1、BS EN3155-064:2009ICS 49.060NO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBRITISH STANDARDAerospace series Electrical contactsused in elements ofconnectionPart 064: Contacts, electrical, coaxial,50 ohms, size 1, female, type D, solder,class R Product standardThis British Stan
2、dardwas published under theauthority of the StandardsPolicy and StrategyCommittee on 30 June2009. BSI 2009ISBN 978 0 580 58616 3Amendments/corrigenda issued since publicationDate CommentsBS EN 3155-064:2009National forewordThis British Standard is the UK implementation of EN 3155-064:2009.The UK par
3、ticipation in its preparation was entrusted to TechnicalCommittee ACE/6, Aerospace avionic electrical and fibre optictechnology.A list of organizations represented on this committee can be obtained onrequest to its secretary.This publication does not purport to include all the necessary provisionsof
4、 a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunityfrom legal obligations.BS EN 3155-064:2009EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 3155-064May 2009ICS 49.060English VersionAerospace series - Electrical contacts used in
5、elements ofconnection - Part 064: Contacts, electrical, coaxial, 50 ohms,size 1, female, type D, solder, class R - Product standardSrie arospatiale - Contacts lectriques utiliss dans lesorganes de connexion - Partie 064 : Contacts lectriquescoaxiaux, 50 ohms, taille 1, femelles, type D, souder,class
6、e R - Norme de produitLuft- und Raumfahrt - Elektrische Kontakte zur Verwendungin Verbindungselementen - Teil 064: Elektrische koaxiale,Buchsenkontakte, 50 Ohm, Gre 1, Typ D, zum Lten,Klasse R - ProduktnormThis European Standard was approved by CEN on 31 January 2009.CEN members are bound to comply
7、with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management C
8、entre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficia
9、l versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia
10、, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: Avenue Marnix 17, B-1000 Brussels 2009 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national M
11、embers.Ref. No. EN 3155-064:2009: EBS EN 3155-064:2009EN 3155-064:2009 (E) 2 Contents Page Foreword 3Introduction .41 Scope 52 Normative references 53 Terms and definitions .54 Required characteristics .55 Designation . 136 Marking 137 Delivery conditions . 138 Technical specification 13Bibliography
12、 . 14BS EN 3155-064:2009EN 3155-064:2009 (E) 3 Foreword This document (EN 3155-064:2009) has been prepared by the Aerospace and Defence Industries Association of Europe - Standardization (ASD-STAN). This European Standard shall be given the status of a national standard, either by publication of an
13、identical text or by endorsement, at the latest by November 2009, and conflicting national standards shall be withdrawn at the latest by November 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not b
14、e held responsible for identifying any or all such patent rights. After enquiries and votes carried out in accordance with the rules of this Association, this Standard has received the approval of the National Associations and the Official Services of the member countries of ASD, prior to its presen
15、tation to CEN. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, I
16、reland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. BS EN 3155-064:2009EN 3155-064:2009 (E) 4 Introduction The contacts defined by this standard are derived from those of SAE-AS390
17、29/98, and are intermateable with those of SAE-AS39029/97. BS EN 3155-064:2009EN 3155-064:2009 (E) 5 1 Scope This standard specifies the required characteristics, tests and tooling applicable to female electrical coaxial contacts, size 1, type D, class R, used in elements of connection according to
18、EN 3155-002. It is intended to be used together with EN 3155-001. The associated male contacts are defined in EN 3155-063. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undat
19、ed references, the latest edition of the referenced document (including any amendments) applies. EN 2591-100*, Aerospace series Elements of electrical and optical connection Test methods Part 100: General EN 3155-001:2008, Aerospace series Electrical contacts used in elements of connection Part 001:
