1、 g49g50g3g38g50g51g60g44g49g42g3g58g44g55g43g50g56g55g3g37g54g44g3g51g40g53g48g44g54g54g44g50g49g3g40g59g38g40g51g55g3g36g54g3g51g40g53g48g44g55g55g40g39g3g37g60g3g38g50g51g60g53g44g42g43g55g3g47g36g58for transmission of digital data Part 003: Solder receptacle Product standardThe European Standard
2、EN 3716-003:2006 has the status of a British StandardICS 49.060Aerospace series Connectors, single-way with triaxial interface, BRITISH STANDARDBS EN 3716-003:2006BS EN 3716-003:2006This British Standard was published under the authority of the Standards Policy and Strategy Committee on 29 September
3、 2006 BSI 2006ISBN 0 580 49242 7Amendments issued since publicationAmd. No. Date CommentsThis publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application.Compliance with a British Standard cannot confer immunity from legal obl
4、igations.National forewordThis British Standard was published by BSI. It is the UK implementation of EN 3716-003:2006.The UK participation in its preparation was entrusted by Technical Committee ACE/6, Aerospace avionic electrical and fibre optic technology, to Subcommittee ACE/6/-/3, Aerospace Conn
5、ectors.A list of organizations represented on ACE/6/-/3 can be obtained on request to its secretary.EUROPEAN STANDARDNORME EUROPENNEEUROPISCHE NORMEN 3716-003May 2006ICS 49.060English VersionAerospace series - Connectors, single-way with triaxial interface,for transmission of digital data - Part 003
6、: Solder receptacle -Product standardSrie arospatiale - Connecteur, monovoie, avec interfacetriaxiale, pour transmission de donnes numriques - Partie003 : Embase souder - Norme de produitLuft- und Raumfahrt - Steckverbinder, triaxial fr digitaleDatenbertragung in einer Richtung - Teil 003: Steckdose
7、,ltbar - ProduktnormThis European Standard was approved by CEN on 20 February 2006.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and
8、bibliographical references concerning such nationalstandards may be obtained on application to the Central Secretariat or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility
9、of a CEN member into its own language and notified to the Central Secretariat has the same status as the officialversions.CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,Germany, Greece, Hungary, Iceland, Ireland, Italy, La
10、tvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMIT EUROPEN DE NORMALISATIONEUROPISCHES KOMITEE FR NORMUNGManagement Centre: rue de Stassart, 36 B-1050 Brussel
11、s 2006 CEN All rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 3716-003:2006: E2 Contents Page Foreword 3 1 Scope .4 2 Normative references .4 3 Terms and definitions.4 4 Required characteristics 4 5 Technical specification.6 6 Designation .
12、6 7 Marking 7 8 Assembly instructions7 EN 3716-003:20063 Foreword This European Standard (EN 3716-003:2006) has been prepared by the European Association of Aerospace Manufacturers - Standardization (AECMA-STAN). After enquiries and votes carried out in accordance with the rules of this Association,
13、 this Standard has received the approval of the National Associations and the Official Services of the member countries of AECMA, prior to its presentation to CEN. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, a
14、t the latest by November 2006, and conflicting national standards shall be withdrawn at the latest by November 2006. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN and/or CENELEC shall not be held responsible for identifying
15、any or all such patent rights. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Icel
16、and, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. EN 3716-003:20064 1 Scope This standard specifies the requirements and assembly instructions for solder receptacles, with
17、or without braid connection equipped with a male or female contact, used according to EN 3716-002 on cables conforming to EN 3375-003, EN 3375-004 or EN 3375-005. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, o
18、nly the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 3375-003, Aerospace series Cables, electrical, for signal data transmissions Part 003: Cable, bifilar, double-braid Product standard. 1)EN 3375-004, Aerospace s
19、eries Cables, electrical, for signal data transmissions Part 004: Cable, bifilar, single-braid Product standard. 1)EN 3375-005, Aerospace series Cables, electrical, for signal data transmissions Part 005: Cable, bifilar, double-braid, high immunity Product standard. 1)EN 3716-001, Aerospace series C
20、onnector, single-way, with triaxial interface for transmission of digital data Part 001: Technical specification. EN 3716-002, Aerospace series Connector, single-way, with triaxial interface for transmission of digital data Part 002: Conditions of use and list of product standards. EN 3716-004, Aero
21、space series Connector, single-way, with triaxial interface for transmission of digital data Part 004: Solder plug Product standard. 3 Terms and definitions For the purposes of this standard, the terms and definitions given in EN 3716-001 apply. 4 Required characteristics 4.1 Dimensions and mass 4.1
22、.1 Dimensions See Figure 1. 1) In preparation at the date of publication of this standard. EN 3716-003:20065 Key 1 Manufacturer identification 2 Week 3 2 last figures of year Figure 1 4.1.2 Mass 10 g max. 4.2 Torque of fixing nut 1,13 N.m to 1,7 N.m 4.3 Panel cut-out See Figure 2. Figure 2 4.4 Mater
23、ial and surface treatment See EN 3716-001. EN 3716-003:20066 4.5 Main general characteristics Temperature class: 65 C to 150 C Maximum current: 3 A Insulation resistance: 5 000 M min. Voltage strength: 900 V r.m.s. at sea level Contact resistance: 8 m max. Coupling torque: 1,13 N.m max. Insertion fo
24、rce: 14 N max. Retention force of wired contact: 9 N min. Number of operations: 500 cycles Salt spray: 500 h 4.6 Plug and receptacle combination options This receptacle mates with a plug conforming to EN 3716-004 equipped with a contact of the opposite type. X = type of contact F = female contact M
