1、BRITISH STANDARD AEROSPACE SERIES BS EN 2148:1993 Rivets, solid, universal head, in aluminium alloy 5056A, inch based series The European Standard EN 2148:1992 has the status of a British Standard UDC 621.884.2-034.715:629.7BSEN2148:1993 This British Standard, having been prepared under the directio
2、nof the Aerospace Standards Policy Committee, waspublished under the authorityof the Standards Boardand comes into effect on 15 February 1993 BSI 11-1999 The following BSI references relate to the work on this standard: Committee reference ACE/12 Draft for comment 89/79413 DC ISBN 0 580 21975 5 Coop
3、erating organizations The European Committee for Standardization (CEN), under whose supervision this European Standard was prepared, comprises the national standards organizations of the following countries: Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark D
4、ansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority of Ireland Ital
5、y Ente Nazionale Italiano di Unificazione Luxembourg Inspection du Travail et des Mines Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus da Qualidade Spain Asociacin Espaola de Normalizacin y Certificacin Sweden Standardiseringskommissio
6、nen i Sverige Switzerland Association suisse de normalisation United Kingdom British Standards Institution Amendments issued since publication Amd. No. Date CommentsBSEN2148:1993 BSI 11-1999 i Contents Page Cooperating organizations Inside front cover National foreword ii Foreword 2 1 Scope 3 2 Norm
7、ative references 3 3 Required characteristics 3 4 Designation 6 5 Marking 6 6 Technical specification 6 National annex NA (informative) Committees responsible Inside back cover National annex NB (informative) Cross-references Inside back cover Figure 1 3 Figure 2 6 Table 1 4 Table 2 5 Table 3 6BSEN2
8、148:1993 ii BSI 11-1999 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN2148:1992 Aerospace series Rivets, solid, universal head, in aluminium alloy5056A, inch based series, published b
9、y the European Committee for Standardization (CEN). EN 2148:1992 was produced as a result of international discussions in which the United Kingdom took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsibl
10、e for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2to6, an inside back cover and a back cover. This standar
11、d has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2148 November 1992 UDC 621.884.2-034.715:629.7 Descriptors: Aircraft industry, full rivet, ro
12、und head rivet, aluminium alloy, dimension, designation, marking English version Aerospace series Rivets, solid, universal head, in aluminium alloy 5056A, inch based series Srie arospatiale Rivets ordinaires, tte ronde aplatie, en alliage daluminium 5056A, srie base inches Luft- und Raumfahrt Vollni
13、ete, mit Universalkopf, aus Aluminiumlegierung5056A, Inch-Reihe This European Standard was approved by CEN on 1992-11-16. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard witho
14、ut any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language ma
15、de by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy
16、, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and United Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1992 Copyright reserved to CEN members Ref. No
17、. EN 2148:1992 EEN2148:1992 BSI 11-1999 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this standard has successively received the approval of
18、the National Associations and the Official Services of the member countries of AECMA, prior to its presentation toCEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May1993, and conflicting nati
19、onal standards shall be withdrawn at the latest by May1993. According to the CEN/CENELEC Internal Regulations, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway,
20、 Portugal, Spain, Sweden, Switzerland and the UnitedKingdom.EN2148:1992 BSI 11-1999 3 1 Scope This standard specifies the characteristics of solid rivets, with universal head, inch based series, in aluminium alloy, for maximum operating temperature120 C. 2 Normative references This European Standard
21、 incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are listed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to thi
22、s European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN 2000, Aerospace series Quality assurance EN aerospace products Approval of the quality system of manufacturers. EN 2117, Aerospace series Al