20、 Technical specification1EN 3682-001, Aerospace series Connectors, plug and receptacle, electrical, rectangular, interchangeable insert type, rack to panel, operating temperature 150 C continuous Part 001: Technical specification TR 6058, Aerospace series Cable code identification list23 Terms and d
21、efinitions For the purposes of this standard, the terms and definitions given in EN 3155-001:2008 apply. 4 Required characteristics 4.1 Specific characteristics Type D contacts are for application where contacts with a screening feature are requested and class R corresponds to an operating temperatu
22、re range from 65 C to 150 C. 4.2 Dimensions and mass See Figures 1 and 2. Dimensions and tolerances are given in millimetres and apply after surface treatment. *All parts quoted in this document. 1 Published as ASD Prestandard at the date of publication of this standard. 2 Published as ASD Technical
23、 Report at the date of publication of this standard. BS EN 3155-064:2009EN 3155-064:2009 (E) 6 Key 1 Dotted shape optional 2 Form tab ends to meet Figure 1 Inner socket contact2 1 BS EN 3155-064:2009EN 3155-064:2009 (E) 7 Key 1 Screw size 4-40 UNC 19,05 0,25 (.750 .010) length (4 PLS) ANSI B 18-6-3
24、2 4-40 UNC-2B thread (4 PLS) 3 Seal (optional) 4 C-clip MS 16 626-1050 5 O-ring MS 28 775-111 6 Washer 7 13,26 free length spring constant, 4,75 Nm Figure 2 Mass: 46 g. 1 55.88 max. 3 45 X 2 6max.min. 7 X Y Y BS EN 3155-064:2009EN 3155-064:2009 (E) 8 4.3 Marking by colour code Not applicable. 4.4 Ma
25、terial, surface treatment Outer body material : copper alloy. Center contact : copper alloy. Surface treatment : gold on appropriate undercoat, thickness of protection not specified, selective protection permitted. Dielectric : PTFE, or equivalent. Gasket : Silicone rubber. 4.5 Typical cables See Fi
26、gure 3 and Table 1. Figure 3 Table 1 Permissible cable group code Permissible cable code according to TR 6058 Dimensions of cable A B C D min. max. min. max. min. max. min. max. A WA B XB 0,94 2,83 3,07 3,87 4,11 4,83 5,07XG 0,94 2,83 3,07 3,25 3,49 4,68 4,92C XD 2,25 7,10 7,40 7,74 8,04 10,63 10,97
27、XR 2,40 7,13 7,37 7,77 7,94 10,15 10,65XS 2,40 7,13 7,37 8,41 8,65 10,65 11,15BS EN 3155-064:2009EN 3155-064:2009 (E) 9 4.6 Cable stripping and wiring method 1) Trim jacket to dimension shown, see Figure 4. 2) Place nut washer and sealing ring on cable. Figure 4 3) Slide braid cone until it stops ag
28、ainst jacket see Figure 5. 4) Comb out braid and cut it to proper length as shown and cut first the dielectric core and after inner conductor to dimensions shown blow, see Figure 5. Figure 5 5) Solder inner contact on inner conductor, see Figure 6. 6) Place front insulator on inner contact and inser
29、t the cable and parts in the body . 7) Tighten nut (5,42 Nm pound torque) 7 6 5 4 12 7 9 12 21 BS EN 3155-064:2009EN 3155-064:2009 (E) 10 Figure 6 4.7 Tests Tests according to EN 2591-100, see Table 2. Table 2 EN 2591- Designation of the test Not applicableApplicable According toEN 3155-001Remarks 1
30、01 Visual examination X 102 Examination of dimensions and mass X See 4.2. 201 Contact resistance - low level X Test temperature: ambient Contact Maximum contact resistance m Initial After test Central 1 1,5 Outer Not applicable 202 Contact resistance at rated current X Contact Maximum contact resist
31、ance m Rated currentA (2503+) C (15003+) C Initial After test After test Central 1 1,5 3,0 1 Outer 0,2 0,4 0,8 7,5 continued BS EN 3155-064:2009EN 3155-064:2009 (E) 11 Table 2 (continued) EN 2591- Designation of the test Not applicableApplicable According to EN 3155-001Remarks 204 Discontinuity of c
32、ontacts in the microsecond range X Method B Duration of discontinuity: 0,1 s Test duration: Throughout the duration of tests EN 2591-402 and EN 2591-403 206 Measurement of insulation resistance X Method C Mated contacts At ambient temperature: 5 000 M At 150 C 2 000 M 207 Voltage proof test X Method
33、 C Proof test voltage at sea level: 2 500 VAC r.m.s. between central contact and outer contact. Proof test voltage at altitude: 600 VAC r.m.s. at 1,1 kPa pressure (33 000 m) Leakage current: 2 mA 212 Surface transfer impedance X 221 Voltage Standing Wave Ratio (VSWR) X 1,70: 1 max. from 0 GHz to 5 G
