1、BRITISH STANDARD AEROSPACE SERIES BS EN 2515:1990 Specification for Rod ends, adjustable single fork and threaded shank Dimensions and loads This European Standard EN 2515 has the status of a British Standard.BS EN2515:1990 This British Standard was published under the authorityofthe Board of BSIand
2、comes into effect on 31December1990 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference ACE/14 Draft for comment 89/79499 DC ISBN 0 580 19070 6 Cooperating organizations The European Committee for Standardization, under whose supervision this European St
3、andard was prepared, comprises the national standards organizations of the following Western European countries. Austria Oesterreichisches Normungsinstitut Belgium Institut belge de normalisation Denmark Dansk Standardiseringsraad Finland Suomen Standardisoimisliito, r.y. France Association franaise
4、 de normalisation Germany Deutsches Institut fr Normung e.V. Greece Hellenic Organization for Standardization Iceland Technological Institute of Iceland Ireland National Standards Authority of Ireland Italy Ente Nazionale Italiano di Unificazione Luxemburg Inspection du Travail et des Mines Netherla
5、nds Nederlands Normalisatie-instituut Norway Norges Standardiseringsforbund Portugal Instituto Portugus de Qualidade Spain Asociacin Espaola de Normalizacin y Certificacin Sweden Standardiseringskommissionen i Sverige Switzerland Association suisse de normalisation United Kingdom British Standards I
6、nstitution Amendments issued since publication Amd. No. Date of issue CommentsBSEN2515:1990 BSI 12-1999 i Contents Page Cooperating organizations Inside front cover National foreword ii Brief history 2 Text of EN 2515 3 National appendix A Inside back cover National appendix B Inside back coverBSEN2
7、515:1990 ii BSI 12-1999 National foreword This British Standard has been prepared under the direction of the Aerospace Standards Policy Committee and is the English language version of EN 2515 “Aerospace series. Rod ends, adjustable single fork and threaded shank. Dimensions and loads”, published by
8、 the European Committee for Standardization (CEN). EN2515 was produced as a result of international discussion in which the UK took an active part. A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct
9、application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theENtitle page, pages 2 to 6, an inside back cover and a back cover. This standard has been updated
10、 (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN 2515 June 1990 UDC: 629.7.02:621.827.1:621.85.053.004.1 Key words: Aircraft industry, flight control, rod ends,
11、 threated ends, dimensions, static loads English version Aerospace series Rod ends, adjustable single fork and threaded shank Dimensions and loads Srie arospatiale Embouts rglables chape simple et tige filete Dimensions et charges Luft- und Raumfahrt Einstellbare Gabelkpfe einfach, mit Gewindeschaft
12、 Mae und Belastungen This European Standard was accepted by CEN on 1990-01-10. CEN members are bound to comply with the requirements of CEN Internal Regulations which stipulate the conditions for giving this European Standard the status of a national standard without any alteration. Up-to-date lists
13、 and bibliographical references concerning such national standards may be obtained on application to the CEN Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, French, German). A version in any other language made by translation under the res
14、ponsibility of a CEN member into its own language and notified to CEN Central Secretariat has the same status as the official versions. CEN members are the national standards organizations of Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxemburg, Netherlands
15、, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels CEN 1990 Copyright reserved to all CEN members Ref. No. EN 2515:1990 EEN
16、2515:1990 BSI 12-1999 2 Brief history This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inquiries and votes carried out in accordance with the rules of this Association, this Standard has successively received the approval of the National
17、Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. According to the Common CEN/CENELEC Rules, the following countries are bound to implement this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland,
18、Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and UnitedKingdom. Contents Page Brief history 2 1 Scope and field of application 3 2 References 3 3 Required characteristics 3 4 Designation 6 5 Marking 6 6 Technical specification 6 Figure 4 Table 5EN2515:1990 BSI 12-1999
19、 3 1 Scope and field of application This standard specifies the characteristics of adjustable rod ends consisting of a rod end body with threaded shank consisting of: a single fork; a circumferential groove to identify location; an optional longitudinal groove for locking purposes. These rod ends ar
20、e intended for flight control rods or rods for aerospace structures. The cadmium plating restricts the application to temperature not exceeding 235 C. 2 References ISO 3353, Aerospace construction Rolled threads Runout and lead threads. ISO 5855-1, Aerospace MJ Threads Part 1: General requirements.
