1、BRITISH STANDARD AEROSPACE SERIES BS EN 3151:1995 Dowels, plain, in heat resisting nickel base alloy NI-P100HT (Inconel718) The European Standard EN3151:1995 has the status of a BritishStandard ICS 40.040.20BSEN3151:1995 This BritishStandard, having been prepared under the directionof the Engineerin
2、g SectorBoard, was published underthe authority of the Standards Board and comesintoeffect on 15November1995 BSI 12-1999 The following BSI references relate to the work on this standard: Committee reference ACE/14 Draft for comment88/76839DC ISBN 0 580 24487 3 Committees responsible for this British
3、Standard The preparation of this BritishStandard was entrusted to Technical Committee ACE/14, Aerospace details and parts, upon which the following bodies were represented: British Iron and Steel Producers Association Civil Aviation Authority (Airworthiness Division) Federation of Wire Rope Manufact
4、urers of Great Britain Institute of Petroleum Ministry of Defence Society of British Aerospace Companies Limited Amendments issued since publication Amd. No. Date CommentsBSEN3151:1995 BSI 12-1999 i Contents Page Committees responsible Inside front cover National foreword ii Foreword 2 1 Scope 3 2 N
5、ormative references 3 3 Required characteristics 3 4 Designation 6 5 Marking 6 6 Quality assurance 6 Figure 1 4 Table 1 4 Table 2 5 List of references Inside back coverBSEN3151:1995 ii BSI 12-1999 National foreword This BritishStandard has been prepared by Technical Committee ACE/14 and is the Engli
6、sh language version of EN3151:1995 Aerospace series Dowels, plain, in heat resisting nickel base alloy NI-P100HT (Inconel718), published by the European Committee for Standardization (CEN). EN3151 was produced as a result of international discussions in which the United Kingdom took an active part.
7、A British Standard does not purport to include all the necessary provisions of a contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Cross-reference Publication referred to C
8、orresponding BritishStandard EN2000:1991 BS EN2000:1992 Quality assurance EN aerospace products Approval of the quality system of manufacturers Summary of pages This document comprises a front cover, an inside front cover, pagesi andii, theEN title page, pages2 to6, an inside back cover and a back c
9、over. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.EUROPEAN STANDARD NORME EUROPENNE EUROPISCHE NORM EN3151 July 1995 ICS 40.040.20 Descriptors: Aircraft industry, locating pin, p
10、ositioning, nickel alloy, heat resistant material, characteristic, dimension, designation English version Aerospace series Dowels, plain, in heat resisting nickel base alloy NI-P100HT (Inconel718) Srie arospatiale Pieds de centrage lisses, en alliage rsistant chaud base de nickel NI-P100HT (Inconel7
11、18) Luft- und Raumfahrt Glatte Zylinderstifte, aus hochwarmfester Nickelbasislegierung NI-P100HT (Inconel718) This European Standard was approved by CEN on 1995-03-06. CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European St
12、andard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national standards may be obtained on application to the Central Secretariat or to any CEN member. This European Standard exists in three official versions (English, Frenc
13、h, German). A version in any other language made by translation under the responsibility of a CEN member into its own language and notified to the Central Secretariat has the same status as the official versions. CEN members are the national standards bodies of Austria, Belgium, Denmark, Finland, Fr
14、ance, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland andUnited Kingdom. CEN European Committee for Standardization Comit Europen de Normalisation Europisches Komitee fr Normung Central Secretariat: rue de Stassart 36, B-1050 Brussels 1
15、995 All rights of reproduction and communication in any form any by any means reserved in all countries to CEN and its members. Ref. No. EN3151:1995 EEN3151:1995 BSI 12-1999 2 Foreword This European Standard has been prepared by the European Association of Aerospace Manufacturers (AECMA). After inqu
16、iries and votes carried out in accordance with the rules of this Association, this standard has successively received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the stat