34、Hz 222 Insertion Loss (I.L.) X 0,3 dB max. from 0 GHz to 5 GHz 301 Endurance at temperature X T = (15005+) C Duration: 1 000 h 305 Rapid change of temperature X TA= (15005+) C TB= ( 6505+) C 306 Mould growth X 307 Salt mist X 315 Fluid resistance X According to EN 3682-001. 402 Shock X Severity 30,
35、Method A, See EN 3682-001 in relation with the figures in clause “Static load“. 403 Sinusoidal and random vibration X According to EN 3682-001, clause “Vibrations“. 406 Mechanical endurance X 417 Tensile strength (crimped connection) X Cable according to TR 6058 code XD Outer: 55,6 daN continued BS
36、EN 3155-064:2009EN 3155-064:2009 (E) 12 Table 2 (concluded) EN 2591- Designation of the test Not applicableApplicable According to EN 3155-001Remarks 418 Gauge insertion/extraction forces (female contacts) X Gauge as described in Figure 7 and Table 3. Insertion Initial = 8,9 N max. After test = 8,9
37、N max. Extraction Initial = 0,55 N min. After test = 0,55 N min. 501 Soft solderability X 503 Contact deformation after crimping X 508 Measurement of thickness of coating on contacts X The measured thickness shall be recorded. 509 Adhesion of coating on contacts X 513 Magnetic permeability X 514 Sol
38、derability of contacts with self-contained solder and flux X 4.8 Gauge See Figure 7 and Table 3. Figure 7 Table 3 Dimensions in millimetres A Gauge min. 0 0,005 Gauge max. + 0,005 0 2,29 2,33BS EN 3155-064:2009EN 3155-064:2009 (E) 13 5 Designation EXAMPLE Description block CONTACT, ELECTRICAL Identi
39、ty block EN3155-064F01A1 Number of this standard Type of contact: F = female Code size Permissible cable group code Code for contact model (see Table 4) NOTE If necessary, the code I9005 should be placed between the description block and the identity block. Table 4 Code Contact model 1 Unsealed vers
40、ion2 Semi environmental version 6 Marking See EN 3155-001. 7 Delivery conditions The contacts are packaged and identified individually. Conditioning shall provide protection of the contacts against any eventual damage. Packaging shall include: a) the manufacturers name; b) the designation defined in
41、 Clause 5; c) the manufacturers reference; d) the manufacturing date code (year-week). 8 Technical specification See EN 3155-001. BS EN 3155-064:2009EN 3155-064:2009 (E) 14 Bibliography 1 EN 3155-002, Aerospace series Electrical contacts used in elements of connection Part 002: List and utilization
42、of contacts 2 EN 3155-063, Aerospace series Electrical contacts used in elements of connection Part 063: Contacts, electrical, coaxial, 50 ohms, size 1, male, type D, solder, class R Product standard 3 SAE-AS39029/97, Contacts, electrical connector, pin, crimp removable, coaxial size 1 (for DOD-C-83
43、527 connectors)34 SAE-AS39029/98, Contacts, electrical connector, socket, crimp removable, coaxial size 1 (for DOD-C-83527 connectors)33Published by: Society of Automotive Engineers, Inc. (SAE), 400 Commonwealth Drive, Warrendale, PA 15096-0001, USA. BS EN 3155-064:2009This page has been intentional
44、ly left blank BS EN3155-064:2009BSI GroupHeadquarters 389Chiswick High Road,London, W4 4AL, UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 - British Standards InstitutionBSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and
45、at theinternational level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of BritishStandards should make sure that they possess the latest amendments oreditions.It is the constant aim of BSI to improve the quality of our products and servi
46、ces.We would be grateful if anyone finding an inaccuracy or ambiguity while usingthis British Standard would inform the Secretary of the technical committeeresponsible, the identity of which can be found on the inside front cover. Tel:+44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members
47、an individual updating service called PLUS which ensuresthat subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards publications should beaddressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 89967
48、001 Email: You may also buy directly using a debit/creditcard from the BSI Shop on the Website http:/ response to orders for international standards, it is BSI policy to supply theBSI implementation of those that have been published as British Standards,unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European andinternational standards through its Library and its Technical Help to ExportersService. Various BSI electro