21、ISO 5855-2, Aerospace MJ Threads Part 2: Limit dimensions for bolts and nuts. EN 2133, Cadmium plating of steels with maximum specified tensile strength equal to or less than1450MPa, and copper and copper alloys Aerospace series 1) . EN 2137, Steel FE-PL75 1100 MPau R mu1250MPa Bars D e u 100mm Aero
22、space series 1) . EN 2438, Steel FE-PL62 900 MPa u R m u 1100MPa Bars D eu 40 mm Aerospace series 1) . EN 2601, Aerospace series Fork ends Technical specification 2) . EN 2791, Aerospace series Rod ends, adjustable single fork and threaded shank Dimensions and loads 3) . 3 Required characteristics 3
23、.1 Dimensions Tolerances Configuration: SeeFigure. Dimensions and tolerances: SeeFigureandTable, values after cadmium plating. 3.2 Surface SeeFigure, values before cadmium plating. 3.3 Materials Steel EN2137 or EN2438. 1) Published as AECMA standard. 2) In preparation. 3) Published as AECMA pre-stan
24、dard.EN2515:1990 4 BSI 12-1999 3.4 Surface treatment Cadmium plating, except on the bore C: EN2133,7m to20m except thread5m to10m NOTEThe circumferential groove and the longitudinal groove under distance M, shall be painted red. Figure EN 2515:1990 BSI 12-1999 5 Table Dimensions in millimetres Fork
25、Thread Rod end Size Code A B C D E F G H J K Thread designation a L M b N P R S T V Ultimate load kN Mass . g J7 0,25 0,25 0,1 0.25 min. max. V c 14 20,2 6 12,0 30 19,5 24 0,5 2 13 MJ 10 1,25 4h6h 39 22 2,4 8,0 0,8 33 40 54 W c 15 22,2 8 13,9 36 21,5 30 0,8 2 15 MJ 12 1,25 4h6h 44 25 2,4 10,2 0,8 38
26、 58 81 Y 20 28,2 10 17,8 41 27,0 34 0,8 3 17 MJ 14 1,5 4h6h 50 31 3,2 12,2 1,0 40 4 44 83 132 a Thread: According to ISO 5855-1 and ISO 5855-2 rolled. b M: Minimum length of engaged threads, includes thickness of lock washers and height of nut. c The codes V and W shall not be used for new design (s
27、eeEN2791). + 0,1 0 + 0,2 0 + 0,2 0 + 1 0 + 1 0 + 0,1 0 0 0,1 0 1 0 0, 25EN2515:1990 6 BSI 12-1999 4 Designation Each adjustable single fork rod end fitting shall only be designated as in the following example: With application of the following codes: NOTEIf necessary, the originator code I9005 may b
28、e introduced between the description block and identity block. 5 Marking In addition to the manufacturers own marking, each rod end (seeFigure) and the package shall be marked, using the identity block specified in clause4 of this standard. 6 Technical specification Rod ends supplied according to th
29、is standard shall conform with the requirements of EN 2601. L = left hand thread R = right hand threadBS EN2515:1990 BSI 12-1999 National appendix A The United Kingdom participation in the preparation of this European Standard was entrusted by the Aerospace Standards Policy Committee (ACE/-) to Tech
30、nical Committee ACE/14 upon which the following bodies were represented: British Independent Steel Producers Association Civil Aviation Authority (Airworthiness Division) Federation of Wire Rope Manufacturers of Great Britain Institute of Petroleum Ministry of Defence Society of British Aerospace Co
31、mpanies Ltd. Stainless Steel Wire Industry Association National appendix B The British Standards corresponding to the European Standards and International Standards referred to in the text are identical in number and title as those given in clause2 with the exception ofISO3353, ISO5855-1 and ISO5855
32、-2 for which the corresponding British Standards are British StandardA231 (identical); BS 6293-1 (identical) and BS6293-2 (identical) respectively.BS EN 2515:1990 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body responsible for preparing Br
33、itishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments or editions. It is t
34、he constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be found on the inside front cov
35、er. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications should be addressed to Cust
36、omer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a wide range of information o
37、n national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subs
38、cribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subsists in all BSI publicatio
39、ns. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photoc
40、opying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
