1、BRITISH STANDARD AEROSPACE SERIES BS EN 2361:1989 Specification for Ball-ends, double shank in corrosion resisting steel swaged on type, control cable Dimensions and loads This European Standard EN2361 has the status of a British Standard. UDC 629.7.05:621.854:621.85.052.004.1BS EN2361:1989 This Bri
2、tish Standard, having been prepared under the directionof the AerospaceStandards Policy Committee, waspublished underthe authorityof the Board of BSIand comes into effect on 29 September 1989 BSI 01-2000 The following BSI references relate to the work on this standard: Committee reference ACE/14 Dra
3、ft for comment 88/70402 DC ISBN 0 580 17625 8 Cooperating organizations The European Committee for Standardization, under whose supervision this European Standard was prepared, comprises the national standards organizations of the following Western European countries. Austria Oesterreichisches Normu
4、ngsinstitut Belgium Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Ireland National Standards Authori
5、ty of Ireland Italy Ente Nazionale Italiano di Unificazione Netherlands Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus de Qualidade Spain Instituto Espaol de Normalizacin Sweden Standardiseringskommissionen i Sverige Switzerland Association suisse
6、 de normalisation United Kingdom British Standards Institution Amendments issued since publication Amd. No. Date of issue CommentsBS EN2361:1989 BSI 01-2000 i Contents Page Cooperating organizations Inside front cover National foreword ii Brief history 2 Text of EN 2361 3 National appendix A Inside
7、back cover National appendix B Inside back coverBS EN2361:1989 ii BSI 01-2000 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN2361 “Aerospace series. Ball ends, double shank in corrosio
8、n resisting steel swaged on type, control cable. Dimensions and loads”, published by the European Committee for Standardization (CEN). EN2361 was produced as a result of international discussion in which the UK took an active part. A British Standard does not purport to include all the necessary pro
9、visions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page
10、, pages2 to4, an inside back cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2361 September 1988 UDC: 629
11、.7.05:621.854:621.85.052.004.1 Key words: Aircraft industry, flight control, flexible cable, cable-end, crimping end piece, dimensions, breaking loads. English version Aerospace series Ball-ends, double shank in corrosion resisting steel swaged on type, control cable Dimensions and loads Srie arospa
12、tiale Embouts sphre centrale en acier rsistant la corrosion sertir sur cbles de commandes Dimensions et charges Luft- und Raumfahrt Seilschuhe mit Kugelkopf, doppelseitig aus korrosionsbestndigem Stahl zum Aufquetschen auf Steuerseile Mae und Belastungen This European Standard was accepted by CEN on
13、1988-03-17. CEN members are bound to comply with the requirements of CEN Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards
14、may be obtained on application to the CEN Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to C
15、EN Central Secretariat has the same status as the official versions. CEN members are the national standards organizations of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CEN European Committe
16、e for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels CEN1988 Copyright reserved to all CEN members Ref. No. EN 2361:1988 EEN2361:1988 BSI 01-2000 2 Brief history This draft European Standard has been prepared by
17、the European Association of Aerospace Manufacturers (AECMA). After enquiries and votes carried out in accordance with the rules of this Association, this draft has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its
18、 presentation to CEN. In accordance with the Common CEN/CENELEC Rules, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Ireland, Italy, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. Cont
19、ents Page Brief history 2 1 Scope and field of application 3 2 References 3 3 Required characteristics 3 4 Designation 4 5 Marking 4 6 Technical specification 4 Figure 3 Table 4EN2361:1988 BSI 01-2000 3 1 Scope and field of application This standard specifies the characteristics of corrosion resisti
20、ng steel ball-ends for swaging on to aircraft control cables. 2 References ISO 2020, Aerospace Mechanical system parts Preformed flexible steel wire rope for aircraft controls Technical specification. EN 2465, Steel FE-PA 11 Softened Bars D e 100mm Aerospace series. EN 2516, Aerospace series Passiva
21、tion of corrosion resistant steels 1) . EN 2569, Aerospace series Control cable fittings and turnbarrels Technical specification 1) . 3 Required characteristics 3.1 Dimensions Tolerances Loads Mass The configuration shall correspond to the Figure and the dimensions shall conform to the values given
22、in the Figure and the Table. 3.2 Surface roughness See Figure. 3.3 Material Steel EN 2465. 3.4 Surface treatment Passivation EN 2516. 1) In preparation Figure EN2361:1988 4 BSI 01-2000 Table 4 Designation Each ball-end for swaging on to cables shall only be designated as in the following example: NO
23、TEIf necessary, originator code S9005 may be introduced between the description block and identity block. 5 Marking In addition to the manufacturers own marking, each ball-ends for swaging on to cables shall be marked using the identity block as defined in clause4 of this standard. The position and
24、method of marking are at manufacturers option. For Ball-ends with code cable 16 and 24 marking shall be on the package only. 6 Technical specification The ball-ends for swaging on to cables supplied according to this standard shall conform with the requirements of EN2569. Dimensions in millimetres C
25、able D F G J L N P Q Mass g Minimum breaking load kN b Code Nominal diameter 0,25 0,25 16 1,6 5,28 0,7 2,1 3,25 9 1,8 2 2,8 0,6 2,15 24 2,4 7,05 0,9 2,8 4,17 13,1 2,6 2,9 3,6 1,4 4,45 32 3,2 8,78 1,2 3,5 5,56 17,3 3,5 3,9 4,8 2,8 8,90 40 4 10,68 1,4 4,2 6,48 21,4 4,3 4,7 5,6 4,8 12,45 48 4,8 12,40 1
26、,7 4,9 7,46 25,5 5,1 5,6 6,4 9 18,60 56 5,6 14,10 1,9 5,6 8,82 29,6 5,9 a 7,5 13 24,90 64 6,4 15,88 2,1 6,3 10,20 33,8 6,7 a 8,7 18,9 31,20 a No internal taper. b Equal to the one of the cable used according to ISO 2020. 0 0,1 0 0,1 + 0,5 0 + 0,1 0 + 0,2 0 0 0,2BS EN2361:1989 BSI 01-2000 National ap
27、pendix A The United Kingdom participation in the preparation of this European Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Technical Committee ACE/14 upon which the following bodies were represented: British Independent Steel Producers Association Civil Aviation Auth
28、ority (Airworthiness Division) Federation of Wire Rope Manufacturers of Great Britain Ministry of Defence Society of British Aerospace Companies Limited Stainless Steel Wire Export Group National appendix B The British Standards corresponding to the European and International Standards referred to i
29、n the text are identical in number and title with those given in clause2 with the exception of ISO2020 for which the related British Standard is BS W13.BS EN 2361:1989 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for prepari
30、ng BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It
31、 is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside fron
32、t cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to
33、 Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of informat
34、ion on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048.
35、 Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publi
36、cations. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, p
37、hotocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
