1050A, Inch-Reihe
13、 This European Standard was approved by CEN on1992-11-16. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical referenc
14、es concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into
15、its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Swit
16、zerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1992 Copyright reserved to CEN members Ref. No. EN 2143:1992 EEN2143:1992 2 BSI 11-1999 Foreword This European
17、 Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this standard has successively received the approval of the National Associations and the Official Services of the membe
18、r countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May1993, and conflicting national standards shall be withdrawn at the latest by May1993. Acc
19、ording to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the UnitedKingdom.EN2
20、143:1992 BSI 11-1999 3 1 Scope This standard specifies the characteristics of solid rivets, with universal head, inch based series, in aluminium for maximum operating temperature120 C. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other pub
21、lications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revis
22、ion. For undated references the latest edition of the publication referred to applies. EN 2000, Aerospace series Quality assurance EN aerospace products Approval of the quality system of manufacturers. EN 2114, Aerospace series Aluminium 1050A-H14 wire for solid rivets D k 10 mm 1) . EN 2345, Alumin
23、ium and aluminium alloy rivets Technical specification Aerospace series 1) . EN 2424, Aerospace series Identification marking of standard fasteners 1) . 3 Required characteristics 3.1 Configuration Dimensions Masses SeeFigure 1 andTable 1 andTable 2. Dimensions and tolerances are expressed in millim
24、etres. 3.2 Material EN 2114 The rivet shall be delivered in H14 condition. 1) Published as AECMA standard at the date of publication of the present standard Figure 1 EN2143:1992 4 BSI 11-1999 Table 1 Table 2 Diameter code D 1 a D 2 D 3 L 2 L 3 R 1 R 2 max. min. max. min. max. min. 0.08 016 1,65 1,55
25、 3,35 3,05 1,6 1,2 0,7 2 024 2,45 2,35 5 4,5 2,4 1,8 1 1,45 2,9 0,15 032 3,25 3,15 6,7 6 3,2 2,4 1,4 3,9 a D 1max. may increase by 0,03, over length L 3 . Diameter code 016 024 032 Length Mass akg/1000 pieces Code L 1 004 4 0,030 0,074 0,149 005 5 0,036 0,087 0,172 006 6 0,042 0,100 0,194 007 7 0,04
26、7 0,113 0,217 008 8 0,053 0,125 0,239 009 9 0,059 0,138 0,262 010 10 0,064 0,150 0,284 011 11 0,070 0,163 0,307 012 12 0,075 0,176 0,329 014 14 0,087 0,201 0,374 016 16 0,100 0,225 0,419 018 18 0,250 0,465 020 20 0,275 0,510 022 22 0,301 0,555 024 24 0,326 0,600 026 26 0,351 0,645 028 28 0,377 0,691
27、 030 30 0,402 0,736 032 32 0,427 0,781 035 35 0,466 0,849 040 40 0,960 a Approximate values, calculated on the basis of 2,76 kg/dm 3 , given for information purpose only +0,2 0 +0,5 0EN2143:1992 BSI 11-1999 5 4 Designation NOTEIf necessary, the originator codeI9005 shall be placed between the descri
28、ption block and the identity block. 5 Marking 5.1 Rivet identification EN 2424, style G 5.2 Material identification SeeTable 3. Table 3 6 Technical specification EN2345 except for approval of manufacturers, see EN2000. Colour Code None - (hyphen) Red F The method of achieving is at the manufacturers
29、 option.6 blankBSEN2143:1993 BSI 11-1999 National annex NA (informative) Committees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/12, upon which the following bodi
30、es were represented: Association of Electronics, Telecommunications and Business Equipment Industries British Industrial Fasteners Federation Ministry of Defence Society of British Aerospace Companies Ltd. National annex NB (informative) Cross-references The British Standards corresponding to the Eu
31、ropean Standards referred to in the text are identical in number and title with those given in clause2, with the exception of EN2114, EN2345 and EN2424 for which no corresponding British Standards exist.BS EN 2143:1993 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is th
32、e independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that
33、 they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, th
34、e identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and fo
35、reign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information
36、 on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the In
37、formation Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:0208996
38、7001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or tr
39、ansmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