23、uminium alloy 5056A-H32 wire for solid rivets D k 10mm 1) . EN 2345, Aluminium and aluminium alloy rivets Technical specification Aerospace series 1) . EN 2424, Aerospace series Identification marking of standard fasteners 1) . 3 Required characteristics 3.1 Configuration Dimensions Masses SeeFigure
24、 1 andTable 1 andTable 2. Dimensions and tolerances are expressed in millimetres. 3.2 Material EN 2117 The rivet shall be delivered in H32 condition. 1) Published as AECMA standard at the date of publication of the present standard 1)The length range is limited (seeTable 2). Figure 1 EN2148:1992 4 B
25、SI 11-1999 Table 1 Diameter code D 1 a D 2 D 3 D 4 L 2 L 3 L 4 R 1 R 2 max. min. max. min. max. min. max. min. max. min. 0,08 024 2,45 2,35 5 4,5 2,4 1,8 1,9 1,6 1 1,45 0,8 0,5 2,9 0,15 032 3,25 3,15 6,7 6 3,2 2,4 2,6 2,3 1,4 1 0,7 3,9 040 4,05 3,94 8,3 7,5 4 3 3,2 2,8 1,7 1,95 1,2 0,8 4,9 0,25 048
26、4,85 4,73 10 9 4,8 3,6 3,8 3,3 2 1,5 1 5,9 056 5,65 5,53 11,7 10,5 5,6 4,2 4,5 3,9 2,4 1,8 1,2 6,8 064 6,45 6,33 13,3 12,1 6,4 4,8 5,1 4,5 2,7 2,1 1,4 7,8 080 8,03 7,9 16,7 15,1 8 6 6,4 5,6 3,4 2,4 1,6 9,8 096 9,63 9,5 20 18,1 9,6 7,2 7,7 6,7 4,1 3 2 11,7 a D 1max. may increase by 0,03, over length
27、L 3 .+0,2 0EN 2148:1992 BSI 11-1999 5 Table 2 Diameter code 024 032 040 048 056 064 080 096 Length a Mass a Mass a Mass a Mass a Mass a Mass a Mass a Mass code L 1N R kg/1000 pieces N R kg/1000 pieces N R kg/1000 pieces N R kg/1000 pieces N R kg/1000 pieces N R kg/1000 pieces N R kg/1000 pieces N R
28、kg/1000 pieces b b b b b b b b 004 4 0,083 0,176 005 5 0,095 0,198 006 6 0,107 0,220 0,373 007 7 0,119 0,242 0,408 008 8 0,131 0,264 0,443 0,664 009 9 0,143 0,286 0,478 0,714 010 10 0,155 0,308 0,513 0,764 1,137 011 11 0,167 0,330 0,548 0,814 1,205 012 12 0,179 0,352 0,583 0,864 1,273 1,734 014 14 0
29、,203 0,396 0,653 0,964 1,409 1,912 3,266 016 16 0,227 0,440 0,723 1,064 1,545 2,090 3,544 018 18 0,251 0,484 0,793 1,164 1,681 2,268 3,822 5,868 020 20 0,275 0,528 0,863 1,264 1,817 2,446 4,100 6,266 022 22 0,299 0,572 0,933 1,364 1,953 2,624 4,378 6,664 024 24 0,323 0,616 1,003 1,464 2,089 2,802 4,
30、656 7,062 026 26 0,347 0,660 1,073 1,564 2,225 2,980 4,934 7,460 028 28 0,371 0,704 1,143 1,664 2,361 3,158 5,212 7,858 030 30 0,395 0,748 1,213 1,764 2,497 3,336 5,490 8,256 032 32 0,419 0,792 1,283 1,864 2,633 3,514 5,768 8,654 035 35 0,455 0,858 1,388 2,014 2,837 3,781 6,185 9,251 040 40 0,968 1,
31、563 2,264 3,177 4,226 6,880 10,246 045 45 1,738 2,514 3,517 4,671 7,575 11,241 050 50 1,913 2,764 3,857 5,116 8,270 12,236 055 55 3,014 4,197 5,561 8,965 13,231 060 60 3,264 4,537 6,006 9,660 14,226 a Tail end code (seeFigure 1) b Approximate values, calculated on the basis of 2,76 kg/dm 3 , given f
32、or information purpose only0,5 + 0EN2148:1992 6 BSI 11-1999 4 Designation Example: NOTEIf necessary, the originator code19005shall be placed between the description block and the identity block. 5 Marking 5.1 Rivet identification EN 2424, style G 5.2 Material identification SeeFigure 2 andTable 3. S
33、ymbol at manufacturers option Table 3 6 Technical specification EN 2345 except for approval of manufacturers, see EN2000. Figure 2 Diameter code 024 032 040 048 056 064 080 096 T 0,05 0,13 0,15 0,2 S max. 0,8 D 5max. = D 1max. (seeTable 1)BSEN2148:1993 BSI 11-1999 National annex NA (informative) Com
34、mittees responsible The United Kingdom participation in the preparation of this European Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/12, upon which the following bodies were represented: Association of Electronics, Telecommunications and Busi
35、ness Equipment Industries British Industrial Fasteners Federation Ministry of Defence Society of British Aerospace Companies Ltd. National annex NB (informative) Cross-references The British Standards corresponding to the European Standards referred to in the text are identical in number and title w
36、ith those given in clause2, with the exception of EN2117, EN2345 and EN2424 for which no corresponding British Standards exist.BS EN 2148:1993 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing BritishStandards. It p
37、resents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is the constant aim of B
38、SI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cover. Tel:02089969000.
39、 Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Customer Services. Tel:0
40、2089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information on national, European
41、 and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of B
42、SI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds t
43、he copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or
44、 otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
