1、BRITISH STANDARD AEROSPACE SERIES BS EN 2145:1994 Rivets, solid, universal head, in aluminium alloy2117, anodized or chromated, inch based series The European Standard EN2145:1994 has the status of a British Standard UDC 621.884.2-034.715:629.7BSEN2145:1994 This British Standard, having been prepare
2、d under the directionof the Aerospace Standards Policy Committee, waspublished under the authorityof the Standards Boardand comes into effect on 15November1994 BSI12-1999 The following BSI references relate to the work on this standard: Committee referenceACE/12 Draft for comment93/712078 DC ISBN 0
3、580 22627 1 Cooperating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normali
4、sation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normunge.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority
5、of Ireland Italy Ente Nazionale Italiano di Unificazione Luxembourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normalizacin y Certificacin Sweden Standardis
6、eringskommissionen i Sverige Switzerland Association suisse de normalisation United Kingdom British Standards Institution Amendments issued since publication Amd. No. Date CommentsBSEN2145:1994 BSI 12-1999 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 1
7、 Scope 3 2 Normative references 3 3 Required characteristics 3 4 Designation 6 5 Marking 6 6 Technical specification 6 National annex NA (informative) Committees responsible Inside back cover National annex NB (informative) Cross-references Inside back cover Figure 1 4 Figure 2 6 Table 1 3 Table 2 4
8、 Table 3 5 Table 4 6BSEN2145:1994 ii BSI 12-1999 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN2145:1994 Aerospace series Rivets, solid, universal head, in aluminium alloy2117, anodiz
9、ed or chromated, inch based series, published by the European Committee for Standardization (CEN). EN2145:1994 was produced as a result of international discussions in which the UnitedKingdom took an active part. A British Standard does not purport to include all the necessary provisions of a contra
10、ct. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2 to6, an in
11、side back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN2145 July1994 UDC 621.884.2-034.715:629.7 Descri
12、ptors: Aircraft industry, full rivets, round head rivets, aluminium alloy, anodizing, chromating, dimensions, designation, marking English version Aerospace series Rivets, solid, universal head, in aluminium alloy2117, anodized or chromated, inch based series Srie arospatiale Rivets ordinaires, tte
13、ronde aplatie, en alliage daluminium2117, anodiss ou chromats, srie base inches Luft- und Raumfahrt Vollniete, mit Universalkopf, aus Aluminiumlegierung2117, anodisiert oder chromatiert, Inch-Reihe This European Standard was approved by CEN on1994-07-27. CEN members are bound to comply with the CEN/
14、CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to a
15、ny CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions.
16、CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CEN European Committee for Standardization Comit Europen de Normalisation Eu
17、ropisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1994 Copyright reserved to CEN members Ref. No.EN2145:1994 EEN2145:1994 BSI 12-1999 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquirie
18、s and votes carried out in accordance with the rules of this Association, this draft has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a
19、 national standard, either by publication of an identical text or by endorsement, at the latest by January1995, and conflicting national standards shall be withdrawn at the latest by January1995. In accordance with the CEN/CENELEC Internal Regulations the following countries are bound to implement t
20、his European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom.EN2145:1994 BSI 12-1999 3 1 Scope This standard specifies the characteristics of solid rivets, universa
21、l head, in aluminium alloy2117, anodized or chromated, inch based series, for maximum operating temperature120 C. 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate place
22、s in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referr
23、ed to applies. EN2000, Aerospace series Quality assurance EN aerospace products Approval of the quality system of manufacturers. EN2101, Aerospace series Chromic acid anodizing of aluminium and wrought aluminium alloys. EN2284, Aerospace series Sulphuric acid anodizing of aluminium and wrought alumi