17、us of a national standard, either by publication of an identical text or by endorsement, at the latest by January 1996, and conflicting national standards shall be withdrawn at the latest by January 1996. According to the CEN/CENELEC Internal Regulations, the following countries are bound to impleme
18、nt this European Standard: Austria, Belgium, Denmark, Finland, France, Germany, Greece, Iceland, Ireland, Italy, Luxembourg, Netherlands, Norway, Portugal, Spain, Sweden, Switzerland and the United Kingdom.EN3151:1995 BSI 12-1999 3 1 Scope This standard specifies the characteristics of plain dowels
19、in NI-P100HT for aerospace applications. NOTEInstallation holes EN3368 2 Normative references This European Standard incorporates by dated or undated reference provisions from other publications. These normative references are cited at the appropriate places in the text and the publications are list
20、ed hereafter. For dated references, subsequent amendments to or revisions of any of these publications apply to this European Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies. EN2000, Aerospace series Qua
21、lity assurance EN aerospace product Approval of the quality system of manufacturers. EN2404, Heat resisting nickel base alloy NI-P100HT Solution treated and precipitation treated Bars Aerospace series 1) . EN2424, Aerospace series Marking of aerospace products. EN3368, Aerospace series Aerospace des
22、ign standard Holes for locating pins 2) . 3 Required characteristics 3.1 Configuration Dimensions Tolerances Masses See Figure 1 and Table 1 and Table 2. Dimensions and tolerances are in millimetres. 3.2 Material EN2404 1) Published as AECMA Standard at the date of publication of this standard 2) Pu
23、blished as AECMA Prestandard at the date of publication of this standardEN3151:1995 4 BSI 12-1999 Table 1 Figure 1 Diameter code D A nom. Tol. nom. Tol. 020 2 r6 0,5 0,1 030 3 040 4 p6 050 5 1 0,2 060 6 070 7 080 8 100 10EN3151:1995 BSI 12-1999 5 Table 2 Length code L 0,25 Diameter code 020 030 040
24、050 060 070 080 100 Mass a Mass a Mass a Mass a Mass a Mass a Mass a Mass a 004 4 0,099 006 6 0,151 0,342 008 8 0,202 0,458 0,817 010 10 0,254 0,574 1,023 1,578 012 12 0,690 1,229 1,900 2,744 014 14 0,806 1,435 2,222 3,208 4,373 016 16 0,922 1,642 2,544 3,671 5,004 6,543 018 18 1,038 1,848 2,867 4,1
25、35 5,635 7,368 020 20 1,154 2,054 3,189 4,599 6,267 8,192 12,816 022 22 1,270 2,260 3,511 5,062 6,898 9,016 14,104 024 24 2,466 3,833 5,526 7,529 9,841 15,392 026 26 2,672 4,155 5,990 8,160 10,665 16,680 028 28 2,878 4,477 6,454 8,791 11,489 17,968 030 30 4,799 6,917 9,422 12,314 19,256 032 32 5,121
26、 7,381 10,053 13,138 20,544 034 34 5,443 7,845 10,684 13,962 21,832 036 36 5,765 8,308 11,316 14,787 23,120 038 38 8,772 11,947 15,611 24,408 040 40 9,236 12,578 16,435 25,696 042 42 9,700 13,209 17,260 26,984 044 44 13,840 18,084 28,272 046 46 14,471 18,909 29,560 048 48 15,103 19,733 30,848 050 50
27、 15,734 20,557 32,136 052 52 21,382 33,424 054 54 22,206 34,712 056 56 23,030 36,000 058 58 37,289 060 60 38,577 062 62 39,865 064 64 41,153 066 66 42,441 068 68 43,729 070 70 45,017 a Mass. kg/1000partsEN3151:1995 6 BSI 12-1999 4 Designation EXAMPLE: NOTEIf necessary, the codeI9005 shall be placed
28、between the description block and the identity block. 5 Marking EN2424, style G 6 Quality assurance EN2000BSEN3151:1995 BSI 12-1999 List of references See national foreword.BS EN 3151:1995 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstitution BSI is the independent national body re
29、sponsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amend
30、ments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee responsible, the identity of which can be fou
31、nd on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, international and foreign standards publications s
32、hould be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise requested. Information on standards BSI provides a w
33、ide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services. Contact the Information Centre. Tel:02089967
34、111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:02089967002. Fax:02089967001. Copyright Copyright subs
35、ists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieval system or transmitted in any form or by an
36、y means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