25、= male contact 5 Technical specification See EN 3716-001. 6 Designation EXAMPLE Description block RECEPTACLE Identity block EN3716-003F1 Number of this standard Type of contact: F : female M male Type of cable: see EN 3716-001, Table 5 EN 3716-003:20067 7 Marking See Figure 1. On the nut: manufactur
26、er identification; yy-ww (year-week) 8 Assembly instructions 8.1 Tooling The hot air generator shall have a minimum output of 800 W and the temperature in the heating zone shall be 420 C 20 C. 8.2 Procedure The product is delivered as a kit comprising: the connector body with hardware; the contact;
27、the ferrule; a heat-shrinkable sleeve. EN 3716-003:20068 8.3 Procedure with screen connection The assembly operation is carried out in the following phases, strip cable as shown in Figure 3. 1 Pre-position heat-shrinkable sleeve and ferrule on the cable Dimensions in millimetres 2 Expose the braid b
28、y stripping the insulation Single braid EN 3375-003 Double braid EN 3375-004 Double braid Mu metal EN 3375-005 3 Pick up and roll back the 1stbraid Cut the Mu metal strip Pick up and roll back the 2ndbraid 4 Align the 2 wires in the pair 5 Cut the fillers 6 Strip the conductors 7 Tin the conductors
29、with Sn63 8 Recut the conductors to the lengths indicated Figure 3 EN 3716-003:20069 9 Introduce the cable to butt into the contact 10 Position the contact in the correct interface positioner (P or S: see Figure 4) 11 Hold in position (see Figure 4) 12 Heat with a hot air generator until the solder
30、rings melt and then continue for about 5 s 13 Visually inspect: ensure that the solder preforms have melted 14 Insert the contact in the connector 15 Install the ferrule 16 Heat with a hot air generator until the solder ring melts and then continue for about 5 s 17 Visually inspect: ensure that the
31、solder preform has melted and the screening braid is in position. 18 Take the heat-shrinkable sleeve over the ferrule and shrink it, beginning on the connector side. Key 1 Heating zone 2 Positioner 3 Holding fixture 4 Cable clamp P: male contact (pin) S: female contact (socket) Figure 4 NOTE The des
32、ign of the positioning tool is given as an indication: the positioner has a standard interface (see EN 3716-001) and the function of the cable clamp is to hold the parts in place during heating and cooling. EN 3716-003:200610 8.4 Procedure without screen connection The procedure is the same, except
33、that the braids are cut to the level of the external insulation, as shown in Figure 5, and the ferrule is not used. 1 Pre-position heat-shrinkable sleeve on the cable Dimensions in millimetres 2 Expose the braid by stripping the insulation Single braid EN 3375-003 Double braid EN 3375-004 Double bra
34、id Mu metal EN 3375-005 3 Cut the braid to the tolerance indicated Cut the Mu metal strip Cut the 2ndbraid 4 Align the 2 wires of the pair 5 Cut the fillers 6 Strip the conductors 7 Tin the conductors with Sn63 8 Recut the conductors to the lengths indicated Key 1 White Blue Figure 5 EN 3716-003:200
35、611 9 Introduce the cable to butt into the contact 10 Position the contact in the correct interface positioner (P or S: see Figure 4) 11 Hold in position (see Figure 4) 12 Heat with a hot air generator until the solder rings melt and then continue for about 5 s 13 Visually inspect: ensure that the s
36、older preforms have melted 14 Insert the contact in the connector 15 Install the heat-shrinkable sleeve and shrink it, beginning on the connector side EN 3716-003:2006BS EN BSI389 Chiswick High RoadLondonW4 4AL3716-003:2006BSI British Standards InstitutionBSI is the independent national body respons
37、ible for preparing British Standards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.RevisionsBritish Standards are updated by amendment or revision. Users of British Standards should make sure that they possess the latest amendment
38、s or editions.It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this British Standard would inform the Secretary of the technical committee responsible, the identity of which can be found o
39、n the inside front cover. Tel: +44 (0)20 8996 9000. Fax: +44 (0)20 8996 7400.BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards.Buying standardsOrders for all BSI, international and foreign standards pub
40、lications should be addressed to Customer Services. Tel: +44 (0)20 8996 9001. Fax: +44 (0)20 8996 7001. Email: ordersbsi-. Standards are also available from the BSI website at http:/www.bsi-.In response to orders for international standards, it is BSI policy to supply the BSI implementation of those
41、 that have been published as British Standards, unless otherwise requested.Information on standardsBSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services a
42、re also available which give details on all its products and services. Contact the Information Centre. Tel: +44 (0)20 8996 7111. Fax: +44 (0)20 8996 7048. Email: infobsi-.Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase pric
43、e of standards. For details of these and other benefits contact Membership Administration. Tel: +44 (0)20 8996 7002. Fax: +44 (0)20 8996 7001. Email: membershipbsi-.Information regarding online access to British Standards via British Standards Online can be found at http:/www.bsi- information about
44、BSI is available on the BSI website at http:/www.bsi-.CopyrightCopyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the international standardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be
45、 reproduced, stored in a retrieval system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI.This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and s
46、ize, type or grade designations. If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained.Details and advice can be obtained from the Copyright & Licensing Manager. Tel: +44 (0)20 8996 7070. Fax: +44 (0)20 8996 7553. Email: copyrightbsi-.