24、nium alloys. EN2345, Aluminium and aluminium alloy rivets Technical specification Aerospace series 1) . EN2424, Aerospace series Marking of aerospace products 1) . EN2437, Aerospace series Chromate conversion coatings (yellow) for aluminium and aluminium alloys 2) . QQ-A-430C, Federal specification
25、Aluminium alloy rod and wire; for rivets and cold heading 3) . 3 Required characteristics 3.1 Configuration Dimensions Masses See Figure 1 and Table 2 and Table 3. Dimensions and tolerances are expressed in millimetres and apply after surface treatment. 3.2 Material Aluminium alloy2117-H13 according
26、 to QQ-A-430C(1,6mmk Dk 10mm). The rivet shall be delivered inT4 condition. 3.3 Surface treatment See Table 1. Table 1 1) Published as AECMA Standard at the date of publication of this standard 2) In preparation at the date of publication of this standard 3) Published by: Superintendent of Documents
27、, US Government Printing Office, Washington, DC20402, UnitedStates Nature Code EN2284B A EN2437-2A B EN2101B a Not colored rivets -(hyphen) Violet-colored rivets F a Specified in the AECMA Standard. Shall be replaced by EN2284B.EN2145:1994 4 BSI 12-1999 Table 2 Figure 1 Diameter code D 1 a D 2 D 3 D
28、 4 L 2 L 3 L 4 R 1 R 2 max. min. max. min. max. min. max. min. max. min. 0,08 024 2,45 2,35 5 4,5 2,4 1,8 1,9 1,6 1 1,4 0,8 0,5 2,9 0,15 032 3,25 3,15 6,7 6 3,2 2,4 2,6 2,3 1,4 1 0,7 3,9 036 3,65 3,55 7,5 6,8 3,6 2,7 2,9 2,5 1,6 1,6 1,1 0,7 4.4 0,25 040 4,05 3,94 8,3 7,5 4 3 3,2 2,8 1,7 1,2 0,8 4,9
29、048 4,85 4,73 10 9 4,8 3,6 3,8 3,3 2 2 1,5 1 5,9 a D 1max. may increase by0,03, over length L 3 . +0,2 0EN2145:1994 BSI 12-1999 5 Table 3 Diameter code 024 032 036 040 048 Length a Mass b a Mass b a Mass b a Mass b a Mass b code N R N R N R N R N R 004 4 0,083 0,176 0,227 005 5 0,095 0,198 0,254 006
30、 6 0,107 0,220 0,280 0,373 007 7 0,119 0,242 0,306 0,408 008 8 0,131 0,264 0,332 0,443 0,664 009 9 0,143 0,286 0,358 0,478 0,714 010 10 0,155 0,308 0,384 0,513 0,764 011 11 0,167 0,330 0,410 0,548 0,814 012 12 0,179 0,352 0,436 0,583 0,864 013 13 0,191 0,374 0,462 0,618 0,914 014 14 0,203 0,396 0,48
31、8 0,653 0,964 015 15 0,215 0,418 0,515 0,688 1,014 016 16 0,227 0,440 0,541 0,723 1,064 017 17 0,239 0,462 0,567 0,758 1,114 018 18 0,251 0,484 0,593 0,793 1,164 019 19 0,263 0,506 0,619 0,828 1,214 020 20 0,275 0,528 0,645 0,863 1,264 022 22 0,299 0,572 0,697 0,933 1,364 024 24 0,323 0,616 0,749 1,
32、003 1,464 026 26 0,347 0,660 0,802 1,073 1,564 028 28 0,371 0,704 0,854 1,143 1,664 030 30 0,395 0,748 0,906 1,213 1,764 032 32 0,419 0,792 0,958 1,283 1,864 035 35 0,455 0,858 1,037 1,388 2,014 040 40 0,968 1,167 1,563 2,264 045 45 1,298 1,738 2,514 050 50 1,913 2,764 055 55 3,014 060 60 3,264 a Ta
33、il end code (see Figure 1) b Approximate values(kg/1000 pieces), calculated on the basis of2,76kg/dm 3 , given for information purposes only L 1 0,5 0 +EN2145:1994 6 BSI 12-1999 4 Designation EXAMPLE: NOTEIf necessary, the codeI9005 shall be placed between the description block and the identity bloc
34、k. 5 Marking 5.1 Rivet EN2424, style G 5.2 Material See Figure 2 and Table 4. Table 4 6 Technical specification EN2345 plus EN2000 for the approval of manufacturers Figure 2 Diameter code 024 032 036 040 048 T 0,05 0,13 0,15 D 5 max. 0,8BSEN2145:1994 BSI 12-1999 National annex NA (informative) Commi
35、ttees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical CommitteeACE/12, upon which the following bodies were represented: Association of Electronics, Telecommunications and Busines
36、s Equipment Industries British Industrial Fasteners Federation Ministry of Defence Society of British Aerospace Companies Ltd. National annex NB (informative) Cross-references The British Standards corresponding to the European Standards referred to in the text are identical in number and title with
37、 those given in clause2, with the exception of EN2345 and EN2424 and EN2437 for which no corresponding British Standard exists.BS EN 2145:1994 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It p
38、resents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of B
39、SI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000.
40、 Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:0
41、2089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European
42、 and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of B
43、SI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds t
44、he copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or
45、 otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
